The engine compartment electronics module (Underhood Electrical Centre, UEC)
| 1 | Engine compartment electronic module |
The illustration shows the engine compartment electronics module with the cover removed.
Home/Opel/Vectra/Opel Vectra C (2002-2008)/Repair manual/DOHC Petrol Engine/Engine Compartment Electronics Module (UEC) - Survey
Contents
Wiring diagrams Section: DOHC Petrol Engine- How to Check and Measure the Cylinder Head and Attaching Parts (Survey)
- How to Check the Cylinder Head Height
- Air Mass Meter, 6 Cylinder Petrol (Motronic)
- How to Check for Plane Surface the Cylinder Head
- Air Mass Meter, 4 Cylinder Petrol
- How to Measure the Valve
- How to Check the Inner Diameter of Valve Guide
- Valve Stem Play, Determine
- Air Mass Meter, Z18XE, Z20LEL, Y22XE, Z22XE
- How to Check the Installation Height of Valves
- How to Check the Installation Height of Valve Guide
- Battery / Starter, Petrol (Current Measurement)
- Battery / Starter (Voltage Measurement)
- How to Overhaul the Cylinder Head
- Revised Camshafts - Z 20 NET Petrol Engine
- Cylinder Head, Attach to Assembly Tool Set KM-6215
- Cylinder Head, Disassemble
- Elimination of Exhaust Gas Recirculation Valve - Z 22 YH Petrol Engine
- How to Remove the Valves
- Flexible Maintenance Intervals - Vectra-C / Signum
- Compression 4-cylinder, Unsynchronised
- Valve Seat, Cut (In Cylinder Head)
- Compression 6-cylinder, Unsynchronised
- Engine Control Unit ECM Z 16 XE - Function
- Valve Guide, Ream
- Engine Control Unit ECM Z 18 XE - Function
- Crankshaft Impulse Sensor, Petrol and Z19DT
- Valve, Grind
- Engine Control Unit ECM Z 22 SE - Function
- Survey Vectra-C / Signum
- Valve, Grind In
- Engine Control Unit ECM Z 32 SE - Function
- New Engine Oil Cooler on Z 20 NET Petrol Engine
- How to Replace the Valve Stem Seals
- How to Assemble the Cylinder Head
- Cylinder Head Machining Special Tools
- Survey of All Vehicle Types
- Measuring Oil Consumption
- Modification Package for Z 20 NET DOHC Petrol Engine
- Injector (Multi-Point Fuel Injection), All Except Z22YH
- Intake Manifold Absolute Pressure (MAP) Sensor
- Engine Identifier
- Knock Sensor
- Lubrication of Radial Shaft Seal Rings No Longer Applicable
- Vacuum Pump - Z 28 NET / Nel V6 Petrol Engines
- Petrol Turbo Engine Z 20 ET - Overview
- View of Engine
- Turbo-Charging System
- Exhaust Manifold
- Crank Mechanism
- Fuel Distributor Pipe
- Cooling System
- Engine Oil Circulation
- Introduction - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Engine Management
- Views of Engines - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Inlet Manifold
- Engine-Specific Data - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Torque and Power Curves - Z 28 NEL V6 Petrol Engine
- Vacuum Pump
- Torque and Power Curves - Z 28 NET V6 Petrol Engine
- Cylinder Head
- Location of Engine Number - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Balancing Shafts
- Removing the Engine - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Camshaft Sensor, F9Q, Y26SE, Y32SE, Z32SE, ZD3
- Crank Case Ventilation
- Tank Ventilation System
- Ribbed V-Belt - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Camshaft Sensor, Multec S/f Except Z14XE MY2004
- Camshaft Sensor, Simtec 70/71/81
- Omission of Agr from Z 22 SE DOHC Gasoline Engines
- Exhaust Manifold Z 28 NEL / Z 28 NET V6 Petrol Engine
- Modified Camshaft Bearing Cover Bolted Connection
- Intake Manifold - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Engine Cooling Module - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Valve Timing - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Ignition, Primary, Z14XE, Z16XE, Z16YNG
- Dohc-Petrol Engine Z 22 SE
- Timing Chains - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Cylinder Block - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Damage Diagnosis, Dual Mass Flywheel
- Crankshaft Seal Ring - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Pistons and Connecting Rods - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Crank Drive - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Throttle Valve Potentiometer (Double Signal), Multec/trionic (MY 2001,MY 2002 and MY 2003), Simtec (MY 2001 and MY 2002)
- Cylinder Heads - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Throttle Valve Potentiometer (Double Signal), Motronic (As of MY2001)
- Secondary Air Injection - Z 28 NEL / Z 28 NET V6 Petrol Engine
- Pedal Position Double Signal, All Petrol (MY 2002, MY 2003 and MY 2004)
- Exhaust Gas Recirculation Valve, All Petrol (MY 2002, MY 2003 and MY2004)
- Exhaust Gas Recirculation Valve, Motronic1.5.5 and Motronic 3.11 (MY2002 and MY 2003)
- Purging Air Line No Longer Fitted on Z 20 NET DOHC Turbo Petrol Engine
- All OHC and Dohc-Ii Petrol Engines
- Modifications to the Z 22 YH DOHC Petrol Engine - Vectra-C, Signum
- Ignition to Crankshaft Signal
