Multec-S X 14 XE / X 16 XE (L) F0:DATA LIST
| No. | TECH 1 Display | Conditions for Checking | Nominal Value | Trouble Codes | Terminal |
|---|---|---|---|---|---|
| 08 | INTAKE AIR TEMP. | Ignition ON | TECH 1 display approx. ambient temperature | 69, 71 | B4, F15 |
Home/Opel/Corsa/Opel Corsa B (1993-2000)/Repair manual/Fuel Injection Systems/F0: Data List - Test Step 08 Intake Air Temperature
Contents
Wiring diagrams Section: Fuel Injection Systems- Introduction
- The Opel Checking System
- Introduction Multec M 14SE, C14SE, C16SE
- General Instructions / Safety Measures
- Programmable Control Units
- Program Memories and Control Units Model Years 1993, 1993 1/2
- General Instructions/safety Measures
- The Checking System
- Checking Equipment
- Correct Coding of Octane Number Plug (Octane Number Coding), Choice of Fuel
- Block Diagram
- Poor Accelerator Response, Power Loss (Brief Ringing Noise)
- Abbreviations, Definitions
- Components
- Checking with Tech 1
- Survey of System - Survey of Engine Compartment (14SE / C14SE / C16SE)
- Survey of System/survey of Engine Compartment C16XE
- Survey of System Survey of Engine Compartment (X12SZ)
- Control Unit, Part and Catalogue Numbers
- F0: Data List - Test Step 01 Battery Voltage
- Block Diagram, Multec-M (14SE / C14SE / C16SE)
- Block Diagram Multec-S (C16XE)
- Octane Number Plug (Octane No. Coding), Fuel Selection
- Engine Control Units and Program Memories of Model Years '94,'95 and '96
- F0: Data List - Test Step 02 Coolant Temperature
- Features Specific to This System
- Survey of System Block Diagram Multec (X12SZ)
- System Specific Features
- Setting the 0-degree Position for the Throttle Valve
- Throttle Body Valve Assembly
- F0: Data List - Test Step 03 MAP Sensor
- Checking with Diagnostic Switch KM-640
- A, Diagnostic System Check
- F0: Data List - Test Step 04 TPS Signal
- F0:Data List Test Step 01 Battery Voltage
- How to Connect Diagnostic Tester and Establish Communication the B-01
- Engine Management System Motronic M 1.5.5
- Various Problems with Multec Vehicles (Engine Speed Too High, Load Variation Effect).
- F0: Data List - Test Step 05 Engine Speed
- F0:Data List - Test Step 01 Battery Voltage
- F0:Data List Test Step 02 Diag. Request
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0105 MAP Sensor Voltage High
- Engine Compartment Survey Motronic M 1.5.5
- Poor Cold Starting and Irregular Idle in Lower Engine Speed Range. Jerking When Accelerating.
- F0: Data List - Test Step 06 Idle Air Control
- F0:Data List - Test Step 02 Coolant Temperature
- F0:Data List Test Step 03 Immobiliser
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0105 MAP Sensor Voltage Low
- Motronic 1.5.5
- Circuit Diagram Motronic M 1.5.5
- F0: Data List - Test Step 07 02 Sensor Loop
- F0:Data List - Test Step 02 Ron Coding
- F0:Data List - Test Step 03 Mass Air Flow S.
- F0:Data List Test Step 04 Immobiliser Sig.
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0110 Intake Air Temperature Voltage High
- Engine Control Unit
- Wiring Harness Plug Termial Assignment Engine Control Unit
- F0: Data List - Test Step 08 02 Sensor
- F0:Data List - Test Step 03 Coolant Temperature
- F0:Data List - Test Step 04 Engine Load
- F0:Data List Test Step 05 TPS Signal
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0110 Intake Air Temperature Voltage Low
- Ignition Module
- F0: Data List - Test Step 09 02 Integrator
- F0:Data List - Test Step 04 Intake Air Temperature
- F0:Data List - Test Step 05 TPS Signal
- F0:Data List Test Step 06 MAP Sensor
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0115 Coolant Temperature Voltage High
- Hot Film Mass Air Flow Meter
- F0: Data List - Test Step 10 02 Blm Idle Thr.
- F0:Data List - Test Step 05 MAP Sensor
- F0:Data List - Test Step 06 Engine Speed
- F0:Data List Test Step 07 Coolant Temperature
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0115 Coolant Temperature Voltage Low
- Throttle Valve Adjuster
- F0: Data List - Test Step 11 02 Blm Part Thr.
- F0:Data List - Test Step 06 TPS Signal
- F0:Data List - Test Step 07 Iac Cntr. Enable
- F0:Data List Test Step 08 Intake Air Temperature
- Multec Control Unit Listing X14XE and X16XE Engines (Corsa-B)
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0120 Throttle Posit. Sensor Voltage High
- Air-Enclosed Injection Valves
- F0: Data List - Test Step 12 02 Blm Enable
- F0:Data List - Test Step 07 Diag. Request
- F0:Data List - Test Step 08 Idle Air Control
- F0: Data List - Test Step 06 Desired Idle
- F0:Data List Test Step 09 A/c Informat. Sw
- Multec Control Unit - Block Diagram X14XE and X16XE Engines (Corsa-B)
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0120 Throttle Posit. Sensor Voltage Low
- Rapid Initialisation Camshaft Position
- F0: Data List - Test Step 13 Air/fuel Ratio
- F0:Data List - Test Step 08 Fuel Pump Relay
- F0:Data List - Test Step 09 O2 Sensor Loop
- F0: Data List - Test Step 07 Iac Cntr. Enable
- F0:Data List Test Step 10 A/c Load Signal
- Multec Control Unit - Program Memory X14XE and X16XE Engines (Corsa-B)
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0130 O2 Sensor Open Circuit
- F0: Data List - Test Step 14 Vehicle Speed
- F0:Data List - Test Step 09 Park / Neutral Sw.
- F0:Data List - Test Step 10 O2 Sensor
- F0: Data List - Test Step 08 Idle Air Control
- F0:Data List Test Step 11 Park/neutral Sw.
- Terminal Assignment, Wiring Harness Plug Engine Control Unit, X14XE/X16XE Engines
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0170 O2 Sensor Rich Exhaust
- Circuit Diagram
- F0: Data List - Test Step 15 Vehicle Sp.pulse
- F0:Data List - Test Step 10 Torque Control
- F0:Data List - Test Step 11 O2 Integrator
- F0: Data List - Test Step 09 O2 Sensor Loop
- F0:Data List Test Step 12 Fuel Pump Relay
- Diagnosis with Tech 1A - Trouble Code Table X14XE and X16XE Engines (Corsa-B)
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0170 O2 Sensor Lean Exhaust
- Terminal Assignment, Engine Control Unit Motronic Wiring Harness
- F0: Data List - Test Step 16 Ron Coding
- F0:Data List - Test Step 11 Vehicle Sp. Pulse
- F0:Data List - Test Step 12 O2 Blm Enable
- F0: Data List - Test Step 10 O2 Sensor
- F0:Data List Test Step 13 Clear Flood Mode
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0200 Fuel Injector Circuit(s)
- Terminal Assignment, Engine Control Unit Wiring Harness, Instrument Panel
- F0: Data List - Test Step 17 Spark Advance
- F0:Data List - Test Step 12 Vehicle Speed
- F0:Data List - Test Step 13 O2 Blm Cell No.
- F0: Data List - Test Step 11 O2 Integrator
- F0:Data List Test Step 14 Spark Advance
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0200 Injector Valve Voltage High
- Trouble Codes M 1.5.5
- F0: Data List - Test Step 18 Dec. Fuel Cutoff
- F0:Data List - Test Step 13 Desired Idle
- F0:Data List - Test Step 14 O2 Blm Cell Cont.
- F0: Data List - Test Step 12 O2 Blm Cell Cont
- F0:Data List Test Step 15 Knock Voltage
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0200 Injector Valve Voltage Low
- Special Service Tools, X 10 XE Engine
- F0: Data List - Test Step 19 Power Enrichment
- F0:Data List - Test Step 14 Engine Speed
- F0:Data List - Test Step 15 O2 Toggle Rate
- F0: Data List - Test Step 13 O2 Blm Cell No.
- F0:Data List Test Step 16 Knock Pulses
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0230 Fuel Pump Relay Voltage High
- F0: Data List - Test Step 20 Clear Flood Mode
- F0:Data List - Test Step 15 Idle Air Control
- F0:Data List - Test Step 16 O2 Blm Part Ref.
- F0: Data List - Test Step 14 O2 Blm Enable
- F0:Data List Test Step 17 Knock Cell No.
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0230 Fuel Pump Relay Voltage Low
- F0: Data List - Test Step 21 Injection Pulse
- F0:Data List - Test Step 16 Spark Advance
- F0:Data List - Test Step 17 Air/fuel Ratio
- F0: Data List - Test Step 15 O2 Toggle Rate
- F0:Data List Test Step 18 Knock Rtd. cyl.1
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0325 Knock Signal Circuit
- F0: Data List - Test Step 22 Park/neutral Sw.
- F0:Data List - Test Step 17 O2 Sensor Loop
- F0:Data List - Test Step 18 Power Enrichment
- F0: Data List - Test Step 16 EGR Position Cmd
- F0:Data List Test Step 19 Knock Rtd. cyl.2
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0335 Incorrect RPM Signal
- All Vehicles MY'94 with Multec/simtec: TC 24 Set
- F0: Data List - Test Step 23 Diag. Request
- F0:Data List - Test Step 18 O2 Sensor
- F0:Data List - Test Step 19 Clear Flood Mode
- F0: Data List - Test Step 17 EGR Position Fdbk.
