General Description
PCM/TCM decide that error is detected, when checksum is wrong by PCM/TCM internal operation.
PCM/TCM watch that PCM/TCM checks error of each data by each data checksum for PCM/TCM internal operation value.
DTC Description
This code is set when PCM/TCM detected checksum error by internal operation.
(Checksum error is detected when PCM/TCM's ROM or DATA is changed by reprogram illegally.)
Shift lever positions P-range (Parking), R-range (Reverse), N-range (Neutral) and D-range (Driving) are changed by driver need and lever position is sent to PCM/TCM to control a gear ration.
This code is set when undefined code is input to PCM/TCM without specific of transmission pattern table. (See below)
Shift lever positions P-range (Parking), R-range (Reverse), N-range (Neutral) and D-range (Driving) are changed by driver need and lever position is sent to PCM/TCM to control a gear ration.
This code is set when undefined range signal is input to PCM/TCM without specific of transmission pattern table. (See below)
Transmission oil temperature sensor is installed at valve body. This sensor is used thermistor which is changed by temperature variation. If PCM/TCM supplied about 5 voltage to sensor, then sensor output value is changed by ATF temperature variation. Transmission oil temperature sensor is very important for Transmission and sensor value is input to PCM/TCM and That information (sensor value) is important used for Damper clutch, Detected Non performance area, Controlled oil temperature variation and oil pressure at change of speed and other use.
This code is set when oil temperature sensor value is input lower specification to PCM/TCM.
Transmission oil temperature sensor is installed at valve body. This sensor is used thermistor which is changed by temperature variation. If PCM/TCM supplied about 5 voltage to sensor, then sensor output value is changed by ATF temperature variation. Transmission oil temperature sensor is very important for Transmission and sensor value is input to PCM/TCM and That information (sensor value) is important used for Damper clutch, Detected Non performance area, Controlled oil temperature variation and oil pressure at change of speed and other use.
This code is set when oil temperature sensor value is input higher specification to PCM/TCM.
Input/output speed sensor is one body and installed in transmission. It's used hall sensor of an electric current type, and current is changed by magnetic variation. Each sensors are composite 2 pins and PCM/TCM supplied power to sensor and controlled by PCM/TCM.
This code is set when vehicle speed is above 20 km/h but input speed signal is not detected by Input speed sensor.
Input speed sensor value must be equal Output speed sensor value times each gear ratio at each gear position of transmission. That operation value equal with TCM operation value. For example Output speed sensor value is 1000 RPM and 6th speed gear ratio is 0.8 then Input speed sensor value must be 800 RPM.
This code is set when Input speed sensor value is different with TCM operation value, caused by control valve sticking, solenoid valve fault (most of fault is mechanical, rarely electrical fault).
Input/output speed sensor is one body and installed in transmission. It's used hall sensor of an electric current type, and current is changed by magnetic variation. Each sensors are composite 2 pins and PCM/TCM supplied power to sensor and controlled by PCM/TCM.
This code is set when vehicle speed is above 20 km/h but output speed signal is not detected by Output speed sensor.
Input speed sensor value must be equal Output speed sensor value times each gear ratio at each gear position of transmission. That operation value equal with TCM operation value. For example Output speed sensor value is 1000 RPM and 3rd speed gear ratio is 1.8 then Input speed sensor value must be 1800 RPM.
This code is set when Input speed sensor value is different with TCM operation value, caused by control valve sticking, solenoid valve fault (most of fault is mechanical, rarely electrical fault).
Input speed sensor value must be equal Output speed sensor value times each gear ratio at each gear position of transmission. That operation value equal with TCM operation value. For example Output speed sensor value is 1000 RPM and 4th speed gear ratio is 1.4 then Input speed sensor value must be 1400 RPM.
This code is set when Input speed sensor value is different with TCM operation value, caused by control valve sticking, solenoid valve fault (most of fault is mechanical, rarely electrical fault).