- Exhaust Gas Recirculation Valve, Z22SE (MY 2002, MY 2003 and MY 2004)
- Introduction
- Throttle Valve Potentiometer (Double Signal), Simtec (MY 2003), Simtecand Multec-F (MY 2004)
- Air Mass Meter, Z20NET, Z17DTL, Z17DTH, Z19DT, Z19DTH
- Injector (Multi-Point Fuel Injection), Z22YH
- Wheel Speed Sensor (Hall Type), Vectra-C/signum
- Engines - Survey
- Pedal Position Double Signal, Vectra-C Z22SE (MY 2003)
- Engine Identification
- Survey of Engine Characteristic Data and Engine Management Systems
- Load Pressure Sensor, Signum Z20NET
- Engine / Transmission Mountings
- Z 16 XE Dohc-I Petrol Engine - Survey
- View of Engine, Z 16 XE
- Torque and Output Curve, Z 16 XE
- Z 18 XE Dohc-I Petrol Engine - Survey
- View of Engine, Z 18 XE
- Torque and Output Curve, Z 18 XE
- Z 22 SE DOHC Petrol Engine - Survey
- Torque and Output Curve, Z 22 SE
- Z 32 SE V6 DOHC Petrol Engine - Survey
- View of Engine, Z 32 SE
- Torque and Output Curve, Z 32 SE
- Toothed Belt, Z 32 SE
- Intake Plenum, Z 32 SE
- Engine / Transmission Combinations
- Dohc-I Petrol Engine Z 18 XE - Overview
- View of Engine Z 18 XE
- Torque and Power Curves of the Z 18 XE
- Z 20 NET DOHC Petrol Engine - Overview
- View of Z 20 NET Engine
- Z 22 YH DOHC Petrol Engine
- Torque and Power Curves of the Z 20 NET Engine
- Z 20 NET DOHC Turbo Petrol Engine
- Z 32 SE V6 DOHC Petrol Engine - Overview
- View of Engine Z 32 SE
- Torque and Power Curves of the Z 32 SE
- Exhaust Gas Recirculation Valve, Z22YH
- Z 22 YH DOHC Petrol Engine - Overview
- View of Engine Z 22 YH
- Torque and Power Curves of the Z 22 YH
- DOHC Petrol Engine Z 22 YH - System Description - Engine Management
- High-Pressure Fuel Pump of the Z 22 YH
- Inlet Manifold of the Z 22 YH
- Allocation - Engine / Vehicle Equipment and Battery
- Fuel Rail of the Z 22 YH
- Allocation - Engine / Vehicle Equipment and Alternator
- Ignition Module for the Z 22 YH
- Engine Compartment Electronics Module (UEC) - Survey
- Exhaust Gas Recirculation Valve for the Z 22 YH
- UEC - Arrangement of Relays and Fuses
- Pistons of the Z 22 YH
- Connecting-Rod of the Z 22 YH
- Injection Valve Control System on the Z 22 YH
- Crankcase Ventilation System of the Z 22 YH
- The Z 22 YH Engine - General
- Block Circuit Diagram of Z 22 YH
- View of Engine, Z 22 SE
- Engine Number
- How to Check (Z 16 XE the Compression (AC, Lhd))
- How to Check (Z 16 XE) the Oil Temperature
- How to Check (Z 16 XE the Engine Oil Pressure (With AC, Lhd))
- How to Check (Z 16 XE the Timing (Air Conditioning, Lhd))
- How to Check and Adjust (Z 16 XE the Timing (With AC, Lhd))
- How to Check and Correct (Z 16 XE the Toothed Belt Tension (AC, Lhd))
- How to Check (Z 16 XE the Toothed Belt Tension (With AC, Lhd))
- Illustration: Z 16 XE
- How to Remove and Install (Z 16 XE the Toothed Belt Cover - Upper Part (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Toothed Belt Cover - Lower Part (With AC, Lhd))
- How to Replace (Z 16 XE the Toothed Belt (With AC, Lhd))
- How to Replace (Z 16 XE the Toothed Belt Guide Pulley (With AC, Lhd))
- How to Replace (Z 16 XE the Another Toothed Belt Guide Pulley (With AC, Lhd))
- How to Replace (Z 16 XE the Toothed Belt Cover - Rear (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Ribbed V-Belt Tensioner (With AC, Lhd))
- How to Replace (Z 16 XE the Toothed Belt Tension Roller (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Cylinder Head Cover (Air Conditioning, Lhd))
- How to Remove and Install (Z 16 XE the Both Camshafts (With AC, Lhd))
- How to Replace (Z 16 XE the Seal Rings - Front Camshaft (With AC, Lhd))
- How to Replace (Z 16 XE the Camshaft Sprocket (With AC, Lhd))
- How to Replace (Z 16 XE the Gasket - Exhaust Manifold (With AC, Lhd))
- How to Replace (Z 16 XE the Gasket - Intake Manifold Upper Part (With AC, Lhd))
- How to Replace (Z 16 XE the Gasket - Intake Manifold Lower Part (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Cylinder Head (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Flywheel (With AC, Lhd))
- How to Replace (Z 16 XE the Seal Ring - Crankshaft, Rear (With AC, Lhd))
- How to Replace the Flange - Cylinder Block Ventilation/engine Vent Housing
- Engine Oil Change (Z 16 XE, with AC, Lhd)
- How to Replace (Z 16 XE the Oil Filter Short Circuit Valve (With AC, Lhd))
- How to Replace (Z 16 XE the Seal Ring - Crankshaft, Front (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Oil Pan (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Oil Pump (With AC, Lhd))
- How to Check the Oil Pump
- How to Remove and Install (Z 16 XE the Oil Pump Pressure Regulating Valve (With AC, Lhd))
- How to Replace (Z 16 XE the Intake Pipe for Oil Pump (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Oil Baffle Plate (With AC, Lhd))
- How to Replace (Z 16 XE the Oil Dipstick Guide Tube (With AC, Lhd))
- Sensor - Dynamic Oil Level Check (Z 16 XE, with AC, Lhd)