- F0:Data List Test Step 20 Knock Rtd. cyl.3
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0340 Camshaft Sensor Incorrect Signal
- F0: Data List - Test Step 24 Controlled RPM
- F0:Data List - Test Step 19 O2 Integrator
- F0:Data List - Test Step 20 Dec. Fuel Cutoff
- F0: Data List - Test Step 18 Air/fuel Ratio
- F0:Data List Test Step 21 Knock Rtd. cyl.4
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0351 Est Line Coil Cyl 1+4 Voltage High
- Explanation of Tables
- F0:Data List - Test Step 20 O2 Blm Enable
- F0:Data List - Test Step 21 Fuel Tank Vent.
- F0:Data List Test Step 22 Sec.air Pump Rel
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0351 Est Line Coil Cyl 1+4 Voltage Low
- How to Check the Table 1 - Diagnostic Plug (Aldl) and Voltage Supply
- F0:Data List - Test Step 21 O2 Blm Cell No.
- F0:Data List - Test Step 22 Fuel Tank Valve
- F0:Data List Test Step 23 Air Control Sol.
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0352 Est Line Coil Cyl 2+3 Voltage High
- Types of Faults - Examples of Tech 1 Displays
- F0:Data List - Test Step 22 O2 Blm Cell Cont
- F0:Data List - Test Step 23 A/c Informat. Sw
- F0: Data List - Test Step 21 Dec. Fuel Cutoff
- F0:Data List Test Step 24 EGR Position Cmd
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0352 Est Line Coil Cyl 2+3 Voltage Low
- Table 2 - Trouble Code Table: Trouble Code 13
- F0:Data List - Test Step 23 Air/fuel Ratio
- F0:Data List - Test Step 24 A/c Load Signal
- F0: Data List - Test Step 22 Fuel Tank Vent.
- F0:Data List Test Step 25 EGR Pos. Fdbk
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0400 Linear EGR System
- Table 2 - Trouble Code Table: Trouble Code 14
- F0:Data List - Test Step 24 Injection Pulse
- F0:Data List - Test Step 25 A/c Relay
- F0: Data List - Test Step 23 Vehicle Speed
- F0:Data List Test Step 26 Fuel Tank Vent.
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0412 Air Control Sol. Voltage High
- Table 2 - Trouble Code Table: Trouble Code 15
- F0:Data List - Test Step 25 Clear Flood Mode
- F0:Data List - Test Step 26 Fuel Pump Relay
- F0: Data List - Test Step 24 Vehicle Sp. Pulse
- F0:Data List Test Step 27 O2 Sensor
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0412 Air Control Sol. Voltage Low
- Table 2 - Trouble Code Table: Trouble Code 21
- F0:Data List - Test Step 26 Dec. Fuel Cutoff
- F0:Data List - Test Step 27 Vehicle Speed
- F0: Data List - Test Step 25 Knock Pulses
- F0:Data List Test Step 28 O2 Sensor Loop
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0443 Fuel Tank Vent. Valve Voltage High
- Table 2 - Trouble Code Table: Trouble Code 22
- F0:Data List - Test Step 27 Power Enrichment
- F0:Data List - Test Step 28 Vehicle Sp. Pulse
- F0: Data List - Test Step 26 Knock Voltage
- F0:Data List Test Step 29 Air/fuel Ratio
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0443 Fuel Tank Vent. Valve Voltage Low
- Table 2 - Trouble Code Table: Trouble Code 24
- F0:Data List - Test Step 28 Iac Cntr. Enable
- F0:Data List - Test Step 29 Knock Control
- F0: Data List - Test Step 27 Knock Rtd. Cyl 1,4
- F0:Data List Test Step 30 O2 Integrator
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0500 No Vehicle Speed Signal
- Table 2 - Trouble Code Table: Trouble Code 33
- F0:Data List - Test Step 29 A/c Informat. Sw
- F0:Data List - Test Step 30 Knock Voltage
- F0: Data List - Test Step 28 Knock Rtd. Cyl 4,1
- F0:Data List Test Step 31 O2 Blm Enable
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0505 Idle Air Control
- Table 2 - Trouble Code Table: Trouble Code 34
- F0:Data List - Test Step 30 A/c Load Signal
- F0:Data List - Test Step 31 Knock Cell No.
- F0: Data List - Test Step 29 Knock Rtd. Cyl 2,3
- F0:Data List Test Step 32 O2 Blm Cell No.
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0560 Battery Voltage High
- Table 2 - Trouble Code Table: Trouble Code 35
- F0:Data List - Test Step 31 A/c Relay
- F0:Data List - Test Step 32 Knock Rtd. Cyl. 1
- F0: Data List - Test Step 30 Knock Rtd. Cyl 3,2
- F0:Data List Test Step 33 O2 Blm Cell Cont
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P0602 Control Module Programming Error
- Table 2 - Trouble Code Table: Trouble Code 44
- F0:Data List - Test Step 32 A/c Cutoff
- F0:Data List - Test Step 33 Knock Rtd. Cyl. 2
- F0: Data List - Test Step 31 Park/neutral Sw.
- F0:Data List Test Step 34 Engine Speed
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1120 Throttle Broken Hose
- Table 2 - Trouble Code Table: Trouble Code 45
- F0:Data List - Test Step 33 CO Fuel Correc.
- F0:Data List - Test Step 34 Knock Rtd. Cyl. 3
- F0: Data List - Test Step 32 Torque Control
- F0:Data List Test Step 35 Desired Idle
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1231 Fuel Pump Relay Contact Problem
- Table 2 - Trouble Code Table: Trouble Code 55
- F0:Data List - Test Step 35 Knock Rtd. Cyl. 4
- F0: Data List - Test Step 33 Injection Pulse
- F0:Data List Test Step 36 Des. Idle Adjust
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1405 Linear EGR Position
- Table 3 - Control Unit Coding
- How to Check the Table 1, Diagnostic Plug (Aldl) and Voltage Supply
- F0:Data List - Test Step 36 Injection Pulse
- F0: Data List - Test Step 34 Spark Advance
- F0:Data List Test Step 37 Idle Adjust
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1410 Second. Air Pump Relay Voltage High
- Table 3 - Octane Number Plug Coding
- Table 2, Multec-M (14 Se/C 14SE/C 16 SE) F2:Trouble Code
- F0:Data List - Test Step 37 Spark Advance
- F0: Data List - Test Step 35 Fuel Pump Relay
- F0:Data List Test Step 38 Desired Idle P-N
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1410 Second. Air Pump Relay Voltage Low
- Table 4 - Engine Does Not Start
- Table 2, Trouble Code Table (TC 13 O2 Sensor Open Circuit)
- F0:Data List - Test Step 38 Diag. Request
- F0: Data List - Test Step 36 Diag. Request
- F0:Data List Test Step 39 Idle Adjust P-N
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1501 Immobiliser No or Wrong Coding
- Table 5 - Test Step 01 Check Fuel Injector
- Table 2, Trouble Code Table (TC 14 Coolant Temperature Voltage Low)
- F0:Data List - Test Step 39 Idle Adjust
- F0: Data List - Test Step 37 Spark Table 91
- F0:Data List Test Step 40 Des. Idle Drive
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1502 Immobiliser No Signal
- Table 5 - Test Step 02 Check Idle Air Control Valve
- Table 2, Trouble Code Table (TC 15 Coolant Temperature Voltage High)
- F0:Data List - Test Step 40 Des. Idle Adjust
- F0: Data List - Test Step 38 Spark Table 95
- F0:Data List Test Step 41 Idle Adjust Drive
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1503 Immobiliser Wrong Signal
- Table 5 - Test Step 03 Check Ignition Spark
- Table 2, Trouble Code Table (TC 19 Incorrect RPM Signal)
- F0:Data List - Test Step 41 Idle Adjust
- F0: Dtenliste - Test Step 39 Des. Idle Adjust
- F0:Data List Test Step 42 Iac Cntr. Enable
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1530 A/c Cutoff Relay Voltage High
- Table 2, Trouble Code Table (TC 21 Throttle Posit. Sensor Voltage High)
- F0:Data List - Test Step 42 Injector Cutoff
- F0: Data List - Test Step 40 Idle Adjust
- F0:Data List Test Step 43 Idle Air Control
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1530 A/c Cutoff Relay Voltage Low
- Checking of Fuel Pump Relay
- Table 2, Trouble Code Table (TC 22 Throttle Posit. Sensor Voltage Low)
- How to Check the Table 1, Diagnostic Plug and Voltage Feed
- F0: Data List - Test Step 41 Desired Idle P-N
- F0:Data List Test Step 44 Injection Pulse
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1602 Knock Control Module; Replace ECU
- Terminal Assignment of Control Unit
- Table 2, Trouble Code Table (TC 24 No Vehicle Speed Signal)
- Table 2, Multec-S (C 16 XE) F2:Trouble Code
- F0: Data List - Test Step 42 Idle Adjust P-N
- F0:Data List Test Step 45 Engine Load
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1604 Replace ECU
- Table 2, Trouble Code Table (TC 25 Injector Valve Voltage Low)
- F2:Trouble Code Table - Trouble Code 13 - O2 Sensor Open Circuit
- F0: Data List - Test Step 43 Des. Idle Drive
- F0:Data List Test Step 46 Vehicle Sp.pulse
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1605 Reprogram or Replace ECU
- Table 2, Trouble Code Table (TC 29 Fuel Pump Relay Voltage Low)
- F2:Trouble Code Table - Trouble Code 14 - Coolant Temperature Voltage Low
- F0: Data List - Test Step 44 Idle Adjust Drive
- F0:Data List Test Step 47 Vehicle Speed
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1640 Quad Driver Module (Qdm)
- Table 2, Trouble Code Table (TC 32 Fuel Pump Relay Voltage High)
- F2:Trouble Code Table - Trouble Code 15 - Coolant Temperature Voltage High
- How to Check the Table 1, Diagnostic Plug and Voltage Supply
- F0:Data List Test Step 48 Torque Control
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1740 Torque Control Voltage Low
- F2:Trouble Code Table - Trouble Code 16 - Knock Signal Circuit
- Table 2, Multec (X 12 SZ / X 16 SZ) F2: Trouble Code
- F0:Data List Test Step 49 Power Enrichment
- B-02, F2: Diagnostic Trouble Code Table Trouble Code P1740 Continuous Torque Control
- Table 2, Trouble Code Table (TC 34 MAP Sensor Voltage Low)
- F2:Trouble Code Table - Trouble Code 18 - Knock Filter Module
- F2:Trouble Code Table - Trouble Code 13 O2 Sensor Open Circuit
- F0:Data List Test Step 50 A/c Relay
- B-03, F0: Data List Test Step T01 Battery Voltage
- Table 2, Trouble Code Table (TC 35 Idle Air Control)
- F2:Trouble Code Table - Trouble Code 19 - Incorrect RPM Signal
- F2:Trouble Code Table - Trouble Code 14 Coolant Temperature Voltage Low
- F0:Data List Test Step 51 Dec. Fuel Cutoff
- B-03, F0: Data List Test Step T02 Immobiliser
- Table 2, Trouble Code Table (TC 41 Est Line Coil Cyl 2+3 Voltage High)
- F2:Trouble Code Table - Trouble Code 21 - Throttle Posit. Sensor Voltage High
- F2:Trouble Code Table - Trouble Code 15 Coolant Temperature Voltage High
- F0:Data List Test Step 52 Injector Cutoff
- B-03, F0: Data List Test Step T03 Immobiliser Sig.
