Home ReviewsRefund
Home/Opel/Corsa/Opel Corsa D (2007-2011)/Repair manual/DOHC Diesel Engine/Special Service Tools
Contents Wiring diagrams Section: DOHC Diesel Engine All sections

Special Service Tools Opel Corsa D

DOHC Diesel Engine 62 illustrations
CH-47658Clamping too
To remove the fastening nuts of the tie rod ends
CH-48373Fixture engine / transmission / front axle
To remove, install and fix in position the engine, transmission and front axle in conjunction with KM-904 and the hydraulic jack
DT-48489Special socket, width: 36
To loosen and tighten the drive shaft retaining nuts
KM-161-BPusher tool
To press out the tie rod end from the axle knuckle
KM-313Slide Hammer
To pull the left axle shaft from the transmission
KM-6003Remover
Remove left axle shaft in conjunction with KM-313
KM-301Measuring bridge
Measure the piston projection
KM-412-AEngine Overhaul Stand
To hold the removed engine
KM-412-32Engine adapter
To hold engine in conjunction with KM-412-A
KM-468-BHolding Wrench
To counterhold wheel hub
KM-470-BAngular Torque Wrench
Tightening cylinder head bolts according to angle°
KM-471Adapter
Check pressurised cooling system in conjunction with cooling system tester
KM-498-BOil Pressure Manometer
To check engine oil pressure in conjunction with KM-232
KM-507-CPusher tool
To press tie rod end out of steering knuckle
MKM-596-ATemperature gauge
MKM-604-DTorx Bit and Socket Set
Removing and installing Torx bolts/nuts
MKM-610Torque Wrench, 1/2"
Range 30 - 130 Nm
MKM-611Torque Wrench – 3/8" drive.
Range 10 - 60 Nm
KM-652Flywheel Locking Device
Locking the flywheel
KM-662-CHolding Wrench
Counterholding the belt pulley/crankshaft
MKM-669Torque Wrench, 1/2"
Range 50 – 300 Nm
EN-48391Removal/installation spanner width: 8
Removing/installing sheathed glow plugs
KM-796-ADismantler
To open fuel system quick-release fittings
KM-807Sealing plug
Sealing fuel lines
MKM-883-1Engine Holder
Hold/lower/raise engine
MKM-883-4Hook
Holding the engine with MKM-883-1
KM-904Base Frame
Removing and installing engine with transmission
KM-955Locking Pins
Locking timing chain tensioner
KM-956Holding Wrench
KM-956-1 from the latterCounterholding the belt pulley/crankshaft
KM-2358Wire ropes
Hitching engine
KM-6001-AEngine holder
To centre engine in conjunction with KM-6173
KM-6015Sealing plug
Sealing the fuel lines
KM-6130Fixing rod
Fixing ribbed V-belt tensioner
KM-6173Engine holder
Engine bracket to front axle body in conjunction with KM-6001-A
KM-6182-1Pliers, straight
Removal/installation of compact clamps
KM-6182-2Pliers, curved
Removal/installation of compact clamps
KM-6282Remover
To remove the drive shafts from the wheel flange
KM-6327Adapter
To seal coolant expansion tank to test the coolant system for leaks, with KM-471
KM-6347Bracket
Holding the camshaft sprockets to release them
Tightening the fastening bolts in conjunction with KM-956-1
KM-6368Sealing plug
Sealing the high pressure line connections on pump, rail and injectors
KM-6372Counterhold
Counterholding when removing/installing alternator drive disc
KM-6390Centring Tool
Removing and installing front axle and aligning subframe to vehicle underbody in conjunction with KM-904 and hydraulic jack
MKM-6600-1Torque wrench 4-40 Nm
Small torque wrench with narrow range for use in restricted spaces, together with MKM-6600-100, MKM-6600-200 and MKM-6600-300
MKM-6600-2Torque wrench 20-120 Nm
Large torque wrench with wide torque range for use in restricted spaces, together with MKM-6600-100, MKM-6600-200 and MKM-6600-300
MKM-6600-100Torx bit and socket set
Sizes: E8, E10, E11, E12, E14, E16, E18, E20, E22, E24 for use in constricted spaces, together with MIM-6600-1 and MKM-6600-2
MKM-6600-200Box spanner socket set
Sizes:10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for use in constricted spaces, together with MIM-6600-1 and MKM-6600-2
MKM-6600-300Open-ended spanner socket set
Sizes:10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for use in constricted spaces, together with MIM-6600-1 and MKM-6600-2
KM-6610Holding Wrench
To counterhold the axle shaft nut. Tighten with wheel bolts on wheel hub
KM-J-37228Separation Tool
To disconnect oil pan
EN-46775Centring cover on drive side during installation
EN-46776Installing the seal ring on the engine timing side
EN-46777Installing the rear crankshaft seal ring
EN-46778Marking out tool
Flywheel to cylinder block
EN-46781Locking camshafts
Checking timing
EN-49478Adapter
Check for compression and engine pressure loss
EN-46785Marking out tool
Checking TDC
EN-46786Remover
Removing injectors in conjunction with KM-328-B
EN-47655Injector diagnostic tool
Checking the injectors on common rail diesel engines (Bosch injectors only)
EN-47656-1Pressure test plug - connection piece
Checking the charge air system for leaks in conjunction with tyre filling device
EN-47656-2Pressure test plug
Checking the charge air system for leaks in conjunction with tyre filling device
EN-48375Bonnet support
To support the bonnet in conjunction with the support frame EN-46750
CH-48375Adapter
To attach the support from EN-46750 on the vehicle

More articles — Engine and Engine Aggregates