Home ReviewsRefund
Home/Opel/Agila/Opel Agila B (2008-2011)/Repair manual/Engine Mechanics - K10B/Special Tools
Contents Wiring diagrams Section: Engine Mechanics - K10B All sections

Special Tools Opel Agila B

Engine Mechanics - K10B 41 illustrations
CH-48373Fixture, engine/transmission/front axle body
For removing and installing front axle body with engine and transmission assembly (in conjunction with KM-904 and hydraulic jack). For supporting engine from beneath with engine mount removed
CH-48373-100Frame mounts and supports
For removing and installing front axle body with engine and transmission assembly (in conjunction with CH-48373)
EN-46779Installer
To install valve stem oil seals
EN-47649Engine Bridge
To support engine and transmission assembly
EN-47649-100Engine Bridge Feet
For use with EN-47649
EN-47650Carrier Frame
For use with EN-47649
EN-47650-200Rear Adapter Support
For use with EN-47650
EN-49042Seal Installer
To install front oil seal to timing chain cover
EN-49110Lifting Eye
For use with KM-2358
EN-49118Compression Test Adapter
To check engine compression or engine pressure loss
EN-49119Compression Test Adapter
Used with EN-49118
EN-49142Seal Installer
To install crankshaft rear oil seal
EN-49143Seal Guide
Guide for crankshaft rear oil seal
EN-49148Camshaft Sprocket Guide
Guide for camshaft sprocket
EN-49150Pad
For use with KM-161-B
KM-113-2Mount for Assembly Device
Used with KM-6215 Assembly Device
KM-161-BPuller
For removing crankshaft pulley
KM-194Spark Plug Wrench
For removing spark plug
KM-210-3Puller
To remove crankshaft pulley
KM-470-BAngular Torque Wrench
To tighten bolts according to angle
KM-427Drift
To install dowel pins
KM-498-BFluid Pressure Gauge
To check engine oil pressure
KM-498-50Adapter
Used with KM-498-B to check engine oil pressure
KM-507-CRemover
To release tie rod end from steering knuckle
KM-648Oil Filter Wrench
To remove and install oil filter
KM-652Flywheel Locking Tool
To lock flywheel when removing and installing clutch or flywheel
KM-807Sealing Plugs
To seal fuel lines
KM-835-AInstaller (6 mm)
To install valve stem seals
KM-840Remover
To remove valve stem seal
KM-849Storage Facility
Storage facility for pistons, con-rods, valves etc.
KM-904Base Frame
For removing and installing front axle body with engine and transmission assembly (in conjunction with CH-48373 and hydraulic jack)
KM-956-1Handle
Handle for Holding Wrench KM-6610 and Holder KM-6347
KM-2358Wire Rope
To support engine
KM-6047Holder
To counterhold crankshaft pulley when releasing bolt
KM-6091Installer (6 mm)
To install the valve stem seal
KM-6167Adapter Set
Assembly device for operations on cylinder head
KM-6171Release tool
To release valve
KM-6179Socket
To remove and install oxygen sensor
KM-6215Assembly Device
Assembly device for operations on cylinder head
KM-6282Remover
To release axle shaft from wheel hub
KM-6347Holder
To counterhold crankshaft pulley when releasing bolt
KM-6610Holding Wrench
To counterhold axle shaft. Fasten to wheel hub with wheel bolts
KM-J-37228Seal Breaker
For cutting through sealant to separate components
MKM-667Vacuum Gauge Tool
For checking engine vacuum
MKM-6086To install/remove valve collets (6 mm)
To remove and install valve springs and valve cotters
MKM-6600-2Torque Spanner (20 - 120 Nm)
Large torque spanner with high torque range, for use in tight spaces, in conjunction with MKM-6600-300
MKM-6600-300Open Ended Spanner Set
Size: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for use in confined spaces in conjunction with MKM-6600-2

More articles — Engine