- F2:Trouble Code Table - Trouble Code 22 - Throttle Posit. Sensor Voltage Low
- F2:Trouble Code Table - Trouble Code 16 Knock Signal Circuit
- Additional Fault Diagnosis - No.01 Camshaft Sensor
- B-03, F0: Data List Test Step T04 FUEL Pump Relay
- Table 2, Trouble Code Table (TC 42 Est Line Coil Cyl 1+4 Voltage High)
- F2:Trouble Code Table - Trouble Code 24 - No Vehicle Speed Signal
- F2:Trouble Code Table - Trouble Code 18 Knock Control System
- Additional Fault Diagnosis - No.02 Fuel Consumption Signal
- B-03, F0: Data List Test Step T05 TPS Signal
- Table 2, Trouble Code Table (TC 44 Lean Exhaust)
- F2:Trouble Code Table - Trouble Code 25 - Injector Valve Voltage Low
- F2:Trouble Code Table - Trouble Code 19 Incorrect RPM Signal
- Table 3, Control Unit Coding
- B-03, F0: Data List Test Step T06 MAP Sensor
- Table 2, Trouble Code Table (TC 45 Rich Exhaust)
- F2:Trouble Code Table - Trouble Code 28 - Fuel Pump Relay Contact Problem
- F2:Trouble Code Table - Trouble Code 21 Throttle Posit. Sensor Voltage High
- F2:Trouble Codes - Trouble Code No. 13 O2 Sensor Open Circuit
- B-03, F0: Data List Test Step T07 Coolant Temperature
- F2:Trouble Code Table - Trouble Code 29 - Fuel Pump Relay Voltage Low
- F2:Trouble Code Table - Trouble Code 22 Throttle Posit. Sensor Voltage Low
- F2:Trouble Codes - Trouble Code No. 14 Coolant Temperature Voltage Low
- B-03, F0: Data List Test Step T08 Intake Air Temperature
- Table 2, Trouble Code Table (TC 51 Replace ECU or Prom)
- F2:Trouble Code Table - Trouble Code 32 - Fuel Pump Relay Voltage High
- F2:Trouble Code Table - Trouble Code 24 No Vehicle Speed Signal
- F2:Trouble Codes - Trouble Code No. 15 Coolant Temperature Voltage High
- B-03, F0: Data List Test Step T09 Transm. Coding
- Table 2, Trouble Code Table (TC 55 Replace ECU)
- F2:Trouble Code Table - Trouble Code 35 - Idle Air Control
- F2:Trouble Code Table - Trouble Code 25 Injector Valve Voltage Low
- F2:Trouble Codes - Trouble Code No. 16 Knock Signal Circuit
- B-03, F0: Data List Test Step T10 PARK/neutral Sw.
- Table 2, Trouble Code Table (TC 63 Est Line Coil Cyl 2+3 Voltage Low)
- F2:Trouble Code Table - Trouble Code 44 - Lean Exhaust
- F2:Trouble Code Table - Trouble Code 29 Fuel Pump Relay Voltage Low
- F2:Trouble Codes - Trouble Code No. 17 Fuel Injector Circuit(s)
- B-03, F0: Data List Test Step T11 A/c Informat. Sw
- Ight Idle Speed, Jerking at Partial Load
- F2:Trouble Code Table - Trouble Code 45 - Rich Exhaust
- F2:Trouble Code Table - Trouble Code 32 Fuel Pump Relay Voltage High
- F2:Trouble Codes - Trouble Code No. 18 Knock Filter Module
- B-03, F0: Data List Test Step T12 A/c Load Signal
- Table 2, Trouble Code Table (TC 64 Est Line Coil Cyl 1+4 Voltage Low)
- F2:Trouble Code Table - Trouble Code 46 - Est Line(s) Voltage High
- F2:Trouble Code Table - Trouble Code 33 MAP Sensor Voltage High
- F2:Trouble Codes - Trouble Code No. 19 Incorrect RPM Signal
- B-03, F0: Data List Test Step T13 Injection Pulse
- Table 2, Trouble Code Table (TC 69 Intake Air Temperature Voltage Low)
- F2:Trouble Code Table - Trouble Code 49 - Battery Voltage High
- F2:Trouble Code Table - Trouble Code 34 MAP Sensor Voltage Low
- F2:Trouble Codes - Trouble Code No. 21 Throttle Posit. Sensor Voltage High
- B-03, F0: Data List Test Step T14 Clear Flood Mode
- Table 2, Trouble Code Table (TC 71 Intake Air Temperature Voltage High)
- F2:Trouble Code Table - Trouble Code 51 - Replace ECU or Prom
- F2:Trouble Code Table - Trouble Code 35 Idle Air Control
- F2:Trouble Codes - Trouble Code No. 22 Throttle Posit. Sensor Voltage Low
- B-03, F0: Data List Test Step T15 Spark Advance
- Table 2, Trouble Code Table (TC 75 Torque Control Voltage Low)
- F2:Trouble Code Table - Trouble Code 55 - Replace ECU
- F2:Trouble Code Table - Trouble Code 41 Est Line Coil Cyl 2+3 Voltage High
- F2:Trouble Codes - Trouble Code No. 24 No Vehicle Speed Signal
- B-03, F0: Data List Test Step T16 Knock Cell No.
- Table 2, Trouble Code Table (TC 76 Continuous Torque Control)
- F2:Trouble Code Table - Trouble Code 63 - Est Line Coil Cyl 2+3 Voltage Low
- F2:Trouble Code Table - Trouble Code 42 Est Line Coil Cyl 1+4 Voltage High
- F2:Trouble Codes - Trouble Code No. 28 Fuel Pump Relay Contact Problem
- B-03, F0: Data List Test Step T17 Knock Rtd. cyl.1
- List of Vehicle Systems That CAN Be Checked with Tech 2 - Techline
- Table 2, Trouble Code Table (TC 81 Injector Valve Voltage High)
- F2:Trouble Code Table - Trouble Code 64 - Est Line Coil Cyl 1+4 Voltage Low
- F2:Trouble Code Table - Trouble Code 43 Linear EGR System
- F2:Trouble Codes - Trouble Code No. 29 Fuel Pump Relay Voltage Low
- B-03, F0: Data List Test Step T18 Knock Rtd. cyl.2
- Table 2, Trouble Code Table (TC 93 Quad Driver Module (Qdm))
- F2:Trouble Code Table - Trouble Code 67 - Mass Air Flow Sensor Range
- F2:Trouble Code Table - Trouble Code 44 Lean Exhaust
- F2:Trouble Codes - Trouble Code No. 32 Fuel Pump Relay Voltage High
- B-03, F0: Data List Test Step T19 Knock Rtd. cyl.3
- Table 3, Coding of Control Units (Survey of Control Units)
- F2:Trouble Code Table - Trouble Code 68 - Mass Air Flow Sensor Frequency
- F2:Trouble Code Table - Trouble Code 45 Rich Exhaust
- F2:Trouble Codes - Trouble Code No. 33 MAP Sensor Voltage High
- B-03, F0: Data List Test Step T20 Knock Rtd. cyl.4
- Table 3, Coding of Octane Number Plugs
- F2:Trouble Code Table - Trouble Code 72 - Est Line(s) Open Circuit
- F2:Trouble Code Table - Trouble Code 47 Linear EGR Position
- F2:Trouble Codes - Trouble Code No. 34 MAP Sensor Voltage Low
- B-03, F0: Data List Test Step T21 SEC.air Pump Rel
- Table 4, Engine Does Not Start
- F2:Trouble Code Table - Trouble Code 81 - Injector Valve Voltage High
- F2:Trouble Code Table - Trouble Code 49 Battery Voltage High
- F2:Trouble Codes - Trouble Code No. 35 Idle Air Control
- B-03, F0: Data List Test Step T22 AIR Control Sol.