- How to Check for Leaks the Engine ((CO Content in Cooling System) (Z 16 XE))
- How to Replace (Z 16 XE the Engine Damping Blocks (Both Sides) (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Reaction Member - Front (With AC, Lhd))
- How to Replace (Z 16 XE the Reaction Member - Rear (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Engine Damping Block - Right (With AC, Lhd))
- How to Replace (Z 16 XE the Engine Damping Block - Left (With AC, Lhd))
- How to Remove and Install (Z 16 XE the Engine with Transmission (With AC, Lhd))
- How to Remove and Install from Engine (Z 16 XE the Manual Transmission (With AC, Lhd))
- Engine Compartment Survey (Z 16 XE)
- Special Service Tools
- Sealants, Lubricants and Locking Agents
- Specifications
- Recommended Torque Values
- DOHC I Petrol Engine (Z 18 XE, Z 18 XEL)
- How to Check (Z 18 XE the Oil Temperature (Z 18 XEL))
- How to Check (Z 18 XE the Engine Oil Pressure (Z 18 XEL, with AC, Lhd))
- How to Check (Z 18 XE the Timing (Z 18 XEL, with AC, Lhd))
- How to Check and Adjust (Z 18 XE the Timing (Z 18 XEL, with AC, Lhd))
- How to Check and Correct (Z 18 XE the Toothed Belt Tension (Z 18 XEL, with AC, Lhd))
- How to Check (Z 18 XE the Toothed Belt Tension (Z 18 XEL, with AC, Lhd))
- Illustration Z 18 XE, Z 18 XEL
- How to Replace (Z 18 XE the Ribbed V-Belt (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Ribbed V-Belt Tensioner (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Toothed Belt Cover - Upper Part (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Toothed Belt Cover - Lower Part (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Toothed Belt (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Toothed Belt - Tension Roller (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Toothed Belt Guide Roller (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Toothed Belt Cover - Rear (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Cylinder Head Cover (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Seal Rings - Camshaft, Front (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Both Camshafts (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Gasket - Exhaust Manifold (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Gasket - Intake Manifold (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Cylinder Head (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Flywheel (Z 18 XEL, with AC, Lhd))
- How to Replace (With A/c) (Up to MY 04) the Crankshaft Rear Seal Ring
- Engine Oil Change (Z 18 XE, Z 18 XEL, with AC, Lhd)
- How to Replace (Z 18 XE the Oil Filter Short Circuit Valve (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Seal Ring - Crankshaft, Front (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Oil Pan (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Oil Pump (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Oil Pump Pressure Regulating Valve (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Oil Intake Pipe (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Oil Dipstick Guide Tube (Z 18 XEL, with AC, Lhd))
- Sensor - Dynamic Oil Level Control (Z 18 XE, Z 18 XEL, with AC, Lhd)
- How to Check for Leaks the Engine ((CO Content in Cooling System) (Z 18 XE, Z 18 XEL))
- How to Replace (Z 18 XE the Engine Damping Blocks (Both Sides) (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Reaction Member - Front (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Reaction Member - Rear (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Engine Damping Block - Right (Z 18 XEL, with AC, Lhd))
- How to Replace (Z 18 XE the Engine Damping Block - Left (Z 18 XEL, with AC, Lhd))
- How to Remove and Install (Z 18 XE the Engine with Transmission (Z 18 XEL, with AC, Lhd))
- Engine Compartment Survey (Z 18 XE, Z 18 XEL)
- How to Check (Z 18 XE the Fuel Pressure (Z 18 XEL, with AC, Lhd))
- Checking and Adjustment Values
- Ribbed V-Belt
- Engine Timing
- Oil Circulation
- Crank Drive, Cylinder Block
- How to Measure (Z 32 SE) the Oil Temperature
- How to Check (Z 32 SE the Engine Oil Pressure (With AC, Lhd))
- How to Check (Z 32 SE the Fuel Pressure (With AC, Lhd))
- How to Check (Z 32 SE the Timing (With AC, Rhd))
- How to Adjust (Z 32 SE the Timing (With AC, Rhd))
- How to Check and Correct (Z 32 SE the Toothed Belt Tension (With AC, Rhd))
- How to Check the Ribbed V-Belt Tension
- Illustration Z 32 SE
- How to Replace (Z 32 SE the Ribbed V-Belt (With AC, Rhd))
- How to Replace (Z 32 SE the Ribbed V-Belt Tensioner (Assembly.) (With AC, Lhd))
- How to Replace (Z 32 SE the Rear Toothed Belt Cover (With AC, Rhd))
- How to Replace (Z 32 SE the Front Toothed Belt Cover (With AC, Rhd))
- How to Replace (Z 32 SE the Toothed Belt (With AC, Rhd))
- How to Replace (Z 32 SE the Toothed Belt Tension Roller (With AC, Rhd))
- How to Replace (Z 32 SE the Toothed Belt Guide Roller (With AC, Rhd))
