Recommended Torque Values
| Nm |
|---|
| Exhaust gas re-circulation valve to lower part of intake manifold | 20 |
| Axle shaft to front wheel hub | |
| Starter to cylinder block | 25 |
| Drive disc to crankshaft | 60 |
| Exhaust manifold to cylinder head | 22 |
| Bypass connection flange to cylinder head | 25 |
| DIS ignition module to DIS ignition module bracket | 8 |
| Throttle body to upper part of intake manifold (C 16 XE) | 8 |
| Throttle body to throttle body flange | 8 |
| Fuel pressure regulator to fuel distributor pipe | 8 |
Recommended Torque Values
| Nm |
|---|
| Upper part of intake manifold to lower part of intake manifold | 8 |
| Upper part of intake manifold to cylinder head cover | 8 |
| Lower part of intake manifold to cylinder head | 20 |
| Throttle body flange to lower part of intake manifold | 8 |
| Guide joint to steering knuckle | 30 |
| Coolant temperature sensor to thermostat housing | 10 |
| Alternator to alternator support | 35 |
| Alternator to alternator shackle | 20 |
| Transmission (manual and AT) to cylinder block | 60 |
| Alternator support to cylinder block | 35 |
Recommended Torque Values
| Nm |
|---|
| DIS ignition module bracket to cylinder head | 8 |
| Crankshaft pulse pickup bracket to oil pump | 10 |
| Bracket, secondary air pump filter to secondary air pump | 20 |
| Radiator bracket to air deflector panel | 10 |
| Tension strut bracket to crossmember (front member) | 50 Nm / 37 lbf. ft. + 90� + 15� |
| Bracket, secondary air pump assy. to side member | 6 |
| Rear engine bracket to engine damping block | 60 |
| Left engine bracket to transmission | 60 |
| Left engine bracket to engine damping block | 60 |
| Right engine bracket to ancillary component support | 60 |
| Right engine bracket to engine damping block | 60 |
Recommended Torque Values
| Nm |
|---|
| Rear toothed belt cover to oil pump and cylinder head | 6 |
| Hot wire mass air flow meter to upper part of air cleaner housing | 6 |
| Heat shield to exhaust manifold | 8 |
| High pressure line to power steering pump | 28 |
| Crankshaft pulse pickup to bracket | 8 |
| Increment disc to crankshaft | 95 Nm / 70 lbf. ft. + 30� + 15� |
| Ribbed V-belt tension roller to alternator support | 35 |
| Ribbed V-belt tension roller to ancillary component support | 25 |
| Knock sensor to cylinder block (M10) | 12.5 |
| Knock sensor to cylinder block (M8) | 20 |
Recommended Torque Values
| Nm |
|---|
| Secondary air combination valve to secondary air metal pipe | 6 |
| Fuel return line to fuel pressure regulator | 15 |
| Fuel distributor tube to lower part of intake manifold | 8 |
| Fuel feed line to fuel distributor pipe | 15 |
| Coolant pump to cylinder block | 8 |
| Crankshaft bearing cap to cylinder block | 50 Nm / 37 lbf. ft. + 45� + 15� |
| Oxygen sensor to exhaust manifold | 30 |
| Alternator shackle to bypass connection flange | 20 |
| Alternator shackle to lower part of intake manifold | 20 |
| Alternator plate to alternator | 20 |
Recommended Torque Values
| Nm |
|---|
| Control arm to front frame (body) | 45 Nm / 33 lbf. ft. + 45� + 15� |
| Air intake pipe with wiring harness bracket to lower part of intake manifold | 8 |
| Fan shroud to radiator | 4 |
| Fan motor to fan shroud | 4 |
| Metal pipe, secondary air to exhaust manifold (M6) | 8 |
| Metal pipe, secondary air to exhaust manifold (M8) | 20 |
| Rear engine damping block to vehicle underbody | 65 |
| Engine damping block, left, to front frame side member | 65 |
| Engine damping block, right to front frame side member | 20 |
| Engine vent pipe to cylinder block | 8 |
Recommended Torque Values
| Nm |
|---|
| Engine transport shackle to exhaust manifold | 22 |
| Engine transport shackle to cylinder head | 25 |
| Camshaft bearing caps to cylinder head | 8 |
| Camshaft pulley to camshaft | 50 Nm / 37 lbf. ft. + 60� + 15� |
| Camshaft sensor to cylinder head | 8 |
| Oil drain bolt (inner Torx bolt) to aluminium oil pan | 14 |
| Oil drain bolt (hex bolt) to aluminium oil pan | 45 |
| Oil drain bolt to sheet metal oil pan | 55 |
| Oil pressure switch to oil pump | 30 |
| Oil filter to cylinder block | 15 |
Recommended Torque Values
| Nm |
|---|
| Oil lines (AT) to cooler | 22 |
| Oil pump to cylinder block | 10 |
| Oil pump cover to oil pump | 6 |
| Oil intake pipe (bracket) to cylinder block | 8 |
| Oil intake pipe to oil pump | 8 |
| Oil pan (aluminium oil pan) to transmission housing (M10) | 40 |
| Oil pan (aluminium oil pan) to transmission housing (M8) | 20 |
| Oil pan (aluminium oil pan) to cylinder block and oil pump | 10 |
| Oil pan (sheet metal oil pan) to cylinder block and oil pump | 10 |
| Con-rod bearing cap to con-rod: | 25 Nm /18 lbf. ft. + 30� |
Recommended Torque Values
| Nm |
|---|
| Power steering pump to ancillary component support | 20 |
| Wheel to wheel hub | 110 |
| Flywheel to crankshaft | 35 Nm / 26 lbf. ft. + 30� + 15� |
| Flywheel cover plate to transmission. | 7 |
| Coolant temperature sensor to thermostat housing | 14 |
| Metal pipe support, secondary air to exhaust manifold | 8 |
| Metal pipe support, secondary air to metal pipe, secondary air | 8 |
| Temperature switch to radiator | 20 |
| Thermostat (thermostat housing cover) to thermostat housing | 8 |
| Thermostat housing to cylinder head | 20 |
Recommended Torque Values
| Nm |
|---|
| Brake servo vacuum line to upper part of intake manifold | 18 |
| Compressor to ancillary component support | 35 |
| Compressor to bracket | 35 |
| Safety valve closure bolt to oil pump | 50 |
| Front exhaust pipe to exhaust manifold | 20 |
| Front exhaust pipe to catalytic converter flange | 18 |
| Toothed belt cover - lower part to rear toothed belt cover | 4 |
| Toothed belt cover - upper part to rear toothed belt cover | 4 |
| Toothed belt tension roller to oil pump | 20 |
| Toothed belt guide roller on exhaust side to cylinder block | 25 |
Recommended Torque Values
| Nm |
|---|
| Toothed belt guide roller on intake side to cylinder block | 25 |
| Ignition cable cover to upper part of intake manifold | 8 |
| Spark plugs in cylinder head | 25 |
| Secondary air pump assy. to bracket | 20 |
| Cylinder head to cylinder block | 25 Nm / 18 lbf. ft. + 90� + 90� + 90� + 45� |
| Cylinder head cover to cylinder block | 8 |