- After Engine Starting, Greatly Increased Idle Speed
- Table 5, F5:Actuator Test Test Step 01 Idle Air Control
- F2:Trouble Code Table - Trouble Code 92 - Hall Sensor Circuit
- F2:Trouble Code Table - Trouble Code 51 Replace ECU or Prom
- F2:Trouble Codes - Trouble Code No. 41 Est Line Coil Cyl 2+3 Voltage High
- B-03, F0: Data List Test Step T23 EGR Position Cmd
- Table 5, F5:Actuator Test Test Step 02 Fuel Pump Relay
- F2:Trouble Code Table - Trouble Code 93 - Quad Driver Module (Qdm)
- F2:Trouble Code Table - Trouble Code 55 Replace ECU
- F2:Trouble Codes - Trouble Code No. 42 Est Line Coil Cyl 1+4 Voltage High
- B-03, F0: Data List Test Step T24 EGR Pos. Fdbk
- Table 5, F5:Actuator Test Test Step 03 Quad Driver Test
- Table 3, Coding of Control Units
- F2:Trouble Code Table - Trouble Code 63 Est Line Coil Cyl 2+3 Voltage Low
- F2:Trouble Codes - Trouble Code No. 43 Linear EGR System
- B-03, F0: Data List Test Step T25 FUEL Tank Vent.
- Table 5, F5:Actuator Test Test Step 04 Ignition Spark
- F2:Trouble Code Table - Trouble Code 64 Est Line Coil Cyl 1+4 Voltage Low
- F2:Trouble Codes - Trouble Code No. 44 Lean Exhaust
- B-03, F0: Data List Test Step T26 O2 Sensor
- Table 5, F5:Actuator Test Test Step 05 Ign. Coil CYL1-4 Frequency 2/sec
- F5:actuator Test Select Actuator Idle Air Control
- F2:Trouble Code Table - Trouble Code 75 Torque Control Voltage Low
- F2:Trouble Codes - Trouble Code No. 45 Rich Exhaust
- B-03, F0: Data List Test Step T27 AIR/fuel Ratio
- Table 5, F5:Actuator Test Test Step 06 Ign. Coil CYL1+4 Frequency 2/sec
- F5:actuator Test Select Actuator Quad Driver Test
- F2:Trouble Code Table - Trouble Code 76 Continuous Torque Control
- F2:Trouble Codes - Trouble Code No. 47 Linear EGR Position
- B-03, F0: Data List Test Step T28 O2 Sensor Loop
- Table 5, F5:Actuator Test Test Step 07 Ign. Coil CYL2+3 Frequency 2/sec
- F5:actuator Test Select Actuator Ign. Coil cyl1+4
- F2:Trouble Code Table - Trouble Code 81 Injector Valve Voltage High
- F2:Trouble Codes - Trouble Code No. 49 Battery Voltage High
- B-03, F0: Data List Test Step T29 AIR/fuel Status
- Table 5, F5:Actuator Test Test Step 08 A/c Relay
- F5:actuator Test Select Actuator Ign. Coil cyl2+3
- F2:Trouble Code Table - Trouble Code 93 Quad Driver Module (Qdm)
- F2:Trouble Codes - Trouble Code No. 51 Replace ECU or Prom
- B-03, F0: Data List Test Step T30 O2 Integrator
- Table 6, F6:Adjustments CO Adjustments (See Checking Procedures)
- F5:actuator Test Select Actuator Fuel Pump Relay
- F2:Trouble Codes - Trouble Code No. 52 Second. Air Pump Relay Voltage Low
- B-03, F0: Data List Test Step T31 O2 Blm Enable
- Engine Stalls, Surges at Idle Speed, Jerks and Pings
- Table 8, F8:ECU Control RPM Control
- F5:actuator Test Select Actuator A/c Relay
- F2:Trouble Codes - Trouble Code No. 53 Second. Air Pump Relay Voltage High
- B-03, F0: Data List Test Step T32 O2 Blm Cell No.
- Table 8, Trouble-Shooting Chart
- F5:actuator Test Select Actuator Fuel Tank Vent
- Quick Check F5:Actuator Test No. 01 Select Actuator Idle Air Control
- F2:Trouble Codes - Trouble Code No. 55 Replace ECU
- B-03, F0: Data List Test Step T33 O2 Blm Cell Cont
- Terminal Assignment of Diagnostic Plug X 13
- Multec-S (C 16 XE) F6:Miscellaneous Tests
- Quick Check F5:Actuator Test No. 02 Select Actuator Quad Driver Test
- F2:Trouble Codes - Trouble Code No. 56 Air Control Sol. Voltage Low
- B-03, F0: Data List Test Step T34 Engine Speed
- F6:miscellaneous Tests f0:adjustments Idle Adjust
- Quick Check F5:Actuator Test No. 03 Select Actuator Ign. Coil cyl1+4
- F2:Trouble Codes - Trouble Code No. 57 Air Control Sol. Voltage High
- B-03, F0: Data List Test Step T35 IAC Cntr. Enable
- F6:miscellaneous Tests f1:control Unit Reset Select Reset Idle Adjust
- Quick Check F5:Actuator Test No. 04 Select Actuator Ign. Coil cyl2+3
- F2:Trouble Codes - Trouble Code No. 61 Fuel Tank Vent. Valve Voltage Low
- B-03, F0: Data List Test Step T36 IDLE Air Control
- F6:miscellaneous Tests f1:control Unit Reset Select Reset o2 Blm Cells
- Quick Check F5:Actuator Test No. 05 Select Actuator Fuel Pump Relay
- F2:Trouble Codes - Trouble Code No. 62 Fuel Tank Vent. Valve Voltage High
- B-03, F0: Data List Test Step T37 Desired Idle
- F6:miscellaneous Tests f1:control Unit Reset Select Reset Iac Blm Cells
- Quick Check F5:Actuator Test No. 06 Select Actuator Fuel Injector
- F2:Trouble Codes - Trouble Code No. 63 Est Line Coil Cyl 2+3 Voltage Low
- B-03, F0: Data List Test Step T38 IDLE Adjust
- F6:miscellaneous Tests f1:control Unit Reset Select Reset Knock Cells
- Quick Check F5:Actuator Test No. 07 Select Actuator Fuel Tank Vent.
- F2:Trouble Codes - Trouble Code No. 64 Est Line Coil Cyl 1+4 Voltage Low
- Multec X 12 SZ Introductory Summary
- B-03, F0: Data List Test Step T39 Engine Load
- Quick Check F8:ECU Control RPM Control
- F6:miscellaneous Tests
- F2:Trouble Codes - Trouble Code No. 66 Broken Throttle Position Sensor Hose
- Multec X 12 SZ - Allocation of Components in Vehicle
- B-03, F0: Data List Test Step T40 Torque Control
- Terminal Assignment X4 (Corsa-B MJ'93,5)
- Table 8, Trouble Shooting Chart
- F0:adjustments
- F2:Trouble Codes - Trouble Code No. 69 Intake Air Temperature Voltage Low
- Multec X 12 SZ - Purpose and Function of System
- B-03, F0: Data List Test Step T41 A/c Relay
- Terminal Assignment - Control Unit
- F1:ecu Reset
- F2:Trouble Codes - Trouble Code No. 71 Intake Air Temperature Voltage High
- Multec X 12 SZ - Block Diagram
- B-03, F0: Data List Test Step T42 Vehicle Sp.pulse
- Terminal Assignment X 5, X 16, X 28 (Corsa-B MJ'93,5)
- Circuit Diagram and Part Locations
- F6:Miscellaneous Tests No. 01 Idle Adjust
- F2:Trouble Codes - Trouble Code No. 75 Torque Control Voltage Low
- Control Unit
- B-03, F0: Data List Test Step T43 Vehicle Speed
- Legend for Circuit Diagram C 16 XE MY 93.5
- F6:Miscellaneous Tests No. 02 Idle Adjust Drive
- F2:Trouble Codes - Trouble Code No. 76 Continuous Torque Control
- Direct Ignition System
- B-03, F0: Data List Test Step T44 Check Light
- Time Allowance
- F6:Miscellaneous Tests No. 03 Idle Adjust P-N
- F2:Trouble Codes - Trouble Code No. 83 Immobiliser No or Wrong Coding
- Controlled Canister Purge Valve
- B-03, F0: Data List Test Step T45 Blinkcode Req.
- F6:Miscellaneous Tests No.03 Select Reset Idle Adjust P-N
- F2:Trouble Codes - Trouble Code No. 84 Immobiliser No Signal
- Intake Manifold Absolute Pressure Sensor
- B-03, F0: Data List Test Step T46 DEC. Fuel Cutoff
- F2:Trouble Codes - Trouble Code No. 85 Immobiliser Wrong Signal
- Oxygen Sensor
- B-03, F0: Data List Test Step T47 Power Enrichment
- F2:Trouble Codes - Trouble Code No. 87 A/c Cutoff Relay Voltage Low
- Linear Exhaust Gas Recirculation Valve
- B-03, F0: Data List Test Step T48 Injector Cutoff
- Terminal Assignment
- F2:Trouble Codes - Trouble Code No. 88 A/c Cutoff Relay Voltage High
- Knock Control System
- B-04, F1: Exhaust Gas Test Test Step T07 Coolant Temperature
- Parts Locations for Corsa-B X 12 SZ MY '93.5
- F2:Trouble Codes - Trouble Code No. 92 Hall Sensor Circuit
- B-04, F1: Exhaust Gas Test Test Step T26 O2 Sensor
- F2:Trouble Codes - Trouble Code No. 93 Quad Driver Module (Qdm)
- Throttle Valve Potentiometer
- B-04, F1: Exhaust Gas Test Test Step T28 O2 Sensor Loop
- Circuit Diagram Corsa-B X 12 SZ MY '93.5
- Quick Check F5:Actuator Test Idle Air Contr
- Idle Speed Stepper Motor
- B-05, F5: Actuator Test Test Step T01 IMMO.sig. Test
- Quick Check F5:Actuator Test Fuel Pump Rel.
- Coolant Temperature Sensor
- B-05, F5: Actuator Test Test Step T02 FUEL Pump Rel.
- Quick Check F5:Actuator Test Ign. Coil 1+4
- Diagnosis Plug
- B-05, F5: Actuator Test Test Step T03 IGN. Coil 1+4
- Quick Check F5:Actuator Test Ign. Coil 2+3
- Circuit Diagram, Multec X 12 SZ
- B-05, F5: Actuator Test Test Step T04 IGN. Coil 2+3
- Quick Check F5:Actuator Test Quad Driver T.
