Home ReviewsRefund
Home/Opel/Vectra/Opel Vectra C (2002-2008)/Repair manual/DOHC Petrol Engine/Special Service Tools
Contents Wiring diagrams Section: DOHC Petrol Engine All sections

Special Service Tools Opel Vectra C

DOHC Petrol Engine 47 illustrations
KM-161-BRemover
To press out tie rod end from steering knuckle
KM-313Slide Hammer
To remove axle shafts in conjunction with KM-902
KM-412-AEngine Overhaul Stand
To hold removed engine
KM-412-31Engine adapter
Engine mounting in conjunction with KM-412-A
KM-422Installer
Press in sealing ring, camshaft
KM-427Remover and installer
Tap centring pins into cylinder block
KM-468-BHolding Wrench
Counterhold wheel hub when fitting the axle nuts
KM-470-BAngular Torque Wrench
To tighten cylinder head bolts
KM-471Adapter
Check cooling system under pressure in conjunction with cooling system tester
KM-498-BOil Pressure Gauge
Check engine oil pressure in conjunction with KM-135
KM-527-AAdjustment pin
Lock, selector lever
MKM-558-10Closure cover
Sealing the brake fluid reservoir when opening the brake system
MKM-571-BDial gauge
Check various components
MKM-596-ATemperature Gauge
To measure oil temperature
MKM-604-DTorx Bit and Socket Set
To remove/install Torx bolts
KM-609Electronic kit I
Diagnosis of electronic and electrical systems
MKM-610Torque wrench 1/2"
Range 30–130 Nm.
MKM-611Torque Wrench, 3/8"
Range 10–60 Nm.
KM-652Flywheel Holder
To lock flywheel or drive disc
MKM-667Pressure and Vacuum Pump
Check vacuum unit for leak
MKM-669Torque wrench 1/2"
Range 50–300 Nm.
KM-796-ADismantler
To open quick-release fittings for fuel system
KM-840Remover
Remove valve stem seal
KM-845Suction device
To remove the hydraulic valve lifters
KM-902Remover
To remove axle shafts in conjunction with KM-313
KM-904Base Frame
To remove and install various vehicle components with additional adapters
KM-956-1Handle
Holding the camshaft sprockets to release/tighten the fastening bolts in conjunction with KM-6347
KM-958Installer
For installing valve stem seal
KM-2358Wire Cable
To suspend engine
KM-6001-AEngine mounting
For centring the engine in conjunction with KM-6173
KM-6009Remover/Installer
Removal and installation of ignition module
MKM-6086Valve spring lever automatic system
Removal and installation of valve spring and shim
KM-6173Engine mounting
Bracket, engine to front axle body, in conjunction with KM-6313
KM-6179Remover/Installer
Removal and installation of oxygen sensor in manifold with MKM-611
KM-6333Locating pin
Fixing the toothed belt tensioning device
KM-6340Locking Tool
Fixing the camshaft gears to check and adjust timing
KM-6349Locating pin
For fixing the ribbed V-belt tension roller
KM-6351Assembly Sleeves
Installation of crankshaft sealing ring front (DOHC-I engine, 3rd gen.)
KM-6361Gap feeler gauges
Measuring valve play (DOHC-I engine, 3rd gen.)
KM-6363Spark Plug Key
Removal and installation of spark plugs (DOHC-I engine, 3rd gen.)
KM-6390Centring Tool
Remove and install front axle and align subframe with vehicle underbody in conjunction with KM-904 and hydraulic jack
KM-6623Installer
To install crankshaft seal ring (transmission side)
KM-6624Remover
To remove crankshaft seal ring (transmission side)
KM-6625Flywheel Holder
Immobilize the flywheel with transmission installed
KM-6628-AFixing tool
Fixing the camshafts in TDC position to check and adjust timing
KM-J-34730-91Pressure Tester
To check fuel pressure
KM-J-45000Remover
To remove various seal rings

More articles — Engine and Engine Aggregates