- How to Replace (Z 32 SE the Toothed Belt Drive Gear (With AC, Rhd))
- How to Replace (Z 32 SE the Intake Plenum (With AC, Lhd))
- How to Replace (Z 32 SE the Intake Flange (With AC, Lhd))
- How to Remove and Install (Z 32 SE the Spark Plugs (With AC, Lhd))
- How to Replace (Z 32 SE the Gasket - Exhaust Manifold, Cylinder Head 1-3-5 (With AC, Lhd))
- How to Replace (Z 32 SE the Gasket - Exhaust Manifold, Cylinder Head 2-4-6 (With AC, Lhd))
- How to Replace (Z 32 SE the Camshaft Sprockets (With AC, Rhd))
- How to Remove and Install (Z 32 SE the Camshafts (With AC, Rhd))
- How to Replace (Z 32 SE the Seal Rings - Camshafts (With AC, Rhd))
- How to Remove and Install (Z 32 SE the Cylinder Head Cover (1-3-5) / (2-4-6) (With AC, Rhd))
- How to Remove and Install (Z 32 SE the Cylinder Heads (With AC, Rhd))
- How to Remove and Install (Z 32 SE the Flywheel (With AC, Rhd))
- How to Replace (Z 32 SE the Seal Ring - Crankshaft, Front (With AC, Rhd))
- How to Replace (Z 32 SE the Seal Ring - Crankshaft (Rear) (With AC, Rhd))
- Engine Oil with Filter Change (Z 32 SE)
- How to Replace (Z 32 SE the Oil Filter Short Circuit Valve (With AC, Lhd))
- How to Remove and Install (Z 32 SE the Oil Filter Housing (With AC, Lhd))
- How to Remove and Install (Z 32 SE the Oil Dipstick Guide Tube (With AC, Lhd))
- How to Remove and Install (Z 32 SE the Oil Pan (With AC, Rhd))
- How to Replace (Z 32 SE the Intake Pipe for Oil Pump (With AC, Rhd))
- How to Remove and Install (Z 32 SE the Oil Pump (With AC, Rhd))
- How to Overhaul (Z 32 SE the Oil Pump (With AC, Rhd))
- How to Remove and Install (Z 32 SE the Oil Pump Pressure Regulating Valve (With AC, Rhd))
- How to Replace (Z 32 SE the Pressure Relief Valve in Oil Circuit (With AC, Rhd))
- How to Replace (Z 32 SE the Heat Exchanger (With AC, Lhd))
- How to Replace (Z 32 SE the Engine Vent Housing (With AC, Lhd))
- How to Check for Leaks the Engine ((CO Content in Coolant) (Z 32 SE))
- Toothed Belt Diagnosis - Possible Causes and Remedys
- How to Replace the Engine Mounting (Engine Damping Block) (Both Sides)
- How to Replace (Z 32 SE the Reaction Member - Rear (With AC, Rhd))
- How to Replace (Z 32 SE the Reaction Member - Front (With AC, with Auxiliary Heating, Lhd))
- How to Remove and Install (Z 32 SE the Engine (With AC, with Auxiliary Heating, Lhd, At))
- How to Remove and Install (Z 32 SE the Engine (With AC, with Auxiliary Heating, Lhd, Mt))
- How to Remove and Install from Engine (Z 32 SE the Automatic Transmission (With AC, with Auxiliary Heating, Lhd))
- How to Remove and Install from Engine (Z 32 SE the Manual Transmission (With AC, with Auxiliary Heating, Lhd))
- Engine Compartment Survey Z 32 SE
- Sealants, Lubricants and Locking Compounds (V6)
- Checking and Adjustment Values - V6
- Oil Circuit - V6
- Ribbed V-Belt - V6
- Toothed Belt - V6
- Cylinder Head - V6
- Crank Drive, Cylinder Block (V6)
- DOHC Petrol Engine (Z 22 SE) Engine Number
- How to Check (Z 22 SE) the Ribbed V-Belt Tension
- How to Check (Z 22 SE the Compression (AC, Rhd, At))
- How to Check (Z 22 SE the Engine Oil Pressure (AC, Rhd, At))
- How to Measure (Z 22 SE) the Oil Temperature
- How to Check (Z 22 SE the Timing (AC, Rhd, At))
- How to Adjust (Z 22 SE the Timing (AC, Rhd, At))
- Illustration (Z 22 SE)
- How to Replace (Z 22 SE the Ribbed V-Belt (AC, Rhd, At))
- How to Replace (Z 22 SE the Ribbed V-Belt Tensioner (AC, Rhd, At))
- Toothbelt - Service Intervall Overview
- How to Remove and Install (Z 22 SE the Timing Case (AC, Rhd, At))
- How to Replace (Z 22 SE the Guide Rail (Primary Chain) (AC, Rhd, At))
- How to Replace (Primary Chain) (Z 22 SE the Hydraulic Chain Tensioner (AC, Rhd, At))
- How to Replace (Secondary Chain) (Z 22 SE the Hydraulic Chain Tensioner (AC, Rhd, At))
- How to Replace (Z 22 SE the Timing Chain (Primary) (AC, Rhd, At))
- How to Replace (Z 22 SE the Timing Chain (Secondary) (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Cylinder Head Cover (AC, Rhd, At))
- How to Replace (Z 22 SE the Camshaft Pulleys (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Both Camshafts (AC, Rhd, At))
- Replace Roller Cam Followers (Z 22 SE)
- Replace Hydraulic Valve Lifters (Z 22 SE)
- How to Replace (Z 22 SE the Gasket - Intake Manifold (AC, Rhd, At))
- How to Replace (Z 22 SE the Gasket - Exhaust Manifold (AC, Rhd, At))
- How to Replace (Z 22 SE the Cover - Camshaft Connection Flange (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Cylinder Head (AC, Rhd, At))
- Engine - Broken Timing Chain
- How to Replace (Z 22 SE the Pressure Relief Valve in Intake Manifold (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Drive Disc (AC, Rhd, At))
- How to Replace (Z 22 SE the Torsional Vibration Damper (AC, Rhd, At))
- How to Replace (Z 22 SE the Seal Ring - Crankshaft (Front) (AC, Rhd, At))
- How to Replace (Z 22 SE the Seal Ring - Crankshaft, Rear (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Oil Pump (AC, Rhd, At))
