Note. Never interchange used bearing shells. Bearing shells that are worn through the nickel coating must be replaced
Contents
Wiring diagrams Section: Mechanical- Engine Identification
- Engine Specifications
- Engine, Removing and Installing
- Removing
- Vehicles with Automatic Transmission
- Vehicles Without Drain Plug
- Vehicles Up to 06.03
- Vehicles as of 07.03
- Vehicles with Automatic Transmission 01V
- Installing
- Vehicles with Sac Clutch Pressure Plate
- Engine/transmission (bellhousing) Bolt Tightening Torques
- Tightening Torque
- Special Tools and Equipment
- Procedure
- Lock Carrier in Service Position, Overview
- Ribbed Belt for Vane Pump, Generator and A/c System
- Vibration Damper, Removing and Installing
- Toothed Belt Cover, Removing and Installing
- Toothed Belt Drive, Assembly Overview
- Installing (adjusting Valve Timing)
- Sealing Flanges and Flywheel/drive Plate, Removing and Installing
- Required Equipment
- Automatic Transmission (cvt) 01J
- Crankshaft, Removing and Installing
- Application of Crankshaft Bearing Shells for Cylinder Block
- Crankshaft Measurements
- Radial Clearance
- Pistons and Connecting Rods, Disassembling and Assembling
- Checking Piston Ring Side Clearance
- Checking Pistons
- Checking Cylinder Bore
- Piston Installed Position and Application Piston/cylinder
- Marking Connecting Rods
- Oil Injector Jet for Piston Cooling
- Piston and Cylinder Measurements
- Test Sequence
- Cylinder Head, Removing and Installing
- Part I
- Part Ii
- Check Cylinder Head for Warpage
- Cylinder Head Refacing Dimension
- Sealing Cap (core Plug) in Cylinder Head, Driving In
- Tightening Torques
- Cylinder Head, Installing
- Test Requirements
- Valve Train, Servicing
- Valve Dimensions
- Valves, Checking
- Valve Seats, Refacing
- Determining Maximum Allowable Refacing Dimension
- Camshaft Adjustment, Checking
- Test Requirement
- Camshaft Adjustment (exhaust), Checking
- Camshaft Adjustment (intake), Checking
- Valves for Camshaft Adjustment (intake), Activating
- Valves for Camshaft Adjustment (exhaust), Activating
- Electrical Test of Solenoid Valve for Camshaft Adjustment
- Valve for Camshaft Adjustment (exhaust)
- Lubrication System Components, Removing and Installing
- Part I - Oil Pan (lower Part), Oil Pump
- Part Ii - Oil Pan (upper Part), Oil Filter
- Oil Check Valves and Spray Jet Valve, Overview
- Black Oil Pressure Switch
- Viscosity Classes and Oil Specifications
- A/c Compressor
- Abbreviations
- Accessories Control Systems
- Airbag
- Anti-Lock/traction Control
- Application
- Automatic HVAC System
- Automatic Trans
- Axle Shafts
- Basic Trouble Shooting
- Blowers, Superchargers & Turbochargers
- Brakes
- Cabin Air Filter
- Charging System
- Check Lists
- Clutches Manual & Hydraulic
- Communication Devices
- Computer Relearn
- Cooling Fan
- Cruise Control Systems
- Diagnostic Connector Locations
- Differentials & Drive Axles
- Door Locks & Anti-Theft Systems
- Drive Cycles
- Driveline/axles
- Driveshaft & Universal Joints
- DTC Index
- Electrical
- Electrical Component Locations
- Emission Applications
- Engine
- Engine Performance
- Entertainment Systems
- Exhaust
- Exterior Body Panels
- Fuel System
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- Identification
- Ignition System
- Manual Trans
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Metric Conversions
- Mirrors
- Mode 6
- Navigation System
- Oem General Information
- Procedures
- Reset Procedures
- Restraints
- Seats
- Specifications
- Starter
- Steering
- Steering Column Switches
- Sun Roof/t-Top/convertible Top
- Suspension Front
- Suspension Rear
- Testing & Diagnostics
- Timing Belt
- Traction Control Disable
- Transmission
- Wheel & Tire System
- Wheel Alignment
- Wiper/washer Systems