Test the vehicle under the same conditions that the customer reported in order to verify the system is operating properly.
Home/Buick/Park Avenue/Buick Park Avenue II рестайлинг (2002-2005)/Repair manual/Mechanical/Intermittent
Contents
Section: Mechanical- Fastener Tightening Specifications
- Engine Mechanical Specifications
- Diagnostic Starting Point-Engine Mechanical
- Strategy Based Diagnostics
- Visual/physical Inspection
- Intermittent
- Symptom List
- Engine Compression Test
- Cylinder Leakage Test
- Oil Consumption Diagnosis
- Low or No Oil Pressure
- Oil Pressure Testing
- Diagnostic Aids
- Test Description
- Removal Procedure
- Engine Mount Inspection
- Engine Support Fixture
- Installation Procedure
- Valve Rocker Arm and Push Rod Replacement
- Valve Stem Oil Seal and Valve Spring Replacement
- Crankshaft Balancer Replacement
- Crankshaft Front Oil Seal Replacement
- Engine Front Cover Replacement
- Oil Filter Adapter and Bypass Valve Assembly Replacement
- Timing Chain and Sprockets Replacement
- Cylinder Head Replacement-Left
- Cylinder Head Replacement-Right
- Engine Oil Pressure Sensor And/or Switch Replacement
- Engine Flywheel Replacement
- Crankshaft Rear Oil Seal Replacement
- Crankshaft Rear Oil Seal and Housing Replacement
- Engine Replacement
- Engine Final Test and Inspection
- Crankshaft Balancer Removal
- Intake Manifold Removal-Lower (L36)
- Intake Manifold Removal-Lower (L67)
- Oil Pan Removal
- Crankshaft Front Oil Seal Removal
- Balance Shaft Removal
- Crankshaft Rear Oil Seal Removal
- Piston, Connecting Rod, and Bearing Removal
- Crankshaft and Bearings Removal
- Camshaft Bearing Removal
- Balance Shaft Bearing And/or Bushing Removal
- Engine Block Cleaning and Inspection
- Boring Procedure
- Honing Procedure
- Crankshaft and Bearings Cleaning and Inspection
- Bearing Selection
- Method A
- Method B
- Piston and Connecting Rod Disassemble
- Piston, Connecting Rod, and Bearings Cleaning and Inspection
- Camshaft and Bearings Cleaning and Inspection
- Valve Rocker Arm and Push Rods Cleaning and Inspection
- Cylinder Head Disassemble
- Cylinder Head Cleaning and Inspection
- Valve Guide Reaming/valve and Seat Grinding
- Cylinder Head Assemble
- Oil Pump Cleaning and Inspection
- Thread Repair
- Service Prior to Assembly
- Engine Prelubing
- Balance Shaft Bearing And/or Bushing Installation
- Camshaft Bearing Installation
- Engine Block Plug Installation
- Crankshaft and Bearings Installation
- Piston, Connecting Rod, and Bearing Installation
- Crankshaft Rear Oil Seal and Housing Installation
- Crankshaft Rear Oil Seal Installation
- Balance Shaft Installation
- Timing Chain and Sprockets Installation (L36)
- Timing Chain and Sprockets Installation (L67)
- Oil Filter Adapter Installation
- Engine Front Cover Installation
- Crankshaft Front Oil Seal Installation
- Cylinder Head Installation-Right
- Cylinder Head Installation-Left
- Valve Rocker Arm and Push Rod Installation
- Exhaust Manifold Installation-Right
- Exhaust Manifold Installation-Left
- Exhaust Gas Recirculation (EGR) and EGR Pipe Installation
- Engine Flywheel Installation
- Crankshaft Balancer Installation
- Drive Belt System Description
- Engine Construction
- Description
- Operation
- New Product Information
- Component Comparison
- Fastener Changes
- Torque Values And/or Fastener Tightening Strategies
- Changed Engine Specifications
- New Sealants And/or Adhesives
- Disassembly and Assembly Procedure Revisions
- Engine Mechanical Diagnostic Procedure Revisions
- New Special Tools Required
- Cleanliness and Care
- Separating Parts
- Replacing Engine Gaskets
- Use of Rtv and Anaerobic Sealer
- Applying Rtv Sealer
- Applying Anaerobic Sealer
- Tools and Equipment
- Abbreviations
- Accessories Control Systems
- Accessory Drive Belts
- Adjustments
- Airbag
- Antilock Brake System
- Automatic Trans
- Automatic Transaxle Overhaul & Testing - 4t65-e
- Automatic Transmission Servicing
- Axle Shafts
- Basic Trouble Shooting
- Battery
- Body Electrical
- Body Front End
- Body Rear End
- Brakes
- Cabin Air Filter
- Cellular Communication System
- Charging System
- Check Lists
- Collision/avoidance
- Communication Devices
- Computer Relearn
- Cooling Fan
- Cruise Control Systems
- Diagnostic Connector Locations
- Door Locks & Anti-Theft Systems
- Door System, Mirror System & Window System
- Drive Cycles
- Driveline/axles
- DTC Index
- Electrical Component Locations
- Electronic Steering
- Electronic Suspension
- Emission Applications
- Engine
- Engine Control System Self-Diagnostics - 3.8l
- Engine Cooling System
- Engine Performance
- Engine/vin Breakdown
- Entertainment System
- Exhaust
- Exterior Body Panels
- Exterior/interior Trim
- Frames, Subframes & Crossmembers
- Fuses & Circuit Breakers
- Heating, Ventilation and Air Conditioning
- Hoist/jack
- Horns
- HVAC Systems - Automatic
- Identification
- Instrument Panel, Gages, and Console
- Lighting Systems
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Memory Modules
- Metric Conversions
- Mode 6
- Oem General Information
- Power Steering System
- Removal & Installation
- Reset Procedures
- Restraints
- Restraints Control Systems
- Rpo Codes
- Seat System
- Sensor Range Charts
- Specifications
- Starter
- Stationary Window System
- Steering
- Steering Wheel & Steering Column
- Sunroof System
- Suspension Front
- Suspension Rear
- Testing & Diagnostics
- Theory & Operation
- Traction Control Disable
- Transmission
- Vibration Symptoms Diagnosis and Correction
- Warning System
- Wheel & Tire System
- Wheel Alignment
- Wiper System and Washer System
- Wiring Systems (general Information)