- How to Check (Z 22 SE the Oil Pump (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Oil Pan (AC, Rhd, At))
- Additional Operation for Replacing the Oil Pan (Z 22 SE, AC, Rhd, At)
- How to Remove and Install (Z 22 SE the Oil Pump Pressure Regulating Valve (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Oil Dipstick Guide Tube (AC, Rhd, At))
- How to Replace (Z 22 SE the Oil Pressure Switch (AC, Rhd, At))
- Replace Oil Filter Short Circuit Valve
- How to Replace (Z 22 SE the Oil Spray Nozzles (Timing Chain) (AC, Rhd, At))
- How to Check for Leaks the Engine ((CO Content in Coolant) (Z 22 SE))
- How to Replace the Engine Mounting (Engine Damping Block) (Both Sides (Z 22 SE, AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Reaction Member - Front (Engine Damping Block) (AC, Rhd, At))
- How to Remove and Install (Z 22 SE the Reaction Member - Rear (Engine Damping Block) (AC, Rhd, At))
- How to Replace the Engine Mounting (Engine Damping Block) (Right Side (Z 22 SE, AC, Rhd, At))
- How to Replace the Engine Mounting (Engine Damping Block) (Left Side (Z 22 SE, AC, Rhd, At))
- Engine Compartment Survey (Z 22 SE)
- How to Remove and Install (Z 22 SE the Spark Plug (AC, Rhd, At))
- Z18XE Engine - No Compression Because of a Broken Valve Spring
- Spark Plug Damages - Possible Causes and Failure Modes
- How to Check and Measure the Cylinder Head and Attaching Parts (Cylinder Head, Overhaul)
- How to Replace (Z 16 XE the Ribbed V-Belt (With AC, Lhd))
- Engine Oil with Filter Change
- Check Engine Compression Loss (Z 16 XE)
- Replace One Con-Rod (Z 16 ZE, No A/c, Lhd)
- Measure Crankshaft (Z 16 XE)
- Repair Engine Using a Part Engine (Z 16 XE, Without AC, Lhd)
- How to Check (Z 18 XE the Engine Pressure Loss (Z 18 XEL))
- How to Remove and Install (Z 18 XE the Camshaft Sprocket (Z 18 XEL with AC, Lhd))
- How to Replace (Z 18 XE the One Con-Rod Bearing (Z 18 XEL, Without AC, Lhd))
- How to Measure (Z 18 XE the Crankshaft (Z 18 XEL))
- Repair Engine Using a Part Engine (Z 18 XE, Z 18 XEL with AC, Lhd)
- Manual Transmission, Detach and Attach From/to Engine (Z 18 XE, Z 18 XEL, with AC, Lhd)
- How to Check (Z 32 SE the Engine Pressure Loss (With AC, Lhd))
- How to Measure (Engine Dismantled) the Crankshaft
- How to Remove and Install (Z 32 SE the Drive Disc (With AC, with Auxiliary Heating, Lhd))
- How to Replace the Piston Rings
- How to Replace (Z 32 SE) the One Con-Rod Bearing
- Repair Engine Using an Engine Short Block
- How to Check (Z 22 SE the Engine Pressure Loss (AC, Lhd, At))
- Engine Z28NEL/Z28NET, Oil Leakages (Oil Traces at Oilpain/transmission Housing)
- Engine Z16XER, Z18XER (Camshaft Bearing Bridge Leaky)
- Engine Z22SE/Z22YH, Tensioner Timing Chain (Rattling Noise from Timing Chain)
- Engine Z16/18XER, Cylinderhead (Oil Leakage Between Camshaft Bearing Bridge and Camshaft Cover)
- Replace All Valve Shaft Seals (Z 16 XE, with A/c, Lhd).
- Remove and Refit All Pistons with Con-Rods (Z 16 XE, with A/c, Lhd)
- DOHC Petrol Engine (Z 20 NET) Engine Number
- Check Ribbed V-Belt Tension (Z 20 NET)
- Check Compression (Z 20 NET, AC, Rhd, Mt)
- Check Engine Oil Pressure (Z 20 NET, AC, Rhd, Mt)
- Measure Oil Temperature (Z 20 NET)
- Check Timing (Z 20 NET, AC, Rhd, Mt)
- Adjust Timing (Z 20 NET, AC, Rhd, Mt)
- Replace Ribbed V-Belt (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Timing Case (Z 20 NET, AC, Rhd, Mt)
- Replace Guide Rail (Primary Chain) (Z 20 NET, AC, Rhd, Mt)
- Replace Hydraulic Chain Tensioner (Primary Chain) (Z 20 NET, AC, Rhd, Mt)
- Replace Timing Chain (Primary) (Z 20 NET, AC, Rhd, Mt)
- Replace Hydraulic Chain Tensioner (Secondary Chain) (Z 20 NET, AC, Rhd, Mt)
- Replace Timing Chain (Secondary) (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Cylinder Head Cover (Z 20 NET, AC, Rhd, Mt)
- Replace Camshaft Sprocket (One or Both) (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Both Camshafts (Z 20 NET, AC, Rhd, Mt)
- Replace Roller Cam Follows (Z 20 NET)
- Replace Hydraulic Tappets (Z 20 NET)
- Replace Intake Manifold Gasket (Z 20 NET, AC, Rhd, Mt)
- Replace Camshaft Connecting Flange Cover (Z 20 NET, AC, Rhd, Mt)
- Replace Exhaust Manifold (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Cylinder Head (Z 20 NET, AC, Rhd, Mt)
- Replace Vacuum Pump (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Flywheel (Z 20 NET, AC, Rhd, Mt)
- Replace Flywheel (Z 20 NET, AC, Rhd, Mt)
- Replace Front Crankshaft Sealing Ring (Z 20 NET, AC, Rhd, Mt)
- Replace Crankshaft Sealing Ring (Rear) (Z 20 NET, Mt, AC, Rhd, Mt)
- Remove and Refit Oil Pan (Z 20 NET, AC, Rhd, Mt)
- Extra Work When Replacing the Oil Pan (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Oil Pump Pressure Control Valve (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Oil Pump (Z 20 NET, AC, Rhd, Mt)
