Contents Section: Fuel Injection Systems All sections

Time Allowance Opel Calibra I

Time Allowance

Op. No.OperationTroubleTimeTime
CodesAllow.Allow.
C 20 XEC 25 XE
J 8516 00Trouble Code - Read Out - Motronic M 2.8
.2.2
TC: 99
(With TECH 1)
Add:
Trouble-shooting for test step:
01Battery voltage48, 49.1.1
09TP signal21, 22.2.2
31Sim idle switch, sim full load switch21, 22.2.2
05Intake air temperature69, 71.1.1
06Coolant temperature14, 15.1.1
07Mass air flow meter73, 74.2.2
39Knock signal16, 17, 19.2.2
40Variant code----.1.1
35Hall sensor93, 94.2.2
37Vehicle speed, odometer pulse---.2.2
25AC info switch AC compressor switch---.2.2
15PARK / NEUTRAL switch MT---.1.1
AT.1.1
14Torque control
75.1.1
41Full load prohibition, ignition/injection cutoff
79, 97.2.2
42Ignition coil cyl. 1/4----.1--
Ignition coil cyl. 2/3
----
42Ignition coil cyl. 1/4------.1
Ignition coil cyl. 2/5------
Ignition coil cyl. 3/6
------
10Engine load signal, TV load signal
----.1.1
33Fuel pump relay53, 54.2.2
34AC cutoff relay88.1.1
24Tank vent valve61, 62.1.1
43Engine speed pulse----.1.1
12Nominal idle speed, engine speed19, 31.2.2
44Nominal idle air, actual idle air
----.1.1
17IAC integrator,56,57.1.1
IAC deviation,
IAC characteristic curve correction
19O2 sensor circuit,13, 38, 39.2.2
O2 oxygen sensor
21O2 integrator,13, 38, 39.2.2
O2 idle characteristic curve,
O2 partial load characteristic curve
13Firing angle BTDC----.2.2
45Knock retardation.....2.2
11Injection pulse25, 26, 27, 28.1.1
81, 82, 83, 84
C 25 XE
also
29,32, 85, 86
46Telltale,52
excitation lead,----.1.1
injection cutoff----
control IAC pos.
----
29No trouble code display, comparison of
nominal/actual values for test steps ---- .5 .5
1 - 47 according to quick check list 4.5, F0: Data List
30No trouble code display, comparison of
nominal/actual values for test steps 1 - 8----
according to quick check list 4.7.5,

F5: Actuator Test

Ignition sparks 1 + 4----.4--
Ignition sparks 2 + 3
------
Ignition sparks 1 + 4------
Ignition sparks 2 + 5------.5
Ignition sparks 3 + 6
------
Telltale
52.1.1
IAC position
56, 57.2.2
Controlled canister purge valve
61, 62.2.2
AC cutoff relay
61, 62.1.1
47No trouble code display, comparison of
nominal/actual values for test steps 1 - 2----
according to quick check list 4.6.6, F6: ECU Reset
O2 characteristic curves
----.1.1
IAC characteristic curve
----.1.1
48No trouble code display, comparison of
nominal/actual values for test steps 1 - 3----
according to quick check list 4.6.7,

F8: ECU Control

Control engine speed
----.1.1
IAC position
56,57.1.1
Injector25, 26, 27, 28,.1.1
29, 32, 81, 82,
83, 84, 85, 86
38R + R Motronic M 2.8 control unit----.4.2
(if necessary for carrying out certain test steps)
51R + R AT control unit----.2.2
(if necessary for carrying out certain test steps)
50R + R ETC control unit----.2.1
(if necessary for carrying out certain test steps)