- Terminal Assign. of Wiring Harness Plug
- B-05, F5: Actuator Test Test Step T05 EGR Puls.ratio
- Quick Check F5:Actuator Test Inj.circuit T.
- Trouble Code Table
- B-05, F5: Actuator Test Test Step T06 FUEL Tank Vent
- Circuit Diagram Corsa-B, MY'93.5/C 14 SE Multec-M
- Quick Check F5:Actuator Test Fuel Tank Vent
- B-05, F5: Actuator Test Test Step T07 IDLE Air Contr
- Circuit Diagram Corsa-B, MY'93.5/C 16 SE Starter
- Quick Check F5:Actuator Test A/c Relay
- B-05, F5: Actuator Test Test Step T08 A/c Relay
- Quick Check F5:Actuator Test Air Contr. Sol
- B-05, F5: Actuator Test Test Step T09 QUAD Driver T.
- Quick Check F5:Actuator Test Sec. Air P.rel
- B-05, F5: Actuator Test Test Step T10 INJ.circuit T.
- Quick Check F5:Actuator Test Immo.sig. Test
- B-05, F5: Actuator Test Test Step T11 AIR Contr. Sol
- Quick Check F5:Actuator Test Linear EGR
- B-05, F5: Actuator Test Test Step T12 SEC. Air P.rel
- F6:Miscellaneous Tests (F0:Adjustments/F1:ECU Reset)
- B-05, F5: Actuator Test Test Step T13 Check Light
- F6:Miscellaneous Tests F0:Adjustments Idle Adjust (Mt Vehicles)
- B-06, F6: Additional Functions Test Step T01 READ ECU ID
- F6:Miscellaneous Tests F0:Adjustments Idle Adjustdrive (At Vehicles)
- B-06, F6: Additional Functions Test Step T02 READ VIN
- F6:Miscellaneous Tests F0:Adjustments Idle Adjust P-N (At Vehicles)
- Multec-S - Introduction
- B-06, F6: Additional Functions Test Step T03 ADJ.idle Speed
- F6:Miscellaneous Tests F1:Reset O2 Blm Cells
- Multec-S - Diagnosis
- B-06, F6: Additional Functions Test Step T04 ADJ.idle Drive
- F6:Miscellaneous Tests F1:Reset Iac Blm Cells
- Multec-S - Read Trouble Code
- B-06, F6: Additional Functions Test Step T05 ADJ.idle P/n
- F6:Miscellaneous Tests F1:Reset Knock Cells
- Multec-S - Check Data List Parameters
- B-06, F6: Additional Functions Test Step T06 RES. Idle Adjust
- F6:Miscellaneous Tests F1:Reset Idle Adjust
- Multec-S - Carry Out Actuator Tests
- B-06, F6: Additional Functions Test Step T07 Reset Knockmap
- F7:Programming Immobiliser
- Multec-S C 16 XE - General
- Multec-S - Carry Out Control Tests
- B-06, F6: Additional Functions Test Step T08 Reset o2 Blm
- F8:ECU Control RPM Control
- Multec-S C 16 XE-Survey of Engine Compartment
- Multec-S - Snapshot Mode
- B-06, F6: Additional Functions Test Step T09 Reset Iac Blm
- F8:ECU Control Inj.control
- Multec-S C 16 XE - Survey of System
- Multec-S - Final System Test
- B-07, F7: Programming Test Step T01 Control Module
- Multec-S C 16 XE - Block Diagram
- Multec-S - General Safety Measures and Repair Instructions
- B-07, F7: Programming Test Step T02 Immobiliser
- Survey of Vehicle
- B-08, F8: ECU Control Test Test Step T01 INJ.control
- Exhaust Emissions Test F1:Circuit Test No.07 - Coolant Temperature
- Multec-S C 16 XE - Circuit Diagram
- F2: Trouble Code Table - Trouble Code 13 O2 Sensor Open Circuit
- B-08, F8: ECU Control Test Test Step T02 EGR Control
- Exhaust Emissions Test F1:Circuit Test No.28 - O2 Sensor Loop
- Terminal Assignment of Engine Control Unit Wiring Harness Plug
- F2: Trouble Code Table - Trouble Code 14 Coolant Temperature Voltage Low
- B-08, F8: ECU Control Test Test Step T03 RPM Control
- Exhaust Emissions Test F1:Circuit Test No.27 - O2 Sensor
- Hot-Wire Mass Air Flow Meter
- F2: Trouble Code Table - Trouble Code 15 Coolant Temperature Voltage High
- B-08, F8: ECU Control Test Test Step T04 IAC Control
- F2: Trouble Code Table - Trouble Code 16 Knock Signal Circuit
- B-09, Engine Does Not Start
- Excerpt from Circuit Diagram Corsa- B, Tigra
- Cylinder Recognition
- F2: Trouble Code Table - Trouble Code 17 Fuel Injector Circuit(s)
- C-01, No Communication Between Diagnostic Tester and Control Unit
- F2: Trouble Code Table - Trouble Code 18 Knock Filter Module
- C-02, Control Unit Hard- and Software
- Dis - Direct Ignition System
- F2: Trouble Code Table - Trouble Code 19 Incorrect RPM Signal
- C-03, System Voltage Circuit
- Controlled Canister Purge System
- F2: Trouble Code Table - Trouble Code 21 Throttle Posit. Sensor Voltage High
- C-04, Immobiliser Signal Circuit
- Fuel System
- F2: Trouble Code Table - Trouble Code 22 Throttle Posit. Sensor Voltage Low
- C-05, Fuel Pump Relay Circuit
- Multec-S C 16 XE - Trouble Code Table
- F2: Trouble Code Table - Trouble Code 24 No Vehicle Speed Signal
- C-06, Throttle/pedal Position Sensor/switch a Circuit
- Quad Driver Test
- F2: Trouble Code Table - Trouble Code 28 Fuel Pump Relay Contact Problem
- C-07, Manifold Absolute Pressure Solenoid Circuit
- Diagnosis with Tech 1
- F2: Trouble Code Table - Trouble Code 29 Fuel Pump Relay Voltage Low
- C-08, Engine Coolant Temperature Sensor Circuit
- F2: Trouble Code Table - Trouble Code 32 Fuel Pump Relay Voltage High
- C-09, Intake Air Temperature Sensor Circuit
- Multec-M C 14 SE - Introductory Summary
- F2: Trouble Code Table - Trouble Code 33 MAP Sensor Voltage High
- C-10, Park/neutral Switch Circuit
- Multec-M C 14 SE - Allocation of Components in Vehiclpф=
- F2: Trouble Code Table - Trouble Code 34 MAP Sensor Voltage Low
- C-11, Air Conditioning System Information Switch Circuit
- Multec-M C 14 SE - Block Diagram
- F2: Trouble Code Table - Trouble Code 35 Idle Air Control
- C-12, Air Conditioning System Load Signal Circuit
- Multec-M C 14 SE - Control Unit
- F2: Trouble Code Table - Trouble Code 41 Est Line Coil Cyl 2+3 Voltage High
- C-13, Camshaft Position Sensor Circuit
- F2: Trouble Code Table - Trouble Code 42 Est Line Coil Cyl 1+4 Voltage High
- C-14, Engine-Compression
- Controlled Canister Purge System C 14 SE
- F2: Trouble Code Table - Trouble Code 43 Linear EGR System
- C-15, Ignition Timing
- F2: Trouble Code Table - Trouble Code 44 Lean Exhaust
- C-16, Ignition Coil a Primary/secondary Circuit
- F2: Trouble Code Table - Trouble Code 45 Rich Exhaust
- C-17, Ignition Coil B Primary/secondary Circuit
- Engine Telltale Illum. Fc P0325 Is Exch. Exch. of Knock Sensor Not Successful
- Intake Air Temperature Sensor
- F2: Trouble Code Table - Trouble Code 47 Linear EGR Position
- C-18, Injector Circuit
- Octane Number Plug
- F2: Trouble Code Table - Trouble Code 49 Battery Voltage High
- C-19, Knock Sensor 1 Circuit
- Throttle Body
- F2: Trouble Code Table - Trouble Code 51 Replace ECU or Prom
- C-20, Secondary Air Pump Circuit
- F2: Trouble Code Table - Trouble Code 52 Second. Air Pump Relay Voltage Low
- C-21, Secondary Air Injection System Switching Valve a Circuit
- F2: Trouble Code Table - Trouble Code 53 Second. Air Pump Relay Voltage High
- C-22, Linear Exhaust Gas Recirculation Valve Circuit
- F2: Trouble Code Table - Trouble Code 55 Replace ECU
- C-23, Exhaust Gas Recirculation Sensor Circuit
- Diagnostic Plug
- F2: Trouble Code Table - Trouble Code 56 Air Control Sol. Voltage Low
- C-24, Evaporative Emission Control System Circuit
- F2: Trouble Code Table - Trouble Code 57 Air Control Sol. Voltage High
- C-25, O2 Sensor Circuit
- Multec-M C 14 SE - Circuit Diagram
- F2: Trouble Code Table - Trouble Code 61 Fuel Tank Vent. Valve Voltage Low
- C-26, Crankshaft Sensor Circuit
- Terminal Assignment, Wiring Harness Plug
- F2: Trouble Code Table - Trouble Code 62 Fuel Tank Vent. Valve Voltage High
- C-27, Idle Speed Actuator Circuit
- Multec-M C 14 SE - Trouble Code Table
- F2: Trouble Code Table - Trouble Code 63 Est Line Coil Cyl 2+3 Voltage Low
- C-28, Engine Speed Output Signal Circuit
- F2: Trouble Code Table - Trouble Code 64 Est Line Coil Cyl 1+4 Voltage Low
- C-29, Engine Load Signal Circuit
- F2: Trouble Code Table - Trouble Code 66 Broken Throttle Position Sensor Hose
- C-30, Torque Control Circuit
- F2: Trouble Code Table - Trouble Code 69 Intake Air Temperature Voltage Low
- C-31, Air Conditioning System Relay Circuit
- F2: Trouble Code Table - Trouble Code 71 Intake Air Temperature Voltage High
- C-32, Vehicle Speed Sensor Circuit
- F2: Trouble Code Table - Trouble Code 75 Torque Control Voltage Low
- C-33, Malfunction Indication Lamp (MIL) Circuit
- F2: Trouble Code Table - Trouble Code 76 Continuous Torque Control
- C-34, Blinkcode Request Circuit
- F2: Trouble Code Table - Trouble Code 83 Immobiliser No or Wrong Coding
- C-35, Duration of Injection
- F2: Trouble Code Table - Trouble Code 84 Immobiliser No Signal
- C-36, Deceleration Fuel Cutoff Circuit
- F2: Trouble Code Table - Trouble Code 85 Immobiliser Wrong Signal
- C-37, Power Enrichment Circuit
- F2: Trouble Code Table - Trouble Code 87 A/c Cutoff Relay Voltage Low
- C-38, Fuel Consumption Signal Circuit
- F2: Trouble Code Table - Trouble Code 88 A/c Cutoff Relay Voltage High
- C-39, Quad Driver Module (Qdm) Circuit
- F2: Trouble Code Table - Trouble Code 92 Hall Sensor Circuit
- C-40, Throttle/pedal Hose
- F2: Trouble Code Table - Trouble Code 93 Quad Driver Module (Qdm)
- Parts Location
- F0: Data List - Test Step 02 Diag. Request
- Wiring Schematic Diagram
- F0: Data List - Test Step 03 Immobiliser
- F0: Data List - Test Step 04 Immobiliser Sig.