- Check Oil Pump (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Oil Dipstick Tube (Z 20 NET, AC, Rhd, Mt)
- Replace Oil Pressure Switch (Z 20 NET, AC, Rhd, Mt)
- Replace Oil Injector (Timing Chain) (Z 20 NET, AC, Rhd, Mt)
- Replace Oil Supply Pipe to Turbo (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Engine Oil Cooler (Z 20 NET, AC, Rhd, Mt)
- How to Check for Leaks the Engine ((CO Content in Coolant) (Z 20 NET))
- How to Replace the Engine Mounting (Engine Damping Block) (Both Sides (Z 20 NET, AC, Rhd, Mt))
- Replace Rear Engine Mounting (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Front Torque Connection (Engine Mounting) (Z 20 NET, AC, Rhd, Mt)
- How to Replace the Engine Mounting (Engine Damping Block) (Right Side (Z 20 NET, AC, Rhd, Mt))
- How to Replace the Engine Mounting (Engine Damping Block) (Left Side (Z 20 NET, AC, Rhd, Mt))
- Remove and Refit Gearbox to Engine (Z 20 NET, AC, Rhd, Mt)
- Replace Fuel Distribution Pipe (Z 20 NET, AC, Rhd, Mt)
- Check Fuel Pressure (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Spark Plugs (Z 20 NET, AC, Rhd, Mt)
- Replace Intake Manifold Pressure Sensor (Z 20 NET, AC, Rhd, Mt)
- Remove and Refit Alternator (Z 20 NET, AC, Rhd, Mt)
- Oil Circuit
- Engine Z18XER - Rattling Noise from Poly-V-Belt
- DOHC Petrol Engine (Z 22 YH) Engine Number
- Check Ribbed V-Belt Tension (Z 22 YH)
- Check Compression (Z 22 YH, AC, Lhd, At)
- Check Engine Pressure Loss (Z 22 YH, AC, Lhd, At)
- How to Check (Z 22 YH the Engine Oil Pressure (AC, Rhd, At))
- Measure Oil Temperature (Z 22 YH)
- Check Timing (Z 22 YH, Lhd, AC)
- Adjust Timing (Z 22 YH, Lhd, AC)
- How to Replace (Z 22 YH the Ribbed V-Belt (AC, Rhd, At))
- How to Remove and Install (Z 22 YH the Ribbed V-Belt Tensioner (Lhd, AC))
- Remove and Refit Timing Case (Z 22 YH, Lhd, AC)
- Replace Guide Rail (Primary Chain) (Z 22 YH, Lhd, AC)
- Insert Hydraulic Chain Tensioner (Primary) (Z 22 YH, Lhd, AC)
- Insert Hydraulic Chain Tensioner (Secondary Chain) (Z 22 YH, Lhd, AC)
- Replace Timing Chain (Primary) (Z 22 YH, Lhd, AC)
- Replace Timing Chain (Secondary) (Z 22 YH, Lhd, AC)
- Remove and Cylinder Head Cover (Z 22 YH, Lhd, AC)
- Replace a Further Camshaft Sprocket (Z 22 YH, Lhd, AC)
- Replace Camshaft Sprocket (Z 22 YH, Lhd, AC)
- Remove and Refit Both Camshaft (Z 22 YH, Lhd, AC)
- Replace Roller Cam Followers (Z 22 YH)
- Replace Hydraulic Tappets (Z 22 YH)
- Replace Intake Manifold Gasket (Z 22 YH, Lhd, AC)
- How to Replace (Z 22 YH the Gasket - Exhaust Manifold (AC, Rhd, At))
- Remove and Refit Cylinder Head (Z 22 YH, AC, Lhd, At)
- Replace High Pressure Fuel Pump (Z 22 YH, Lhd, AC)
- How to Remove and Install (Z 22 YH the Drive Disc (AC, Rhd, At))
- Replace Torsional Vibration Damper (Z 22 YH, Lhd, AC)
- Replace Crankshaft Sealing Ring Front (Z 22 YH, Lhd, AC)
- How to Replace (Z 22 YH the Seal Ring - Crankshaft (Rear) (AC, Rhd, At))
- How to Remove and Install (Z 22 YH the Oil Pump (AC, Rhd, At))
- How to Check (Z 22 YH the Oil Pump (AC, Rhd, At))
- How to Remove and Install (Z 22 YH the Oil Pan (AC, Rhd, At))
- Additional Operation for Replacing the Oil Pan (Z 22 YH, AC, Rhd, At)
- How to Remove and Install (Z 22 YH the Oil Pump Pressure Regulator (AC, Rhd, At))
- How to Remove and Install (Z 22 YH the Oil Dipstick Guide Tube (AC, Rhd, At))
- How to Replace (Z 22 YH the Oil Pressure Switch (AC, Rhd, At))
- Replace Oil Spray Nozzle (Timing Chain) (Z 22 YH, Lhd, AC)
- How to Check for Leaks the Engine ((CO Content in Coolant) (Z 22 YH))
- How to Replace (Z 22 YH the Coolant Piper (AC, Rhd, At))
- How to Replace (Z 22 YH the Control Unit Coolant Module (AC, Rhd, At))
- How to Replace the Engine Mounting (Engine Damper Block) (Both Sides (Z 22 YH, Lhd, AC))
- How to Remove and Install (Z 22 YH the Reaction Member - Front (Engine Damping Block) (AC, Rhd, At))
- How to Remove and Install (Z 22 YH the Reaction Member - Rear (Engine Damping Block) (AC, Rhd, At))
- How to Replace the Engine Mounting (Engine Damper Block) (Right Side (Z 22 YH, Lhd, AC))
- How to Replace the Engine Mounting (Engine Damping Block) (Left Side (Z 22 YH, AC, Rhd, At))
- How to Replace (Z 22 YH the Oxygen Sensor - Catalytic Converter Control (AC, Rhd, At))
- Remove and Refit Spark Plugs (Z 22 YH, Lhd, AC)
- Replace Camshaft Sensor (Z 22 YH, Lhd, AC)
- Torque Guide Values
- How to Replace (Z 18 XE the All Valve Stem Seals (Z 18 XEL, with AC, Lhd))
- Remove and Refit All Pistons with Con-Rods (Z 18 XE, Z 18 XEL, with A/c, Lhd)
- Remove and Refit All Pistons with Con-Rods (Z 22 SE, AC, Lhd, At)
- Replace Piston Rings (Z 22 SE)
- Replace One Piston And/or Con-Rod (Piston Removed with Con-Rod) (Z 22 SE)
- Replace All Valve Stem Seals (Z 32 SE)
- Remove and Refit All Pistons with Con-Rods (Z 32 SE, with A/c, Rhd)
- Replace Pistons
- How to Remove and Install (Z 16 XE the Spark Plugs (With AC, Lhd))
- Check Engine Pressure Loss (Z 20 NET, Lhd, AC)
