Home/Audi/A4/Audi A4 B6 (2000-2006)/Repair manual/Multiport Fuel Injection (mfi) - 3.0l Avk
Manual sections Wiring diagrams
Repair manual

Multiport Fuel Injection (mfi) - 3.0l Avk Audi A4 B6

Step-by-step instructions on "Multiport Fuel Injection (mfi) - 3.0l Avk" for Audi A4 B6 (2000–2006). Pick an article — removal, installation, adjustment and diagnostics with illustrations.

91subsections
91articles
106illustrations

Safety precautions

1 article

Rules for cleanliness

1 article

Technical data

1 article

Component locations, overview

1 article

Location of Throttle Position (TP) sensor -G79- and Sender 2 for accelerator pedal position -G185

1 article

Removing and installing gas pedal module

1 article

Location of Fuel Pump (FP) relay -J17

1 article

Location Brake light switch -F- and Brake pedal switch (cruise control/diesel direct fuel injection -F47-, Clutch vacuum vent valve switch -F36

1 article

Removing and installing switches

1 article

Locations in electronics box (plenum chamber)

1 article

Identification of connector bracket - right side of vehicle

1 article

Identification of connector bracket - left side of vehicle

1 article

Location of Intake manifold change-over valve -N156

1 article

Air cleaner, disassembling and assembling

1 article

Intake manifold change-over system components, removing and installing

1 article

Wiring and component check with test box VAG 1598/31

1 article

Procedure following interruption of voltage supply

1 article

The following steps need to be performed after reconnecting the power supply

1 article

Engine Control Module (ECM) (without metal anti-theft housing), replacing

1 article

Removing

1 article

Installing

1 article

The following steps need to be performed after connecting the new engine control module

1 article

Engine Control Module (ECM) (with metal anti-theft housing), replacing

1 article

The following equipment is required

1 article

Procedure

1 article

Installing Engine Control Module (ECM)

1 article

After connecting a new Engine Control Module (ECM), the following work steps must be performed

1 article

Special tools and equipment

1 article

Test requirements

1 article

Test sequence

1 article

If the idling speed is too high or too low and there are no DTCs recorded in the DTC memory, perform the following tests marked with a dot

1 article

Significance of 5-digit readout of display group 056

1 article

Fuel pressure regulator and holding pressure (vehicles up to 06.03), checking

1 article

Checking system pressure

1 article

Testing holding pressure

1 article

System pressure and holding pressure (vehicles as of 07.03), checking

1 article

Checking holding pressure

1 article

Checking fuel pressure regulator - vehicles with Front Wheel Drive (FWD)

1 article

Checking fuel pressure regulator - vehicles with All Wheel Drive (AWD)

1 article

Both cylinder banks, continued

1 article

Fuel rail with injectors, disassembling and assembling

1 article

Loosening and tightening union nut for fuel supply line in vehicles as of 07.03

1 article

Vehicles up to 06.03

1 article

All

1 article

Vehicles as of 07.03

1 article

Tightening torque

1 article

Testing for leaks

1 article

Checking injection quantity

1 article

Fuel Pump (FP) relay -J17- and activation, checking

1 article

Functional check of fuel pump relay

1 article

Checking activation of fuel pump relay

1 article

Checking voltage supply of fuel pump and components

1 article

Mass Air Flow (MAF) sensor -G70-, checking

1 article

Checking function

1 article

All models

1 article

Evaluation of display group 002

1 article

Checking wiring to mass air flow (MAF) sensor

1 article

Intake manifold change-over, checking

1 article

Intake manifold change-over, checking function

1 article

Checking internal resistance

1 article

Checking actuation

1 article

Checking oxygen sensor learned values and oxygen sensor control

1 article

Evaluating display group 032

1 article

Evaluating display group 033

1 article

Test conditions

1 article

Check voltage supply for oxygen sensor heating

1 article

Oxygen sensors and oxygen sensor control behind catalytic converter, checking

1 article

Checking oxygen sensor control behind catalytic converter

1 article

Evaluation of display groups 037 and 038

1 article

Checking basic voltage

1 article

Removing left oxygen sensor behind catalytic converter

1 article

Vehicles with automatic transmission

1 article

Function of the electronic throttle system

1 article

Malfunction lamp for electronic throttle in instrument cluster

1 article

Functional check on EPC warning lamp

1 article

Throttle valve control module -J338-, checking

1 article

Throttle valve control module -J338-, adaptation

1 article

Requirements

1 article

Angle sensor for throttle valve actuator, checking

1 article

Checking the voltage supply to the throttle valve control module

1 article

Checking wiring

1 article

Kickdown function, adapting

1 article

Preconditions

1 article

Check switch

1 article

Vehicles with multitronic 01J

1 article

Wiring for crash signal, checking

1 article

Data exchange between engine control module and other CAN-control modules, checking

1 article

Testing the bus system

1 article

Checking a "two-wire bus system"

1 article

VACUUM HOSE DIAGRAM(S)

1 article