Home ReviewsRefund
Home/Opel/Vectra/Opel Vectra C (2002-2008)/Repair manual/DOHC Diesel Engine/Special Service Tools
Contents Wiring diagrams Section: DOHC Diesel Engine All sections

Special Service Tools Opel Vectra C

DOHC Diesel Engine 69 illustrations
EN-47646Locking Device
Locking the toothed belt drive wheel
EN-47656-1Compression test plug - connection
Checking leaks in the charge-air system in conjunction with tyre inflator
EN-47656-2Compression test plug
Checking leaks in the charge-air system in conjunction with tyre inflator
KM-161-BRemover
Pushing tie rod joint out of steering knuckle
KM-301Measuring Bridge
To check piston projection
KM-412-AEngine Overhaul Stand
To hold removed engine
KM-412-33Engine adapter
Engine mounting in conjunction with KM-412-A
KM-468-BHolding Wrench
To counterhold wheel hub
KM-470-BAngular Torque Wrench
Tightening screwed joints by applying torque
MKM-558-10Closure cover
Sealing the brake fluid reservoir when opening the brake system
MKM-571-BDial gauge
KM-574Remover/Installer
Flywheel removal/installation
MKM-596-ATemperature Gauge
MKM-604-DTorx Bit and Socket Set
Removal, installation of Torx bolts, nuts
KM-609Electronics kit
Diagnosis of electronic and electrical systems
MKM-610Torque wrench 1/2"
Range 30 – 130 Nm
MKM-611Torque wrench 3/8"
Range 10 – 60 Nm
KM-652Locking Device
To lock flywheel or drive disc
MKM-667Pressure and Vacuum Pump
To check vacuum systems for leaks
MKM-669Torque wrench 1/2"
Range 50 – 300 Nm
KM-796-AInstallation Clamp
To open quick-release fittings for fuel system
KM-807Closure Plugs
To seal off fuel lines
KM-828Guide
Installing the con-rod on the crankshaft
KM-845Suction Tool
Removal of valve lifters, adjusting discs
MKM-883-1Engine Bridge
To hold / lower / lift engine
MKM-883-2Adapter Plate
Holding the engine in conjunction with MKM-883-1 and MKM-883-3
MKM-883-3Adapter Plate
Holding the engine in conjunction with MKM-883-1 and MKM-883-2
KM-904Base Frame
To remove/install engine and transmission with KM-6312
KM-2358Wire Cable
Suspending the engine or the transmission
KM-6015Closure Plugs
Sealing off fuel lines
KM-6086Basic kit
Remove/refit valve shims
KM-6182-1Pliers, straight
Removal/installation of compact clamps
KM-6182-2Pliers, curved
Removal/installation of compact clamps
KM-6182-3Pliers, flexible shaft
Removal/installation of compact clamps
KM-6312Centring Tool
Vehicle underbody, with KM-904 and hydraulic jack
KM-6313Engine/Transmission Mount
KM-6320Closure Plugs
Sealing off fuel lines
KM-6326Closure Plugs
Closing the oil cooler line (yellow) and transmission opening (green)
KM-6347Holder
Torsional vibration damper
KM-6349Locating pin
Fixing the toothed belt tensioning device
KM-6352Engine mounting
Holding engine for removal/installation and work on engine timing side in the vehicle, in conjunction with KM-6313
KM-6369Remover/Installer
Removing and installing main bearing cover
KM-6370Remover/Installer
For removing and installing the upper valve seal ring, injector nozzle
KM-6371Installer
For installing the valve seal ring, fuel line
KM-6373Connection piece
Checking compression
KM-6374Oil Filter Wrench
To remove and install oil filter
KM-6375Installer
To install front crankshaft seal ring
KM-6376Installer
To install injection pump seal ring
KM-6377Installer
To install camshaft seal ring
KM-6378Adjuster
To adjust the camshaft sprockets
KM-6379Bracket
To fix the camshaft belt pulley in conjunction with KM-956-1
EN-46797Tool for holding down valve
Pressing down the valve lifter in conjunction with EN-46799
EN-46799Fixing tool
Fixing the valve lifter in the lower position in conjunction with EN-46797
KM-6385Installer
Installing the valve stem seals
KM-6386Remover/Installer
Removing and installing the valve guides
KM-6387Adapter
Tensioning the valve springs with KM-348 (cylinder head removed)
KM-6388Bracket
Securing the torque converter against slipping
MKM-J-6459-BTorque wrench 3/8"
Range 0 – 11 Nm
MKM-6600-1Torque wrench 4-40 Nm
Small torque wrench with low torque range for use in constricted areas, in conjunction with MKM-6600-100, MKM-6600-200 and MKM-6600-300
MKM-6600-2Torque wrench 20-120 Nm
Large torque wrench with high torque range for use in constricted areas, in conjunction with MKM-6600-100, MKM-6600-200 and MKM-6600-300
MKM-6600-100Open-ended Torx wrench set
Size: E8, E10, E11, E12, E14, E16, E18, E20, E22, E24 for use in constricted areas, in conjunction with MKM-6600-1 and MKM-6600-2
MKM-6600-200Open-ended ring spanner set
Sizes: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for use in constricted areas, in conjunction with MKM-6600-1 and MKM-6600-2
MKM-6600-300Open-ended spanner set
Sizes: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for use in constricted areas, in conjunction with MKM-6600-1 and MKM-6600-2
KM-6611Closure Plugs
Sealing the injector shafts for changing the valve stem seals with the cylinder head installed
KM-8066Remover
To remove rear crankshaft seal ring
KM-8068Installer
To install rear crankshaft seal ring
KM-J-37228Separation Tool
Detaching the oil pan
KM-J-41623-BRelease tool
Releasing fluid cooler line at radiator
KM-J-45000Remover
To remove various seal rings

More articles — Engine and Engine Aggregates