- How to Remove and Install (Z 18 XE the Spark Plugs (Z 18 XEL, with AC, Lhd))
- Repair Radiator Fastening Pin
- How to Remove and Install (Z 32 SE the Crankshaft (With Air Conditioning))
- Engine Compartment Overview (Z 20 NET)
- How to Replace (Z 20 NET the All Valve Stem Seals (AC, Rhd, Mt))
- How to Replace (Piston with Con-Rod Removed) (Z 20 NET) the One Piston And/or Con-Rod
- How to Replace (Z 22 SE the All Valve Stem Seals (AC, Rhd, At))
- How to Replace (Z 22 YH) the All Valve Stem Seals
- How to Remove and Install (Z 22 YH) the All Pistons with Con-Rods
- How to Replace (Piston Removed with Con-Rod) (Z 22 YH) the One Piston And/or Con-Rod
- Engine Compartment Overview (Z 22 YH)
- Repair Upper Radiator Fastening Pin
- Repair Lower Radiator Fastening Pin
- Illustration Secondary Air System (Up to MY 2007)
- Illustration of Vacuum Hoses
- Illustration Timing Chain Level 1 (Z28NEL, Z28NET Up to MY 2006)
- Illustration Timing Chain Level 2 (Z28NET as of MY 2007)
- Illustration of Coolant Hoses
- Replace Air Cleaner Housing
- Replace Air Intake Pipe
- Replace Ribbed V-Belt
- Replace Ribbed V-Belt Tensioner
- Remove and Install Timing Case Cover (Up to MY 2007)
- Remove and Install Torsional Vibration Damper
- Remove and Install Intake Manifold Upper Part
- Remove and Install Intake Manifold Lower Part
- Replace Exhaust Manifold Heat Shield for Cylinders 1, 3 and 5
- Replace Exhaust Manifold Gasket for Cylinders 1-3-5 (Z28NEL, Z28NET Up to MY 2007)
- Remove and Install Cylinder Head Cover for Cylinders 1, 3 and 5
- Remove and Install Cylinder Head Cover of Cylinder 2-4-6 (Z28NEL, Z28NET Up to MY 2007)
- Replace (Front) Crankshaft Seal Ring
- Replace (Rear) Crankshaft Seal Ring
- Remove and Install Oil Filter Housing
- Replace Oil Intake Pipe
- Replace Engine Oil Filler Port
- Replace Turbo Oil Return Line
- Replace Secondary Air System Pump
- Replace Rear Engine Damping Block
- Replace Front Engine Damping Block
- Replace Right-Hand Engine Damping Block
- Replace Left-Hand Engine Damping Block
- How to Remove and Install the Manual Transmission from Engine
- Illustration of Air Ducts
- Illustration of Thread Repair - Upper Side of Cylinder Head 2-4-6
- Illustration of Thread Repair - Front Side of Cylinder Head 2-4-6
- Illustration of Thread Repair - Intake Side of Cylinder Head 2-4-6
- Illustration of Thread Repair - Exhaust Side of Cylinder Head 2-4-6
- Illustration of Thread Repair - Back of Cylinder Head 2-4-6
- Illustration of Thread Repair - Upper Side of Cylinder Head 1-3-5
- Illustration of Thread Repair - Front Side of Cylinder Head 1-3-5
- Illustration of Thread Repair - Intake Side of Cylinder Head 1-3-5
- Illustration of Thread Repair - Exhaust Side of Cylinder Head 1-3-5
- Illustration of Thread Repair - Back of Cylinder Head 1-3-5
- Illustration of Thread Repair - Front Side of Cylinder Block
- Illustration of Thread Repair - Cylinder Block Side of Cylinders 2-4-6
- Illustration of Thread Repair - Cylinder Block Side of Cylinders 1-3-5
- Illustration of Thread Repair - Back of Cylinder Block
- Illustration of Thread Repair - Underside of Cylinder Block
- Illustration of Thread Repair - Upper Side of Cylinder Block, Cylinders 2-4-6
- Illustration of Thread Repair - Upper Side of Cylinder Block, Cylinders 1-3-5
- Illustration of Thread Repair - Timing Case Cover
- Engine Code / Engine Number
- Check Engine for Leaks (CO Content of Coolant)
- Check Fuel Pressure
- How to Check the Engine Oil Pressure
- Check Ribbed V-Belt Tensioner
- Check Engine Compression Loss
- How to Check the Compression
- How to Replace the Guide Rail (Secondary Chain) of Cylinders 1-3-5
- How to Replace the Guide Rail (Secondary Chain) of Cylinders 2-4-6
- How to Replace the Guide Rail (Primary Chain, Top)
- How to Replace the Tensioning Rail (Secondary Chain) of Cylinders 1-3-5
- How to Replace the Tensioning Rail (Secondary Chain) of Cylinders 2-4-6
- How to Remove and Install the Automatic Transmission from Engine
- How to Replace the Engine Oil Level Sensor
- Repair of Standard Threads
- Repairing the Thread of the Crankshaft Main Bearing Cover (Outer Bolts)
- Repairing the Thread of the Crankshaft Main Bearing Cover (Inner Bolts)
- Repairing Countersunk Threads
- Repairing Tapered Threads
- Repairing the Thread of Cylinder Head Bolts
- Check Oil Pressure
- Check Engine for Leaks (CO Content in Cooling System)
- Replace Resonator
- Replace Toothed Belt Cover (Upper)
- Adjust Timing
- Remove and Install Cylinder Head Cover
- Replace Camshaft Sprockets
- How to Remove and Install the Both Camshafts
- Check Valve Lash and Adjust
- Replace Camshaft Sealing Ring
- Replace Exhaust Manifold Gasket
- Replace Intake Manifold Gasket
- Detaching and Attaching Components, Cylinder Head
- Remove and Install Valve Lifters
- Engine Oil with Oil Filter Change
- Remove and Install Oil Pan
