- Oil pump drive components are located behind front engine cover. Drain engine coolant. See «DRAINING COOLING SYSTEM»(ref-147486-S06159856372002091600000).
- Remove oil pan. See «OIL PAN»(ref-147486-S10326072892002091600000) under REMOVAL & INSTALLATION.
- Remove timing belt. See «TIMING BELT»(ref-147486-S11057228442002091600000) under REMOVAL & INSTALLATION.
- Remove idler pulley. Remove crankshaft gear. Remove oil spray jet valve from front cover. Remove timing belt tensioner. (Схема №88)and (Схема №89).
- Remove lever for timing belt tensioner. Remove oil pump. To install, reverse removal procedure. Ensure drive cog on oil pump engages crankshaft. Replace oil seal. See «CRANKSHAFT FRONT OIL SEAL»(ref-147486-S17607505182002091600000) under REMOVAL & INSTALLATION.
- Tighten components to specification. See «TORQUE SPECIFICATIONS»(ref-147486-S30794586192002091600000).
- Refill and bleed air from cooling system. See «COOLING SYSTEM BLEEDING»(ref-147486-S31613995762002091600000) under REMOVAL & INSTALLATION.
Contents
Wiring diagrams Section: Mechanical- Engine Identification
- Accelerator Pedal
- Valve Clearance Adjustment
- Trouble Shooting
- Removal & Installation
- Fuel Pressure Release
- Draining Cooling System
- Cooling System Bleeding
- Remove
- Lock Carrier
- Placing in Service Position (A4 & A6)
- Removal & Installation (A4)
- Removal (A6)
- Installation (A6)
- Intake Manifold
- Removal & Installation (audi)
- Cylinder Head
- Core Plug (cylinder Head)
- Crankshaft Front Oil Seal
- Ptfe Seal Installation Precautions
- Timing Belt
- Camshafts
- Valve Lifters
- Camshaft Oil Seals
- Installation (left Side Camshaft)
- Drive Plate (a/t)
- Bearing Bushing for Torque Converter
- Crankshaft Rear Oil Seal
- Thermostat
- Water Pump
- Oil pan(a4 & a6)
- Removal (lower Pan- A4 & A6)
- Installation (lower Oil Pan- A4 & A6)
- Installation (upper Oil Pan- A4 & A6)
- Overhaul
- Camshaft Axial Play
- Valves
- Valve Guides Checking
- Valve Guide Removal
- Valve Guide Installing
- Valve Seat
- Valves Stem Seals Installing (head Installed)
- Cylinder Block Assembly
- Fitting Pistons
- Connecting Rod Bearings
- Thrust Bearing
- Cylinder Block
- Crankcase Capacity
- Oil Pressure
- Oil Viscosity & Type
- Oil Pump
- Removal & Installation (cog Driven)
- Removal & Installation (chain Driven)
- Checking Procedure
- Oil Check Valve Replacement
- Torque Specifications
- General Specifications
- Crankshaft, Main Bearings & Connecting Rod Bearings Specifications
- Pistons, Piston Pins & Piston Rings Specifications
- Cylinder Block Specifications
- Engine Valves & Valve Guides Specifications
- Cylinder Head Specifications
- Camshaft Specifications
- Abbreviations
- Airbag
- Anti-Lock/traction Control
- Application
- Automatic HVAC System
- Automatic Trans
- Axle Shafts
- Basic Trouble Shooting
- Brakes
- Cabin Air Filter
- Charging System
- Check Lists
- Clutches Manual & Hydraulic
- Communication Devices
- Computer Relearn
- Cooling System (mechanical)
- Cruise Control Systems
- Diagnostic Connector Locations
- Differentials & Drive Axles
- Door Locks & Anti-Theft Systems
- Drive Cycles
- Driveline/axles
- DTC Index
- Electrical
- Electrical Component Locations
- Electronic Suspension
- Emission Applications
- Engine
- Engine Performance
- Exhaust
- Exterior Body Panels
- Exterior/interior Trim
- Fuel System
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- General Servicing - All Makes
- Heated Glass/defoggers
- Identification
- Ignition System
- Manual Trans
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Metric Conversions
- Mirrors
- Mode 6
- Oem General Information
- Procedures
- Reset Procedures
- Restraints
- Seats
- Specifications
- Starter
- Steering
- Steering Column Switches
- Sun Roof/t-Top/convertible Top
- Suspension Front
- Suspension Rear
- Testing & Diagnostics
- Timing Belt
- Traction Control Disable
- Transmission
- Warning System
- Wheel Alignment
- Windows
- Wiper/washer Systems