- F0: Data List - Test Step 05 TPS Signal
- F0: Data List - Test Step 06 MAP Sensor
- F0: Data List - Test Step 07 Coolant Temperature
- F0: Data List - Test Step 08 Intake Air Temperature
- Trouble Code Table; Engine Control Units
- F0: Data List - Test Step 09 A/c Informat. Sw
- F0: Data List - Test Step 10 A/c Load Signal
- F0: Data List - Test Step 11 Park/neutral Sw.
- F0: Data List - Test Step 12 Fuel Pump Relay
- F0: Data List - Test Step 13 Clear Flood Mode
- F0: Data List - Test Step 14 Spark Advance
- F0: Data List - Test Step 15 Knock Voltage
- F0: Data List - Test Step 16 Knock Pulses
- F0: Data List - Test Step 17 Knock Cell No.
- F0: Data List - Test Step 18 Knock Rtd. Cyl. 1
- F0: Data List - Test Step 19 Knock Rtd. Cyl. 2
- F0: Data List - Test Step 20 Knock Rtd. Cyl. 3
- F0: Data List - Test Step 21 Knock Rtd. Cyl. 4
- F0: Data List - Test Step 22 Sec. Air Pump Rel
- F0: Data List - Test Step 23 Air Control Sol.
- F0: Data List - Test Step 24 EGR Position Cmd
- F0: Data List - Test Step 25 EGR Pos. Fdbk
- F0: Data List - Test Step 26 Fuel Tank Vent.
- F0: Data List - Test Step 27 O2 Sensor
- F0: Data List - Test Step 28 O2 Sensor Loop
- F0: Data List - Test Step 29 Air/fuel Ratio
- F0: Data List - Test Step 30 O2 Integrator
- F0: Data List - Test Step 31 O2 Blm Enable
- F0: Data List - Test Step 32 O2 Blm Cell No.
- F0: Data List - Test Step 33 O2 Blm Cell Cont
- F0: Data List - Test Step 34 Engine Speed
- F0: Data List - Test Step 35 Desired Idle
- When Re-Programming Control Unit, Trouble Message TC0635 or 0637 Is Displayed.
- F0: Data List - Test Step 36 Des. Idle Adjust
- F0: Data List - Test Step 37 Idle Adjust
- F0: Data List - Test Step 38 Desired Idle P-N
- F0: Data List - Test Step 39 Idle Adjust P-N
- F0: Data List - Test Step 40 Des. Idle Drive
- F0: Data List - Test Step 41 Idle Adjust Drive
- F0: Data List - Test Step 42 Iac Cntr. Enable
- F0: Data List - Test Step 43 Idle Air Control
- F0: Data List - Test Step 44 Injection Pulse
- F0: Data List - Test Step 45 Engine Load
- F0: Data List - Test Step 46 Vehicle Sp. Pulse
- F0: Data List - Test Step 47 Vehicle Speed
- F0: Data List - Test Step 48 Torque Control
- F0: Data List - Test Step 49 Power Enrichment
- F0: Data List - Test Step 50 A/c Relay
- F0: Data List - Test Step 51 Dec. Fuel Cutoff
- F0: Data List - Test Step 52 Injector Cutoff
- F1: Control Circuit Test - Number 07 Coolant Temperature
- F1: Control Circuit Test - Number 28 O2 Sensor Loop
- F1: Control Circuit Test - Number 27 O2 Sensor
- F5: Actuator Test - Number 1 Idle Air Control
- F5: Actuator Test - Number 2 Fuel Pump Rel.
- F5: Actuator Test - Number 3 Ign. Coil 1+4
- F5: Actuator Test - Number 4 Ign. Coil 2+3
- F5: Actuator Test - Number 5 Quad Driver T.
- F5: Actuator Test - Number 6 Inj. Circuit T.
- F5: Actuator Test - Number 7 Fuel Tank Vent.
- F5: Actuator Test - Number 8 A/c Relay
- F5: Actuator Test - Number 9 Air Contr. Sol
- F5: Actuator Test - Number 10 Sec. Air P. Rel
- F5: Actuator Test - Number 11 Immo. Sig. Test
- F5: Actuator Test - Number 12 Linear EGR
- F6: Miscellaneous Tests; F0: Adjustments Idle Adjust (Mt Vehicles Only)
- F6: Miscellaneous Tests; F0: Adjustments Idle Adjust Drive (At Vehicles Only)
- F6: Miscellaneous Tests; F0: Adjustments Idle Adjust P-N (At Vehicles Only)
- F6: Miscellaneous Tests; f1: Reset o2 Blm Cells
- F6: Miscellaneous Tests; f1: Reset Iac Blm Cells
- F6: Miscellaneous Tests; f1: Reset Knock Cells
- Multec-S (C16XE) - Introduction
- F6: Miscellaneous Tests; F0: Reset Idle Adjust (Mt or at Vehicles)
- Multec-S (C16XE) - Survey of Systems Table
- F7: Programming Immobiliser
- Multec-S (C16XE) - Diagnosis
- F8: ECU Control RPM Control
- Multec-S (C16XE) - Vehicle Systems, Model Year '94
- F8: ECU Control Inj. Control
- Multec-S (C16XE) - General Safety Measures and Repair Instructions
- Immob. Func. for Engine - Introduction
- Multec-S (C16XE) - Survey of Vehicles
- Immob. Func. for Engine - Diagnosis
- Multec-S (C16XE)-Survey of Cont. Units
- Immob. Func. for Engine - Read Trouble Code
- F2:Trouble Code Table Trouble Code 13 02 Sensor Open Circuit
- Immob. Func. for Engine - Check Data List Parameters
- F2:Trouble Code Table Trouble Code 14 Coolant Temperature Voltage Low
- Immob. Func. for Engine - Carry Out Actuator Tests
- F2:Trouble Code Table Trouble Code 15 Coolant Temperature Voltage High
- Immob. Func. for Engine - Carry Out Control Tests
- F2:Trouble Code Table Trouble Code 16 Knock Signal Circuit
- Immob. Func. for Engine - Snapshot Mode
- F2:Trouble Code Table Trouble Code 18 Knock Control System
- Immob. Func. for Engine - Final System Test
- F2:Trouble Code Table Trouble Code 19 Incorrect RPM Signal
- Immob. Func. for Engine - General Safety Measures and Repair Instructions
- F2:Trouble Code Table Trouble Code 21 Throttle Posit. Sensor Voltage High
- F2:Trouble Code Table Trouble Code 22 Throttle Posit. Sensor Voltage Low
- F2:Trouble Code Table Trouble Code 24 No Vehicle Speed Signal
- F2:Trouble Code Table Trouble Code 25 Injector Valve Voltage Low
- F2:Trouble Code Table Trouble Code 28 Fuel Pump Relay Contact Problem
- F2:Trouble Code Table Trouble Code 29 Fuel Pump Relay Voltage Low
- F2:Trouble Code Table Trouble Code 32 Fuel Pump Relay Voltage High
- F2:Trouble Code Table Trouble Code 35 Idle Air Control
- F2:Trouble Code Table Trouble Code 44 Lean Exhaust
- F2:Trouble Code Table Trouble Code 45 Rich Exhaust
- Survey of Vehicle (Multec)
- F2:Trouble Code Table Trouble Code 46 Est Lines Voltage High
- Multec - F2:Trouble Codes - TC 83 Immobiliser No or Wrong Coding
- F2:Trouble Code Table Trouble Code 49 Battery Voltage High
- Multec - F2:Trouble Codes - TC 84 Immobiliser No Signal
- F2:Trouble Code Table Trouble Code 51 Replace ECU or Prom
- Multec - F2:Trouble Codes - TC 85 Immobiliser Wrong Signal
- F2:Trouble Code Table Trouble Code 55 Replace ECU
- Multec - F0: Data List - Test Step 01 Immobiliser Sig.