- Replace Oil Dipstick Guide Tube
- Replace Engine Damping Block (Front)
- Dohc-I Sealing, Lubricating and Locking Materials
- Test and Adjustment Values - Dohc-I
- Toothed Belt
- Remove and Install Air Cleaner Housing
- Replace Front Upper Toothed Belt Cover
- Replace Front Centre Toothed Belt Cover
- Replace Engine Breather Pipe
- Replace Valves - Camshaft Adjustment
- Replace Con-Rod Bearing
- Check Con-Rod Play (With Plastigage)
- Check Con-Rod Bearing Play (With External Micrometer and Internal Measuring Instrument)
- Check Crankshaft Longitudinal Play
- Check Crankshaft Out-Of-Roundness
- Check Crankshaft Bearing Play (With Plastigage) -
- Check Crankshaft Bearing Play (With Micrometer and Interior Measuring Instrument)
- Remove and Install Oil Dipstick Tube
- Replace Oil Pressure Switch
- Replace Oil Pressure Control Valve
- Replace Pressure Relief Valve
- Remove and Install Spark Plugs
- How to Remove and Install the Drive Disc
- Replace All Con-Rod Bearings
- Check Crankshaft Bearing Play (With External Micrometer and Interior Measuring Instrument)
- Check Cylinder Block for Plane Surface
- How to Remove and Install the Oil Pump
- Replace Oil Spray Nozzle
- Replace Ribbed V-Belt Tensioner (Z 20 NET, AC, Rhd, Mt)
- How to Remove and Install the Camshafts
- How to Remove and Install the Attachments
- Replace Toothed Belt Tensioner
- Replace Toothed Belt Deflector Roller
- How to Replace the Intake Manifold Flange
- Make Holes for Adapter KM-412-31
- How to Replace (From MY 05) the Crankshaft Rear Seal Ring
- How to Replace (New Version from MY 2005) the Crankshaft Seal Ring (Rear)
- How to Remove and Install the Exhaust Duct Cover
- Replace Toothed Belt
- How to Check the Timing
- Illustration Secondary Air System (As of MY 2008)
- Illustration Timing Chain Level 1 (Z28NET as of MY 2007)
- Illustration Timing Chain Level 2 (Z28NEL, Z28NET Up to MY 2006)
- Remove and Install Timing Case Cover (As of MY 2008)
- Replace Exhaust Manifold Gasket for Cylinders 1-3-5 (Z28NET as of MY 2008)
- Remove and Install Cylinder Head Cover of Cylinders 2-4-6 (Z28NET as of MY 2008)
- Replace Camshaft Sprocket Exhaust Side for Cylinders 1-3-5 (Z28NEL, Z28NET Up to MY 2006)
- Replace Camshaft Sprocket Exhaust Side for Cylinders 2-4-6 (Z28NEL, Z28NET Up to MY 2006)
- Camshaft Marking
- ABS
- ABS 430
- ABS 5.3
- ABS 5.3/TC/ESP
- ABS 5/TC, ABS 5.3/TC
- ABS Mk20i
- Air Conditioning
- Airbag
- Anti-Theft Warning System-M
- Automatic Transmission Front Wheel Drive
- Battery
- Board Computer
- Body Equipment
- Brake Hydraulics, Brake Lines
- Brakes
- CAN Bus
- Car Level Control
- Central Door Locking System
- Central Locking with Atws (Electronic)
- Check Control
- Clutch
- Clutch and Transmission
- Communication / Navigation
- Connector pinouts
- Continuously Variable Transmission (Cvt) Front Drive
- Cooling System
- Corrosion Protection
- Diesel Engine
- DOHC Diesel Engine
- DOHC Petrol Engine
- Ecc Electronic Climate Control
- Ehps - Electrical Hydraulic Power Steering
- Electrical Equipment and Instruments
- Electrical Socket Front/ Rear
- Electrical Window Winders
- Electronic Cruise Control
- Electronic Module
- Electronic Ride Control
- Engine and Engine Aggregates
- Engine Electrics
- Eps Electrical Power Steering
- Exhaust System
- Fittings, Hinges, Locks
- Frame
- Front End
- Front Wheel Brake
- Front Wheel Suspension
- Front Wheel Suspension, Wheels and Tyres
- Fuel and Exhaust System
- Fuel Injection Systems
- Fuel System
- Fuse Box
- General Vehicle Information
- Glass, Window Guides, Window Winders
- Glassfibre Parts (Bolted)
- Graphic Info Display
- Headlamps, Lamps and Horn
- Heating, Ventilation
- Heating, Ventilation, Air Conditioning (HVAC)
- Immobiliser
- Instruments, Telltales
- Maintenance, Body and Chassis Sheet Metal Parts, Frame
- Manual Transmission Front Wheel Drive
- Manual Transmission Rear Wheel Drive
- Mid (Multi Info Display)
- Other Accessories
- Outside Rear View Mirror
- Paint
- Painting Repair Operations
- Painting Repair System
- Parkpilot
- Power Steering
- Radiator Grille
- Radio
- Rear Axle and Rear Wheel Suspension
- Rear Axle Front Wheel Drive
- Rear Wheel Brake
- Roof Luggage Carrier (Railing)
- Sac Semi Automatic Climate Control
- Seat Heating Systems
- Seats, Upholstery, Inner Trim Panels
- Service Brake, Parking Brake
- Servo Motors
- Sheet Metal Parts (Bolted)
- Sheet Metal Parts (Cement and Seal)
- Sheet Metal Parts (Welded)
- Sliding Roof
- Steering
- Steering Gear
- Steering Intermediate Shaft
- Steering Linkage
- Steering Wheel - Steering Column
- Switches
- Switches, Control Unit, Relays, Ignition Lock
- TID (Triple Info Display)
- Trailer Hitch
- Trim Panels, Radiator Grille, Spoiler
- Trim Strips, Lettering, Coverings
- Turbo-Charging
- Wheels and Tyres
- Windscreen Wash/wipe System, Heated Screen
- Wiring Harnesses
- Xenon Control Unit (Headlamp Range Control)