| Nm | |
|---|---|
| Heat shield to exhaust manifold | 8 |
| Adapter DIS ignition module to cylinder head (M8) | 20 |
| Adapter DIS ignition module to cylinder head (M10) | 30 |
| Starter to transmission (long bolt) | 60 |
| Starter to cylinder block | 45 |
| Drive disc to crankshaft | 55 + 30° + 15° 1) |
| Differential (balancer shaft unit) to crankshaft bearing cap | 20 + 45° |
| Differential (balancer shaft unit) to cylinder block | 20 + 45° |
| Exhaust manifold to cylinder head | 22 2) |
| DIS ignition module to DIS ignition module adapter (X 20 XEV) | 8 |
| Torsional vibration damper to toothed belt drive gear | 20 |
| Throttle body to intake manifold | 9 |
| Dynamic oil level control to oil pan lower part | 8 |
| Intake manifold to cylinder head | 22 2) |
| Accelerator to bulkhead (Y 22 XE) | 20 2) |
| Crankcase ventilation flange to cylinder block | 25 |
| Crankshaft pulse pick-up sensor disc to crankshaft | 13 1) |
| Transmission to cylinder block | 60 |
| Auxiliary unit(s) support to cylinder block | 35 |
| Bracket to exhaust pipe bracket | 20 |
| Starter bracket to cylinder block | 25 |
| Alternator bracket to cylinder block | 35 |
| Oil intake pipe to differential (M6) | 10 |
| Oil intake pipe bracket to differential (M8) | 20 |
| Oil intake pipe bracket to cylinder block | 6 |
| Secondary air non-return valve bracket to exhaust manifold (X 20 XEV) | 8 |
| Return roller bracket to cylinder block | 25 |
| Tank vent valve bracket to DIS ignition module adapter (X 20 XEV) | 8 |
| Compressor bracket to cylinder block and auxiliary units support | 35 |
| Rear fastening bolts to compressor bracket | 20 |
| Rear toothed belt cover to oil pump and cylinder head | 8 |
| Crankshaft pulse pick-up in cylinder block | 8 |
| Wiring trough to front toothed belt cover | 4 |
| Ribbed V-belt tension roller to ancillary component support | 25 |
| Knock sensor to cylinder block | 20 |
| Fuel line to fuel distributor pipe | 15 |
| Fuel distributor tube to intake manifold | 8 |
| Coolant flange to cylinder head | 15 |
| Coolant pump to cylinder block | 25 |
| Crankshaft bearing bridge to cylinder block | 20 + 45° |
| Crankshaft bearing cap to cylinder block | 50 + 45° + 15° 1) |
| Oxygen sensor in front exhaust pipe | 30 3) |
| Shackle to intake manifold and alternator | 20 |
| Power steering pump shackle to support | 20 |
| Exhaust gas recirculation solenoid valve to adapter, DIS ignition module | 20 |
| Ground cable to cylinder block | 20 |
| Secondary air metal pipe to exhaust manifold (X 20 XEV) | 20 4) |
| Centre tie rod to steering arm / idler | 60 |
| Engine damping block to engine bracket | 40 |
| Engine damping block to front axle body | 55 |
| Engine bracket to cylinder block | 60 |
| Engine support to transmission and cylinder block | 40 |
| Engine transport shackles to cylinder head | 20 |
| Camshaft bearing caps to cylinder head | 8 |
| Camshaft sprocket to camshaft | 50 + 60° + 15° 1) |
| Camshaft sensor to cylinder head | 6 |
| Oil drain bolt to oil pan (hex bolt) | 45 |
| Oil drain bolt to oil pan (inner Torx bolt) | 10 |
| Oil pressure switch to oil pump | 40 |
| Oil filter to oil pump | 15 |
| Oil lines to radiator | 25 |
| Oil dipstick guide tube to auxiliary units support | 25 |
| Oil pump to cylinder block | 8 |
| Oil pump cover to oil pump | 6 |
| Oil intake pipe to crankshaft bearing bridge | 20 |
| Oil intake pipe to oil pump | 8 5) |
| Oil baffle plate to crankshaft bearing bridge | 20 + 45° |
| Oil pan to oil pump and cylinder block | 8 5) |
| Upper part of oil pan to cylinder block and oil pump | 20 |
| Upper part of oil pan to transmission housing (M8) | 20 |
| Upper part of oil pan to transmission housing (M10) | 40 |
| Lower part of oil pan to upper part of oil pan | 8 + 30° 1) |
| Con-rod bearing cap to con-rod | 35 + 45° + 15° 1) |
| Power steering pump to ancillary component support | 25 |
| Hose clamps for air intake hose | 3.5 |
| Flywheel to crankshaft | 65 + 30° + 15° 1) |
| Vibration damper to front axle body bracket and to engine bracket | 40 |
| Coolant temperature sensor to DIS ignition module adapter | 10 |
| Support to intake manifold and alternator | 20 |
| Intake manifold support to intake manifold/cylinder block | 25 |
| Coolant temperature sender to DIS ignition module adapter | 11 |
| Thermostat housing to cylinder head | 15 |
| Safety valve to oil pump | 50 |
| Brake servo vacuum line to inlet manifold | 20 |
| Lower alternator fastening bolt to alternator bracket | 35 |
| Lower engine compartment cover to front axle body | 5 |
| Front fastening bolts of compressor to auxiliary units support | 35 |
| Front toothed belt cover to rear toothed belt cover | 6 |
| Front exhaust pipe to exhaust manifold | 25 |
| Toothed belt tension roller to oil pump | 20 |
| Toothed belt guide roller to guide roller bracket | 25 |
| Toothed belt guide roller to cylinder block | 25 |
| Toothed belt drive gear to crankshaft | 130 + 45° ± 5° 1) |
| Spark plug wire cover to cylinder head cover (X 20 XEV) | 3 |
| Spark plug to cylinder head | 25 |
| Ignition module to cylinder head (Y 22 XE) | 8 |
| Cylinder head to cylinder block | 25 + 90° + 90° + 90° + 15° 1) 6) |
| Cylinder head cover to cylinder head | 8 |
1
) Use new bolt(s).
2
) Use new nut(s).
3
) Insert with special grease (black).
4
) Insert bolts with mounting paste (white).
5
) Recut bolts before re-use and insert bolts with locking compound. Max. assembly time including torque check is 10 min.
6
) Retightening not required.