Alternator, Disassemble
| .D. ICON01.tif | 0,75 | 0,75 | tiff;; Remove, Disconnect |
Alternator - see corresponding operation.
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
Cable from rear cover - rubber cap and nut; clip.
| Vacuum pump from rear cover - three bolts. | |||
|---|---|---|---|
| .P. U2538.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Through bolts (arrowed) - mark position of front and rear housings relative to stator. | |||
| .P. C7325.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Front housing with armature from stator and rear housing - use screwdriver to carefully separate. | |||
| .P. C7207.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Nuts (arrowed) securing that secure stator to rear housing. | |||
| .P. C7208.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Stator with diode plate and brush holder from rear housing - use screwdriver to carefully lever out. | |||
| .P. C7211.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Pulley nut from armature - use soft - jawed vice. | |||
| .P. U2536.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Pulley, fan spacer and front housing from armature. | |||
| .P. C7218.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Bearing from armature - use puller. | |||
| .P. C5911.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Bearing retainer from front housing - screws (arrowed). | |||
| .P. C7212.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Bearing from front housing - press out manually or drive out with suitable drift. | |||
| .P. C7213.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Seal from rear housing - use screwdriver. | |||
| .P. C7214.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
Stator leads from diode plate - unsolder connections (arrowed).
| .D. ICON11.tif | 0,75 | 0,75 | tiff;; Important! |
|---|---|---|---|
| Hold wire to diode with long - nose pliers to prevent overheating of diode. | |||
| .P. C7215.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Brush holder from diode plate - insulating sleeve and bolt (A), and unsolder connection (arrowed). | |||
| .P. C7216.tif | 9 | 7,5 | tiff;; |
| .D. ICON03.tif | 0,75 | 0,75 | tiff;; Disassemble |
| Regulator from brush holder - unsolder connections. | |||
| .P. U2532.tif | 9 | 7,5 | tiff;; |