- F2:Trouble Code Table Trouble Code 63 Est Line Coil Cyl 2+3 Voltage Low
- Multec - F0: Data List - Test Step 02 Immobiliser
- F2:Trouble Code Table Trouble Code 64 Est Line Coil Cyl 1+4 Voltage Low
- Multec - F5:Actuator Test - Number 1 Immo. Sig. Test
- F2:Trouble Code Table Trouble Code 67 Mass Air Flow Sensor Range
- Multec - F7: Programming Immobiliser
- F2:Trouble Code Table Trouble Code 68 Mass Air Flow Sensor Frequency
- F2:Trouble Code Table Trouble Code 72 Est Lines Open Circuit
- F2:Trouble Code Table Trouble Code 81 Injector Valve Voltage High
- Astra X16SZR Juddering at 1,500 RPM Cor/tig X14XE at Warm-Up Backfiring
- F2:Trouble Code Table Trouble Code 92 Hall Sensor Circuit
- F2:Trouble Code Table Trouble Code 93 Quad Driver Module (Qdm)
- Quick Check F0:Data List No.01 Battery Voltage
- Quick Check F0:Data List No.02 Coolant Temperature
- Quick Check F0:Data List No.03 Mass Air Flow S.
- Quick Check F0:Data List No.04 Engine Load
- Quick Check F0:Data List No.05 TPS Signal
- Quick Check F0:Data List No.06 Engine Speed
- Quick Check F0:Data List No.07 Iac Cntr. Enable
- Quick Check F0:Data List No.08 Idle Air Control
- Quick Check F0:Data List No.09 02 Sensor Loop
- Quick Check F0:Data List No.10 02 Sensor
- Quick Check F0:Data List No.11 02 Integrator
- Quick Check F0:Data List No.12 02 Blm Enable
- Quick Check F0:Data List No.13 02 Blm Cell No.
- Quick Check F0:Data List No.14 02 Blm Cell Cont
- Quick Check F0:Data List No.15 02 Toggle Rate
- Quick Check F0:Data List No.16 02 Blm Part Ref.
- Quick Check F0:Data List No.17 Air/fuel Ratio
- Quick Check F0:Data List No.18 Power Enrichment
- Quick Check F0:Data List No.19 Clear Flood Mode
- Quick Check F0:Data List No.20 Dec. Fuel Cutoff
- Quick Check F0:Data List No.21 Fuel Tank Vent.
- Quick Check F0:Data List No.22 Fuel Tank Valve
- Quick Check F0:Data List No.23 A/c Informat. Sw
- Quick Check F0:Data List No.24 A/c Load Signal
- Quick Check F0:Data List No.25 A/c Relay
- Quick Check F0:Data List No.26 Fuel Pump Relay
- Quick Check F0:Data List No.27 Vehicle Speed
- Quick Check F0:Data List No.28 Vehicle Sp.pulse
- Quick Check F0:Data List No.29 Knock Control
- Quick Check F0:Data List No.30 Knock Voltage
- Quick Check F0:Data List No.31 Knock Cell No.
- Quick Check F0:Data List No.32 Knock Rtd. cyl.1
- Quick Check F0:Data List No.33 Knock Rtd. cyl.2
- Quick Check F0:Data List No.34 Knock Rtd. cyl.3
- Quick Check F0:Data List No.35 Knock Rtd. cyl.4
- Quick Check F0:Data List No.36 Injection Pulse
- Quick Check F0:Data List No.37 Spark Advance
- Quick Check F0:Data List No.38 Diag. Request
- Quick Check F0:Data List No.39 Idle Adjust
- Quick Check F0:Data List No.40 Des. Idle Adjust
- Quick Check F0:Data List No.41 Idle Adjust
- Quick Check F0:Data List No.42 Injector Cutoff
- Multec-M (14SE/C14SE/C16SE)-Introduction
- Multec-M (14SE/C14SE/C16SE) - Survey of Systems Table
- Multec-M (14SE/C14SE/C16SE) - Diagnosis
- Multec-M (14SE/C14SE/C16SE) - Vehicle Systems, Model Year '94
- Multec-M (14SE/C14SE/C16SE) - General Safety Measures and Repair Instructions
- Multec-M (14SE/C14SE/C16SE) - Survey of Vehicles
- Multec-M (14SE/C14SE/C16SE) - Survey of Control Units, Table 3
- F2:Trouble Code Table Trouble Code 33 MAP Sensor Voltage High
- F2:Trouble Code Table Trouble Code 34 MAP Sensor Voltage Low
- F2:Trouble Code Table Trouble Code 41 Est Line Coil Cyl 2+3 Voltage High
- F2:Trouble Code Table Trouble Code 42 Est Line Coil Cyl 1+4 Voltage High
- F2:Trouble Code Table Trouble Code 69 Intake Air Temperature Voltage Low
- F2:Trouble Code Table Trouble Code 71 Intake Air Temperature Voltage High
- F2:Trouble Code Table Trouble Code 75 Torque Control Voltage Low
- F2:Trouble Code Table Trouble Code 76 Continuous Torque Control
- Engine Run - Engine Stalls When Coasting
- Quick Check F0:Data List No.02 Ron Coding
- Quick Check F0:Data List No.03 Coolant Temperature
- Quick Check F0:Data List No.04 Intake Air Temperature
- Quick Check F0:Data List No.05 MAP Sensor
- Quick Check F0:Data List No.06 TPS Signal
- Quick Check F0:Data List No.07 Diag. Request
- Quick Check F0:Data List No.08 Fuel Pump Relay
- Quick Check F0:Data List No.09 Park/neutral Sw.
- Quick Check F0:Data List No.10 Torque Control
- Quick Check F0:Data List No.11 Vehicle Sp. Pulse
- Quick Check F0:Data List No.12 Vehicle Speed
- Quick Check F0:Data List No.13 Desired Idle
- Quick Check F0:Data List No.14 Engine Speed
- Quick Check F0:Data List No.15 Idle Air Control
- Quick Check F0:Data List No.16 Spark Advance
- Quick Check F0:Data List No.17 02 Sensor Loop
- Quick Check F0:Data List No.18 02 Sensor
- Quick Check F0:Data List No.19 02 Integrator
- Quick Check F0:Data List No.20 02 Blm Enable
- Quick Check F0:Data List No.21 02 Blm Cell No.
- Quick Check F0:Data List No.22 02 Blm Cell Cont
- Quick Check F0:Data List No.23 Air/fuel Ratio
- Quick Check F0:Data List No.24 Injection Pulse
- Quick Check F0:Data List No.25 Clear Flood Mode
- Quick Check F0:Data List No.26 Dec. Fuel Cutoff
- Quick Check F0:Data List No.27 Power Enrichment
- Quick Check F0:Data List No.28 Iac Cntr. Enable
- Quick Check F0:Data List No.29 A/c Informat. Sw
- Quick Check F0:Data List No.30 A/c Load Signal
- Quick Check F0:Data List No.31 A/c Relay
- Quick Check F0:Data List No.32 A/c Cutoff
- Quick Check F0:Data List No.33 CO Fuel Correc.
- Multec (X12SZ/X16SZ) - Introduction
- Multec (X12SZ/X16SZ) - Survey of Systems Table
- Multec (X12SZ/X16SZ) - Diagnosis
- Multec (X12SZ/X16SZ) - Vehicle Systems, Model Year '94
- Multec (X12SZ/X16SZ) - General Safety Measures and Repair Instructions
- Multec (X12SZ/X16SZ) - Survey of Vehicles
- Multec (X12SZ/X16SZ) - Survey of Control Units, Table 3
- F2:Trouble Code Table Trouble Code 43 Linear EGR System
- F2:Trouble Code Table Trouble Code 47 Linear EGR Position
- Quick Check F0:Data List No.03 MAP Sensor
- Quick Check F0:Data List No.04 TPS Signal
- Quick Check F0:Data List No.05 Engine Speed
- Quick Check F0:Data List No.06 Desired Idle
- Quick Check F0:Data List No.16 EGR Position Cmd
- Quick Check F0:Data List No.17 EGR Pos. Fdbk
- Quick Check F0:Data List No.18 Air/fuel Ratio
- Quick Check F0:Data List No.19 Power Enrichment
- Quick Check F0:Data List No.20 Clear Flood Mode
- Quick Check F0:Data List No.21 Dec. Fuel Cutoff
- Quick Check F0:Data List No.22 Fuel Tank Vent.
- Quick Check F0:Data List No.23 Vehicle Speed
- Quick Check F0:Data List No.24 Vehicle Sp. Pulse
- Quick Check F0:Data List No.25 Knock Pulses
- Quick Check F0:Data List No.26 Knock Voltage
- Quick Check F0:Data List No.27 Knock Rtd. Cyl 1,4
- Quick Check F0:Data List No.28 Knock Rtd. Cyl 4,1
- Quick Check F0:Data List No.29 Knock Rtd. Cyl 2,3
- Quick Check F0:Data List No.30 Knock Rtd. Cyl 3,2
- Quick Check F0:Data List No.31 Park/neutral Sw.
- Quick Check F0:Data List No.32 Torque Control
- Quick Check F0:Data List No.33 Injection Pulse
- Quick Check F0:Data List No.34 Spark Advance
- Quick Check F0:Data List No.35 Fuel Pump Relay
- Quick Check F0:Data List No.36 Diag. Request
- Quick Check F0:Data List No.37 Spark Table 91
- Quick Check F0:Data List No.38 Spark Table 95
- Quick Check F0:Data List No.39 Des. Idle Adjust
- Quick Check F0:Data List No.40 Idle Adjust
- Quick Check F0:Data List No.41 Desired Idle P-N
- Quick Check F0:Data List No.42 Idle Adjust P-N
- Quick Check F0:Data List No.43 Des. Idle Drive
- Quick Check F0:Data List No.44 Idle Adjust Drive
- Multec (12NZ/C12NZ/C14NZ) - Introduction
- Multec (12NZ/C12NZ/C14NZ) - Survey of Systems Table
- Multec (12NZ/C12NZ/C14NZ) - Diagnosis
- Multec (12NZ/C12NZ/C14NZ) - Vehicle Systems, Model Year '94
- Multec (12NZ/C12NZ/C14NZ) - General Safety Measures and Repair Instuctions
- Multec (12NZ/C12NZ/C14NZ) - Survey of Vehicles
- Multec (12NZ/C12NZ/C14NZ) - Survey of Control Units Table 3
- Quick Check F0:Data List No.06 Idle Air Control
- Throttle Valve Adjuster Voltage High
- Quick Check F0:Data List No.07 02 Sensor Loop
- Quick Check F0:Data List No.08 02 Sensor
- Quick Check F0:Data List No.09 02 Integrator
- Quick Check F0:Data List No.10 02 Blm Idle Thr.