Input speed sensor value must be equal Output speed sensor value times each gear ratio at each gear position of transmission. That operation value equal with TCM operation value. For example Output speed sensor value is 1000 RPM and 5th speed gear ratio is 1.0 then Input speed sensor value must be 1000 RPM.
This code is set when Input speed sensor value is different with TCM operation value, caused by control valve sticking, solenoid valve fault (most of fault is mechanical, rarely electrical fault).
Input speed sensor value must be equal Output speed sensor value times each gear ratio at each gear position of transmission. That operation value equal with TCM operation value. For example Output speed sensor value is 1000 RPM and 1st speed gear ratio is 4.7 then Input speed sensor value must be 4700 RPM.
This code is set when Input speed sensor value is different with TCM operation value, caused by control valve sticking, solenoid valve fault (most of fault is mechanical, rarely electrical fault).
Input speed sensor value must be equal Output speed sensor value times each gear ratio at each gear position of transmission. That operation value equal with TCM operation value. For example Output speed sensor value is 1000 RPM and 2nd speed gear ratio is 2.8 then Input speed sensor value must be 2800 RPM.
This code is set when Input speed sensor value is different with TCM operation value, caused by control valve sticking, solenoid valve fault (most of fault is mechanical, rarely electrical fault).
PCM/TCM control Damper clutch performance by supplied oil pressure.
Damper clutch is for fuel reduction by decreasing oil pressure component's resistance in T/C.
This code is set when Damper clutch is opened & sticked.
PCM/TCM control Damper clutch performance by supplied oil pressure.
Damper clutch is for fuel reduction by decreasing oil pressure component's resistance in T/C.
This code is set when circuit open or short detected by PCM/TCM.
PCM/TCM control Pressure control solenoid valve by changed current for reducing shift shock.
This code is set when circuit open or short detected by PCM/TCM.
PCM/TCM control UD-VFS (Shift Control Solenoid Valve) solenoid valve by changed current for reducing UD brake shock.
This code is set when circuit open or short detected by PCM/TCM.
PCM/TCM control 26/B-VFS solenoid valve by changed current for reducing 26 brake shock. And PCM/TCM charge pressure for reducing shift shock at 1st speed to 2nd speed by pre-Fill control.
This code is set when circuit open or short detected by PCM/TCM.
PCM/TCM control 35R/C-VFS solenoid valve by changed current for reducing 35R clutch shock.
This code is set when circuit open or short detected by PCM/TCM.
PCM/TCM control OD-VFS solenoid valve by changed current for reducing OD clutch shock.
This code is set when circuit open or short detected by PCM/TCM.
Shift solenoid valve is ON/OFF type and changed a way of oil direction. PCM/TCM control solenoid valve to set gear speed position.
This code is set when circuit open or short detected by PCM/TCM.
PCM (TCM) monitored supplied voltage to ATM solenoid valve. This voltage is without specific, then gear is fixed 4th speed.
This code is set when input voltage of solenoid is without specification.
Applied manual transaxle function at Auto transaxle. It's used for sudden acceleration or engine brake.
This code is set when circuit open or short detected at Sports mode switch by PCM/TCM.
Shift solenoid valve is ON/OFF type and changed a way of oil direction. PCM/TCM control solenoid valve to set gear speed position.
This code is set when circuit open or short detected by PCM/TCM.
Vehicle electronic control need many informations of each module to reduce exhaust and increase convenience/safety by optimum control. The TCM can either receive data from the Engine Control Module or ABS control module, or it can send data to the ECM and ABSECM by using CAN communication. The CAN communication is one of the vehicle communications method, which is now widely used to transfer the vehicle data.
This code is set when PCM/TCM detected that wrong message is sent or No reception of communication line.
Vehicle electronic control need many informations of each module to reduce exhaust and increase convenience/safety by optimum control. The TCM can either receive data from the Engine Control Module or ABS control module, or it can send data to the ECM and ABSECM by using CAN communication. The CAN communication is one of the vehicle communications method, which is now widely used to transfer the vehicle data.
This code is set when PCM/TCM detected that message is not received at communication line.