Manual sections
Wiring diagrams- Abbreviations
- Accessories Control Systems
- Accessory Drive Belts
- Adjustments
- Airbag
- Anti-Lock/traction Control
- Application
- Automatic HVAC System
- Automatic Trans
- Axle Shafts
- Basic Trouble Shooting
- Body Electrical
- Brakes
- Cabin Air Filter
- Charging System
- Check Lists
- Communication Devices
- Computer Relearn
- Cooling Fan
- Cooling System (Mechanical)
- Cruise Control Systems
- Diagnostic Connector Locations
- Door Locks & Anti-Theft Systems
- Drive Cycles
- Driveline/axles
- DTC Index
- Electrical
- Electrical Component Locations
- Emission Applications
- Engine
- Engine Performance
- Entertainment Systems
- Exhaust
- Exterior Body Panels
- Exterior Lights
- Exterior/interior Trim
- Frames, Subframes & Crossmembers
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- Heated Glass/defoggers
- Hoist/jack
- Horns
- Identification
- Ignition Switch/steering Lock
- Manual & Power Steering
- Manual HVAC System
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Memory Modules
- Metric Conversions
- Mode 6
- Oem General Information
- Removal & Installation
- Reset Procedures
- Restraints
- Restraints Control Systems
- Rpo Codes
- Seats
- Sensor Range Charts
- Specifications
- Starter
- Steering
- Sun Roof/t-Top/convertible Top
- Suspension Front
- Suspension Rear
- Testing & Diagnostics
- Theory & Operation
- Traction Control Disable
- Transmission
- Warning System
- Wheel & Tire System
- Wheel Alignment
- Wiper/washer Systems
Repair manual
Mechanical Buick Century VI
Step-by-step instructions on "Mechanical" for Buick Century VI (1997–2005). Pick an article — removal, installation, adjustment and diagnostics with illustrations.
92articles
400illustrations
Articles in this section
92 articles- Fastener Tightening Specifications
- Engine Mechanical Specifications 6
- Diagnostic Starting Point - Engine Mechanical
- Strategy Based Diagnostics
- Visual/physical Inspection
- Intermittent
- Symptom List 16
- Engine Compression Test
- Testing Procedure
- Oil Consumption Diagnosis
- Low or No Oil Pressure
- Oil Pressure Testing
- Oil Leak Diagnosis
- Locating and Identifying the Leak
- Visual Inspection Method
- Powder Method
- Black Light and Dye Method
- Possible Causes for Leaks 1
- Diagnostic Aids
- Test Description 9
- Engine Mount Inspection
- Engine Support Fixture 32
- Installation Procedure 4
- Valve Rocker Arm and Push Rod Replacement 2
- Valve Stem Oil Seal and Valve Spring Replacement
- Removal Procedure 4
- Crankshaft Balancer Replacement
- Oil Pan Replacement 10
- Crankshaft Front Oil Seal Replacement 26
- Cylinder Head Replacement - Left 5
- Cylinder Head Replacement - Right 7
- Connecting Rod Bearing Replacement 3
- Engine Flywheel Replacement 4
- Crankshaft Rear Oil Seal Replacement 17
- Crankshaft Balancer Removal 41
- Crankshaft Front Oil Seal Removal 8
- Piston, Connecting Rod, and Bearing Removal 5
- Camshaft Bearing Removal 7
- Engine Block Cleaning and Inspection 5
- Boring Procedure 7
- Crankshaft and Bearings Cleaning and Inspection 8
- Bearing Selection
- Method A 1
- Method B 3
- Piston and Connecting Rod Disassemble 4
- Piston, Connecting Rod, and Bearings Cleaning and Inspection 16
- Piston and Connecting Rod Assemble 5
- Camshaft and Bearings Cleaning and Inspection 6
- Valve Rocker Arm and Push Rods Cleaning and Inspection 2
- Cylinder Head Disassemble 3
- Cylinder Head Cleaning and Inspection 5
- Valve Guide Reaming/valve and Seat Grinding 8
- Cylinder Head Assemble 9
- Oil Pump Cleaning and Inspection 6
- Oil Pump Assemble 8
- Intake Manifold Cleaning and Inspection - Lower 12
- Thread Repair 2
- Service Prior to Assembly
- Engine Prelubing 2
- Camshaft Bearing Installation 3
- Crankshaft and Bearings Installation 3
- Crankshaft Rear Oil Seal Installation 1
- Piston, Connecting Rod, and Bearing Installation 15
- Crankshaft Front Oil Seal Installation 6
- Cylinder Head Installation - Left 3
- Cylinder Head Installation - Right 6
- Valve Rocker Arm and Push Rod Installation 3
- Intake Manifold Installation - Lower 15
- Exhaust Manifold Installation - Left 2
- Exhaust Manifold Installation - Right 10
- Crankshaft Balancer Installation 2
- Rotating the Engine for Service Access 1
- General Description 1
- Operation 1
- Drive Belt System Description
- Engine Component Description
- New Product Information
- Component Comparison
- Fastener Changes
- Torque Values And/or Fastener Tightening Strategies
- Changed Engine Specifications
- New Sealants And/or Adhesives
- Disassembly and Assembly Procedure Revisions
- Engine Mechanical Diagnostic Procedure Revisions
- New Special Tools Required 3
- Cleanliness and Care
- Separating Parts
- Replacing Engine Gaskets
- Use of Rtv and Anaerobic Sealer
- Applying Rtv Sealer
- Applying Anaerobic Sealer
- Tools and Equipment 6