- Quick Check F0:Data List No.11 02 Blm Part Thr.
- Quick Check F0:Data List No.13 Air/fuel Ratio
- Quick Check F0:Data List No.14 Vehicle Speed
- Quick Check F0:Data List No.15 Vehicle Sp.pulse
- Quick Check F0:Data List No.16 Ron Coding
- Quick Check F0:Data List No.17 Spark Advance
- Quick Check F0:Data List No.18 Dec. Fuel Cutoff
- Quick Check F0:Data List No.21 Injection Pulse
- Quick Check F0:Data List No.22 Park/neutral Sw.
- Quick Check F0:Data List No.23 Diag. Request
- Quick Check F0:Data List No.24 Controlled RPM
- Quick Check F0:Data List No.25 CO Fuel Correc.
- Quick Check F0:Data List No.26 A/c Informat. Sw
- Quick Check F0:Data List No.27 Torque Control
- How to Check (Multec) the Fuel Pressure
- How to Replace the Fuel Port Gasket
- How to Remove and Install Reinstallation the Fuel Pump Relay
- How to Remove and Install the Pressure Sensor - Intake Pipe
- How to Remove and Install the Coolant Temperature Sensor
- How to Check the Coolant Temperature Sensor
- Octane Number Plug, Code(12 Nz, C 12 NZ, C 14 NZ)
- How to Remove and Install (X 12 SZ the Knock Sensor (X 14 SZ))
- How to Remove and Install (X 12 SZ the Knock Module (X 14 SZ))
- How to Remove and Install (X 12 SZ the Inductive Pulse Pick-Up (X 14 SZ))
- How to Remove and Install (X 12 SZ the Exhaust Gas Recirculation Valve (X 14 SZ))
- How to Remove and Install (X 12 SZ the Exhaust Gas Recirculation Module (X 14 SZ) Sz))
- Ignition Basic Adjustment, Perform (12NZ, C12NZ, C14NZ)
- How to Remove and Install 12NZ the Ignition Distributor (C12NZ, C14NZ)
- How to Remove and Install 12NZ the Ignition Coil (C12NZ, C14NZ)
- How to Check 12NZ the Ignition Coil (C12NZ, C14NZ C14NZ)
- How to Remove and Install 12NZ the Ignition Module (C12NZ, C14NZ)
- How to Remove and Install the Control Unit
- How to Remove and Install the Throttle Body
- How to Remove and Install the Throttle Valve Potentiometer
- How to Remove and Install the Idle Speed Stepper Motor
- How to Check (Multec-M) the Fuel Pressure
- How to Remove and Install the Fuel Pressure Regulator
- How to Remove and Install Reinstallation the Injectors
- How to Remove and Install the Intake Air Temperature Sensor
- How to Measure the Reference Gap Between Inductive Pulse Pick-Up and Increment Disc
- How to Remove and Install the Inductive Pulse Pick-Up
- How to Code the Octane Number Plug
- How to Remove and Install the Oxygen Sensor
- How to Remove and Install Reinstallation the Dis Ignition Module
- How to Remove and Install the Immobiliser with Transponder as of MY '96 Immobiliser Control Unit
- X/Z10XE, X/Z12 XE-Engines (Oil Non-Return-Valve in Cylinderblock Removed)
- Illustration: Multec-S (C16XE)
- How to Remove and Install (C16XE) the Hot Wire Mass Air Flow Meter
- How to Remove and Install (X 14 XE the Pressure Sensor - Intake Pipe (C 14 SEL, X 16 XE, C 16 SEL))
- How to Remove and Install (X14XE the Intake Air Temperature Sensor (C14SEL, X16XE, C16SEL))
- How to Remove and Install the Knock Sensor
- How to Replace (Up to MY '96 1/2)". 1996 1/2) the Program Memory in Control Unit, Knock Module in Control Unit or Control Unit
- Illustration: Mechanical Injection System
- Illustration: Injector Nozzle
- How to Remove and Install the Distributor Injection Pump
- How to Remove and Install Reinstallation the Injection Nozzles
- How to Check the Injector Nozzle
- How to Clean the Injector Nozzle
- How to Remove and Install the Solenoid Cutoff Valve Control Unit (As of MY '96 1996))
- How to Replace the Fuel Filter Element
- How to Remove and Install Reinstallation the Fuel Filter Heating
- Technical Data - Identification/data (Mechanical Injection System) (15D)
- Technical Data - Identification/data (Mechanical Injection System) (15 Dt, X 15 DT)
- Technical Data - Identification/data (Mechanical Injection System) (17D, X17D )
- Illustration: Multec 12 Nz, C 12 NZ, C 14 NZ
- Important Workshop Instructions
- How to Remove and Install the Throttle Valve Injection Housing
- How to Remove and Install the Throttle Valve Injection Housing, Upper Part
- How to Replace the Fuel Pressure Regulator Diaphragm
- How to Remove and Install the Vacuum Connection Flange
- How to Remove and Install Reinstallation the Injection Valve
- How to Measure (X 12 SZ the Reference Gap Between Inductive Pulse Pick-Up and Increment Disc (X 14 SZ))
- How to Remove and Install (All Except 12 Nz) the Oxygen Sensor
- How to Remove and Install (X 12 SZ the Controlled Canister Purge Valve (X 14 SZ))
- How to Remove and Install X 12 SZ the Dis Ignition Module (X 14 SZ)
- How to Replace (X12SZ) Replacement (X12SZ) the Control Unit Program Memory or Control Unit
- Illustration: Multec-M (C14SE)
- How to Replace the Control Unit Program Memory or Control Unit
- How to Remove and Install (X15DT the Control Unit - Solenoid Cutoff Valve (X17D))
- How to Remove and Install the Solenoid Cutoff Valve
- How to Remove and Install (X15DT the Solenoid Cutoff Valve (X17D))
- How to Remove and Install (X17D) the Accelerator Linkage Damper
- How to Remove and Install Reinstallation the Tank Vent Valve
- Fuel Fine Filter (Microfilter)
- Engine Compartment Survey (Continued) (Continued)
- How to Remove and Install Reinstallation the Tank Vent System
- How to Remove and Install the Oxygen Sensor (X 12 XE)
- How to Remove and Install (Rhd) the Engine Control Unit
- Engine Management System Motronic M1.5. 5, Engine Compartment Survey
- How to Remove and Install the Throttle Valve Adjuster
- How to Remove and Install the Oxygen Sensor (X 10 XE)
- How to Remove and Install Reinstallation the Ignition Module
- How to Remove and Install the Hot Film Mass Air Flow Meter
- How to Remove and Install (Lhd) the Engine Control Unit
- Engine Management
- ABS
- ABS 4/4-F
- ABS 5.3
- Additional Lighting
- Adhesive Foiles
- Air Conditioning
- Airbag
- Antenna
- Anti-Theft Warning System-M
- Anti-Theft Warning System-S
- Automatic Transmission Front Wheel Drive
- Battery
- Body Equipment
- Brake Hydraulics, Brake Lines
- Brakes
- Central Door Locking System
- Clutch
- Clutch and Transmission
- Communication / Navigation
- Connector pinouts
- Cooling System
- Corrosion Protection
- Diesel Engine
- DOHC Petrol Engine
- Electrical Equipment and Instruments
- Electrical Window Winders
- Engine and Engine Aggregates
- Engine Electrics
- Eps Electrical Power Steering
- Exhaust System
- Fittings, Hinges, Locks
- Folding Roof
- Frame
- Front Wheel Brake
- Front Wheel Suspension
- Front Wheel Suspension, Wheels and Tyres
- Fuel and Exhaust System
- Fuel Injection Systems
- Fuel System
- Fuse Box
- General Vehicle Information
- Glass, Window Guides, Window Winders
- Headlamps, Lamps and Horn
- Heating, Ventilation
- Heating, Ventilation, Air Conditioning (HVAC)
- Immobiliser
- Info Display Ccrt 700
- Instruments, Telltales
- Maintenance, Body and Chassis Sheet Metal Parts, Frame
- Manual Transmission Front Wheel Drive
- OHC Petrol Engine
- Other Accessories
- Outside Rear View Mirror
- Paint
- Painting Repair Operations
- Painting Repair System
- Power Steering
- Radiator Grille
- Radio
- Radio Interference Suppression
- Rear Axle and Rear Wheel Suspension
- Rear Axle Front Wheel Drive
- Rear End
- Rear Wheel Brake
- Roof
- Roof Box
- Roof Luggage Carrier (Railing)
- Seat Heating Systems
- Seats, Upholstery, Inner Trim Panels
- Secondary Air Injection
- Service Brake, Parking Brake
- Sheet Metal Parts (Bolted)
- Sheet Metal Parts (Cement and Seal)
- Sheet Metal Parts (Welded)
- Sliding Roof
- Special Installations
- Steering
- Steering Gear
- Steering Linkage
- Steering Wheel - Steering Column
- Switches, Control Unit, Relays, Ignition Lock
- TID (Triple Info Display)
- Trailer Hitch
- Trim Panels, Radiator Grille, Spoiler
- Trim Strips, Lettering, Coverings
- Turbo-Charging
- Vehicle Side
- Wheels and Tyres
- Windscreen Wash/wipe System, Heated Screen
- Wiring Harnesses