Recommended Torque Values
| Nm |
|---|
| Flywheel cover to transmission | 7 |
| Exhaust gas recirculation valve to intake manifold | 20 |
| Starter to cylinder block | 25 |
| Exhaust manifold to cylinder head | 22 |
| Exhaust pipe to exhaust manifold | 25 |
| DIS ignition module to DIS ignition module support plate | 8 |
| Throttle valve injection housing to intake manifold (Multec) | 22 |
| Throttle valve injection housing, upper part, to throttle valve injection housing (Multec) | 6 |
| Throttle valve potentiometer to throttle valve injection housing (Multec) | 2 |
| Throttle valve potentiometer to throttle body (Multec-M) | 3 |
| Throttle body to intake manifold (Multec-M) | 9 |
| Pressure plate to camshaft housing | 8 |
Recommended Torque Values
| Nm |
|---|
| Through bolts to alternator | 4 - 6 |
| Through bolts to compact alternator (Delco-Remy) | 9.5 |
| Intake manifold to cylinder head | 22 |
| Guide joint to steering knuckle | 30 |
| Alternator to alternator bracket (M10) | 40 |
| Alternator to alternator bracket (M8) | 30 |
| Transmission to cylinder block | 60 |
| Injector bracket to throttle valve injection housing (Multec) | 3 |
| Alternator bracket to cylinder block (ribbed V-belt) | 35 |
| Alternator bracket to cylinder block | 40 |
| Inductive pulse pick-up bracket to oil pump housing | 10 |
| Refrigerant line bracket to exhaust manifold | 22 |
Recommended Torque Values
| Nm |
|---|
| Radiator bracket to air deflector panel | 6 |
| Oil intake pipe bracket to cylinder block | 8 |
| Power steering pump/compressor bracket to cylinder block | 40 |
| Tension strut bracket to crossmember (front member) | 50 + 90� + 15� |
| Rear toothed belt cover to oil pump and camshaft housing | 6 |
| Rear toothed belt cover to camshaft housing | 6 |
| High pressure line to power steering pump | 28 |
| Hydraulic hose to radiator | 22 |
| Inductive pulse pick-up to bracket, inductive pulse pick-up | 8 |
| Knock sensor to cylinder block (M10) | 12.5 |
| Knock sensor to cylinder block (M8) | 20 |
| Fuel pressure regulator to throttle valve injection housing (Multec) | 3 |
Recommended Torque Values
| Nm |
|---|
| Fuel pressure regulator to fuel rail (Multec-M) | 8 |
| Fuel connection to throttle valve injection housing (Multec) | 30 |
| Fuel rail to intake manifold (Multec-M) | 9 |
| Coolant compensation tank to bulkhead | 2 |
| Coolant pump to cylinder block | 8 |
| Coolant pipe to cylinder block | 20 |
| Coolant pipe to transmission | 60 |
| Coolant thermostat housing to cylinder head | 10 |
| Crankshaft bearing cap to cylinder block | 50 + 45� + 15� |
| Crankshaft pulley/increment disc with toothed belt drive pulley to crankshaft (M 12) | 95 + 30� + 15� |
| Oxygen sensor to exhaust manifold | 30 |
| Alternator plate to intake manifold | 20 |
Recommended Torque Values
| Nm |
|---|
| Alternator plate to alternator | 20 |
| Idle speed stepper motor to throttle valve injection housing (Multec) | 3 |
| Idle speed stepper motor to throttle body | 3 |
| Front suspension control arm to body | 45 + 45� + 15� |
| Fan motor to fan shroud | 4 |
| Fan shroud to radiator | 4 |
| Air cleaner cover to throttle valve injection housing | 4 |
| Rear engine damping block to vehicle underbody | 65 |
| Front left engine damping block to front frame side member | 65 |
| Front right engine damping block to front frame side member (vehicles with power steering and air conditioning) | 20 |
| Front right engine damping block to front frame side member (vehicles without power steering and air conditioning) | 65 |
| Rear engine bracket to transmission | 70 |
Recommended Torque Values
| Nm |
|---|
| Rear engine bracket to engine damping block | 60 |
| Left engine bracket to transmission | 60 |
| Left engine bracket to engine damping block | 60 |
| Right engine bracket to bracket for power steering / compressor pump | 60 |
| Right engine bracket to engine damping block | 60 |
| Right engine bracket to cylinder block | 60 |
| Pulley nut on armature shaft (Bosch) | 40 � 5 |
| Pulley nut on armature shaft (Delco-Remy) | 80 |
| Pulley nut on armature shaft (Bosch compact alternator) | 65 � 5 |
| Engine bracket nut to engine damping block | 60 |
| Camshaft housing cover to camshaft housing | 8 |
| Camshaft pulley to camshaft | 45 |
Recommended Torque Values
| Nm |
|---|
| Upper toothed belt cover to rear toothed belt cover | 4 |
| Oil drain plug to oil pan (sheet metal oil pan) | 55 |
| Oil drain bolt (hex bolt) to aluminium oil pan | 45 |
| Oil drain bolt (inner Torx bolt) to aluminium oil pan | 14 |
| Oil pressure switch to oil pump | 30 |
| Oil pump to cylinder block | 10 |
| Oil pump cover to oil pump | 6 |
| Oil intake pipe to oil pump | 8 |
| Oil pan to transmission casing (aluminium oil pan) M8 | 20 |
| Oil pan to transmission casing (aluminium oil pan) M10 | 40 |
| Oil pan to cylinder block | 10 |
| Con-rod bearing cap to con-rod (bolt thread length 40 mm) | 25 + 30� |
Recommended Torque Values
| Nm |
|---|
| Con-rod bearing cap to con-rod (bolt thread length 15 mm) | 25 |
| Power steering pump to bracket for power steering pump/compressor | 20 |
| Wheel to wheel hub | 110 |
| Engine bracket bolt to engine damping block | 60 |
| Flywheel to crankshaft | 35 + 30� + 15� |
| Alternator shackle to intake manifold | 25 |
| Alternator shackle to alternator | 25 |
| Ribbed V-belt tension roller to bracket for power steering pump/compressor | 25 |
| Ribbed V-belt tension roller to cylinder block | 20 |
| Toothed belt tension roller to oil pump housing | 20 |
| Alternator support to alternator/intake manifold | 20 |
| Coolant temperature sensor (temperature gauge) in intake manifold | 10 |
| Coolant temperature sensor (Multec) to intake manifold | 20 |
Recommended Torque Values
| Nm |
|---|
| Coolant temperature sensor (Multec-M) in cylinder head | 20 |
| Temperature switch to radiator | 20 |
| DIS ignition module support plate to camshaft housing | 12 |
| Vacuum connection flange to throttle valve injection housing (Multec) | 3 |
| Lower toothed belt cover to rear toothed belt cover | 4 |
| Controlled canister purge valve to camshaft housing | 10 |
| Safety valve closure bolt to oil pump | 50 |
| Front exhaust pipe to catalytic converter connection flange | 18 |
| Front exhaust pipe to exhaust manifold | 25 |
| Pre-heater scoop to exhaust manifold | 8 |
| Spark plug to cylinder head | 25 |
| Cylinder head and camshaft housing to cylinder block | 25 + 60� + 60� + 60� |
