Home ReviewsRefund
Home/Opel/Meriva/Opel Meriva A (2003-2011)/Repair manual/DOHC Petrol Engine/Special Service Tools
Contents Wiring diagrams Section: DOHC Petrol Engine All sections

Special Service Tools Opel Meriva A

DOHC Petrol Engine 45 illustrations
KM-161-BRemover
Push head of tie rod out of steering knuckle
KM-313Slide Hammer
To remove axle shafts in conjunction with KM-902
KM-412-AEngine Overhaul Stand
To hold removed engine
KM-412-31Engine adapter
Engine support in conjunction with KM-412-A
KM-422Installer
To press seal ring in camshaft
KM-427Removing, installing tool
To install guide pins into engine block
KM-468-BHolding Wrench
Counterhold wheel hub when fitting axle nut
KM-470-BAngular Torque Wrench
To tighten cylinder head bolts
KM-471Adapter
To check pressurised cooling system in conjunction with cooling system tester
KM-498-BOil pressure gauge
To check engine oil pressure in conjunction with KM-135
KM-527-ASetting rod
Gear stick catch
MKM-558-10Closure Cap
Sealing brake fluid tank when opening brake system
MKM-571-BDial gauge
To check various components
MKM-596-ATemperature gauge
To measure oil temperature
MKM-604-DTorx Bit and Socket Set
To remove/install Torx bolts
KM-609Electronic Kit I
To diagnose electrical and electronic systems
MKM-610Torque Wrench 1/2"
Range 30 – 130 Nm / 22 – 96 lbf. ft.
MKM-611Torque Wrench 3/8"
Range 10 – 60 Nm / 7 – 44 lbf. ft.
KM-652Flywheel Holder
To lock flywheel or drive disc
MKM-667Pressure and Vacuum Pump
To check for leaks in vacuum unit
MKM-669Torque Wrench 1/2"
Range 50 – 300 Nm / 37 – 221 lbf. ft.
KM-796-ADismantler
To open quick-release fittings for fuel system
KM-840Remover
Removing the valve stem seal
KM-845Suction Device
To remove the hydraulic valve lifters
KM-902Remover
To remove axle shafts in conjunction with KM-313
KM-904Base Frame
To remove and install various vehicle components with additional adapters
KM-956-1Grip
Holding camshaft timing gears to loosen/tighten bolts in conjunction with KM-6347
KM-958Installer
Installing the valve stem seal
KM-2358Wire Cable
To suspend engine
KM-6009Remover/Installer
To remove/install ignition module
MKM-6086Automatic Valve Spring Lever
Removing/installing valve springs and valve cotters
KM-6168Subframe centring
KM-6179Remover/Installer
Removal/installation of oxygen sensor in manifold using MKM-611
KM-6333Locating Pin
Fixing toothed belt tensioner
KM-6340Locking Tool
Fixing camshaft timing gears to check and adjust control times
KM-6349Locating Pin
To fix tensioning pulley of ribbed V-belt
KM-6351Assembly Sleeves
To install crankshaft front seal ring (DOHC-I engine, 3rd gen.)
KM-6361Feeler gauge set
To measure valve play (DOHC-I engine, 3rd gen.)
KM-6363Spark Plug Key
To remove, install spark plugs (DOHC-I engine, 3rd generation)
KM-6394Engine/Transmission Mount
Fixing of engine/transmission to front axle body
KM-6623Installer
Installation of crankshaft seal ring, transmission side
KM-6624Remover
Removing crankshaft seal ring, transmission side
KM-6625Flywheel Holder
To lock flywheel, transmission installed
KM-J-34730-91Pressure Tester
To check fuel pressure
KM-J-45000Remover
Removal of various sealing rings

More articles — Engine and Engine Aggregates