Home ReviewsRefund
Home/Opel/Agila/Opel Agila B (2008-2011)/Repair manual/Engine Mechanics - D13A/Special Tools
Contents Wiring diagrams Section: Engine Mechanics - D13A All sections

Special Tools Opel Agila B

Engine Mechanics - D13A 45 illustrations
CH-48373Fixture, engine/transmission/front axle body
For removing and installing front axle body with engine and transmission assembly (in conjunction with KM-904 and hydraulic jack). For supporting engine from beneath with engine mount removed
CH-48373-100Frame mounts and supports
For removing and installing front axle body with engine and transmission assembly (in conjunction with CH-48373)
EN-46775Centring Tool
Centring timing chain cover during installation
EN-46776Seal Installer
To install front oil seal to timing chain cover
EN-46777Seal Installer
To install crankshaft rear oil seal to engine
EN-46778Crankshaft Positioning Tool
To position crankshaft when transmission and clutch removed
EN-46779Installer
To install valve stem oil seals
EN-46781Camshaft Positioning Tool
To position camshaft
EN-46782Compression Adapter
To check engine compression or engine pressure loss (in conjunction with EN-46783)
EN-46783Adapter
To check engine compression or engine pressure loss (in conjunction with EN-46782)
EN-46785Crankshaft Positioning Tool
To position crankshaft when transmission installed
EN-47632Cleaner
To clean fuel injector bores
EN-47649Engine Bridge
To support engine and transmission assembly
EN-47649–100Engine Bridge Feet
For use with EN-47649
EN-47650Carrier Frame
For use with EN-47649
EN-47650–200Rear Adapter Support
For use with EN-47650
EN-49110Lifting Eye
For use with KM-2358
KM-113-2Mount for Assembly Device
Used with KM-6215 Assembly Device
KM-135Adapter
Used with KM-498-B to check engine oil pressure
KM-301Measuring Bridge
Used with Dial Test Indicator MKM-571-B to measure piston protrusion
KM-412-AEngine Stand
To hold removed engine
KM-412-32Engine Stand Adapter
To hold engine in conjunction with KM-412-A
KM-427Drift
To install dowel pins
KM-470-BAngular Torque Wrench
To secure cylinder head bolts
KM-498-BFluid Pressure Gauge
To check engine oil pressure
KM-507-CRemover
To release tie rod end from steering knuckle
KM-652Flywheel Locking Tool
To lock flywheel when removing and installing clutch or flywheel
KM-662-CHolding Wrench
To counterhold crankshaft when releasing bolt
KM-807Sealing Plugs
To seal fuel lines
KM-840Remover
To remove valve stem seal
KM-849Storage Facility
Storage facility for pistons, con-rods, valves etc.
KM-904Base Frame
For removing and installing front axle body with engine and transmission assembly (in conjunction with CH-48373 and hydraulic jack)
KM-955Locking Pin
To lock timing chain tensioner when removing and installing
KM-956-1Handle
Handle for Holding Wrench KM-6610
KM-2358Wire Rope
To support engine
KM-6015Sealing Plugs
To seal the fuel lines
KM-6130Locating Pin
To lock ribbed V- belt tensioner when removing and installing belt
KM-6167Adapter Set
Assembly device for operations on cylinder head
KM-6171Release tool
To release valve
KM-6215Assembly Device
Assembly device for operations on cylinder head
KM-6282Remover
To release axle shaft from wheel hub
KM-6347Holder
To counterhold camshaft when releasing bolt
KM-6610Holding Wrench
To counterhold axle shaft. Fasten to wheel hub with wheel bolts
KM-J-37228Seal Breaker
For cutting through sealant to separate components
MKM-571-BDial Test Indicator
Used with Measuring Bridge KM-301 to measure piston protrusion
MKM-667Vacuum Gauge Tool
For checking turbocharger wastegate actuator
MKM-6086To install/remove valve collets (6 mm)
To remove and install valve springs and valve collets

More articles — Engine