Special Service Tools
| KM-128-A | Test unit |
|---|
| Test V-belt tension |
| KM-135 | Adapter |
| Measure engine oil pressure in conjunction with KM-498-B |
| KM-263-B | Engine bridge |
| Holding the engine |
| KM-328-B | Remover |
| Removing the crankshaft needle bearing in conjunction with KM-469-A |
| KM-340-G | Valve seat milling set |
| Milling, correcting valve seat |
| KM-348 | Spring tensioner |
| Compressing valve springs, cylinder head dismantled |
Special Service Tools (Continued)
| KM-352 | Insertion sleeve |
|---|
| Assembly of valve stem seals |
| KM-412 | Engine assembly stand |
| Holding dismantled engine |
| KM-412-3 | Adapter |
| Holding engine in conjunction with KM-412 |
| KM-417 | Assembly sleeves |
| Inserting crankshaft sealing ring into oil pump housing |
| KM-419 | Distance gauge |
| Checking valve projection after machining valve seat |
| KM-421-A | Adjusting spanner |
| Adjusting toothed belt tension |
Special Service Tools (Continued)
| KM-422 | Installer |
|---|
| Inserting sealing ring into camshaft |
| KM-427 | Remover and installer |
| Hammering the centring punches into the cylinder block |
| KM-460-B | Removers |
| Pushing the axle shaft out of the transmission |
| KM-470-B | Angled tightening wrench |
| Tightening cylinder head bolts |
| KM-471 | Adapter |
| Testing cooling system under pressure in conjunction with cooling system tester |
| KM-498-B | Oil pressure gauge |
| Checking engine oil pressure in conjunction with KM-135 |
Special Service Tools (Continued)
| KM-517-B | Flywheel holder |
|---|
| Locking flywheel with the transmission installed |
| KM-526-A | Clamping bracket |
| Clutch assembly with 3 clamps |
| KM-565-A | Remover, installer |
| Removing and installing cam followers and hydraulic valve lifters |
| MKM-588-A | Pressure gauge for performing checks |
| Checking fuel pressure |
| MKM-596-A | Measuring instrument |
| Measuring oil temperature |
| MKM-604-D | Torx bit and socket set |
| Removing and installing Torx bolts |
Special Service Tools (Continued)
| KM-609 | Electronics kit I |
|---|
| Diagnosis of electrical and electronic systems |
| MKM-610 | Torque wrench 1/2" drive |
| Range 30-130 Nm |
| MKM-611 | Torque wrench 3/8" drive |
| Range 10-60 Nm |
| KM-632-A | Remover, installer |
| Tensioning clutch assembly, engine removed |
| KM-634 | Remover, installer |
| Removing and installing piston bolts |
| KM-640 | Diagnostic switch |
| Triggering release of flashing code, engines with self-diagnosis |
Special Service Tools (Continued)
| KM-652 | Flywheel holder |
|---|
| Locking flywheel |
| KM-658 | Installer |
| Installing rear crankshaft sealing ring |
| KM-664 | Reamer set 7 mm |
| Roughening the valve guide |
| MKM-667 | Pressure and vacuum pump |
| Checking the vacuum unit for leaks |
| MKM-669 | Torque wrench 1/2" drive |
| Range 50-300 Nm |
| KM-717 | Puller |
| Pulling out spark plug boot |
Special Service Tools (Continued)
| KM-726-A | Oil filter wrench |
|---|
| Removing and installing the oil filter |
| KM-728-A | Wrench for removing and installing |
| Removing and installing the knock sensor on X 12 SZ and X 14 SZ |
| KM-734 | Guide pin |
| Centring the clutch disc |
| KM-834-A | Remover, installer |
| Removing and installing heat protection sleeves |
| MKM-874 | Precision multi-timer |
| Checking electrical/electronic components |
| MKM-883-1 | Engine bridge |
| Holding the engine |
Special Service Tools (Continued)
| KM-902 | Remover |
|---|
| Removing the axle shafts |
| KM-904 | Base frame |
| Removing and installing various vehicle components |
| KM-911 | Flywheel holder |
| Locking flywheel/drive disc |
| KM-937 | Extension |
| Removing drive shaft with KM-460-B |
| KM-956-1 | Clamp with handle |
| Holding the camshaft pulleys to release/tighten the fastening bolts in conjunction with KM-6347 |
| KM-2358 | Engine-lifting straps |
| Removing and installing the engine |
Special Service Tools (Continued)
| KM-6054 | Holding the engine |
|---|
| Removing and installing the engine |
| KM-6347 | Bracket |
| Holding the camshaft pulleys to release/tighten the fastening bolts in conjunction with KM-956-1 |
| KM-J-26792 | Test spark plug |
| Testing ignition sparks |
| KM-J-34730-91 | Pressure testing unit |
| Checking the fuel pressure (Multec-M) |
| KM-J-37228 | Separating tool |
| For removing the sheet metal oil pan |
