Recommended Torque Values
| Nm |
|---|
| Starter motor to transmission | 75 |
| Starter to cylinder block | 45 |
| Balancer gear (balancer shaft unit) to crankshaft bearing cap | 20 + 45� |
| Balancer gear (balancer shaft unit) to cylinder block | 20 + 45 |
| Exhaust manifold to cylinder head | 22 |
| Fuel pressure regulator fastening clamp | 5 |
| DIS ignition module to adapter (coolant flange) | 8 |
| Dome brace to spring strut dome | 47 |
| Dome brace to air deflector panel | 25 |
| Torque support to main bracket | 53 |
| Torsional vibration damper to toothed belt drive pulley | 20 |
| Throttle body to intake manifold | 9 |
| Intake manifold pressure sensor to intake manifold | 8 |
Recommended Torque Values
| Nm |
|---|
| Intake manifold to cylinder head | 22 |
| Engine vent flange to cylinder block | 25 |
| Accelerator pedal bracket to bulkhead | 10 |
| Temperature regulator housing (heat exchanger) to oil pump | 23 |
| Transmission to cylinder block | 75 |
| Crankshaft pulse pick�up sensor disc to crankshaft | 13 |
| Oil filter threaded connector to temperature regulator housing | 30 |
| Torque support main bracket to transmission | 53 |
| Torque support bracket to cylinder block | 53 |
| Torque support bracket to air deflector panel | 26 |
| Ancillary components main bracket to cylinder block | 35 |
| Alternator bracket to cylinder block | 35 |
| Right�hand engine damping block bracket to oil pan | 53 |
Recommended Torque Values
| Nm |
|---|
| Oil intake pipe bracket to balancer gear (balancer shaft unit) (M6) | 10 |
| Oil intake pipe bracket to balancer gear (balancer shaft unit) (M8) | 20 |
| Guide roller bracket to cylinder block | 25 |
| Rear toothed belt cover to oil pump | 6 |
| Rear toothed belt cover to cylinder head | 6 |
| Axle shaft heat shield to transmission and cylinder block | 47 |
| Crankshaft pulse pick�up to cylinder block | 8 |
| Refrigerant line to accumulator/dryer and condenser | 16 |
| Ribbed V�belt tension roller to ancillary components main bracket | 20 |
| Knock sensor to cylinder block | 20 |
| Fuel distributor pipe to intake manifold | 8 |
| Coolant pump to cylinder block | 25 |
Recommended Torque Values
| Nm |
|---|
| Crankshaft bearing cap to cylinder block | 50 + 45�+ 15� |
| Oxygen sensor to front exhaust pipe | 50 |
| Alternator shackle to alternator, intake manifold and coolant flange | 20 |
| Fan housing to radiator | 4 |
| Engine damping block (left) to transmission | 53 |
| Engine damping block (left) to front axle body | 53 |
| Engine damping block (right) to bracket | 53 |
| Engine damping block (right) to front axle body | 53 |
| Engine transport shackle to cylinder head | 20 |
| Camshaft bearing cap to cylinder head | 8 |
| Camshaft pulleys to camshaft | 50 + 60� + 15� |
Recommended Torque Values
| Nm |
|---|
| Camshaft sensor to cylinder head | 6 |
| Oil drain plug to oil pan (Torx bolt) | 10 |
| Oil drain plug to oil pan (hexagon head bolt) | 55 |
| Oil pressure switch to oil pump | 40 |
| Oil filter to temperature regulator housing (heat exchanger) | 15 |
| Heat exchanger oil pipes to heat exchanger | 30 |
| Heat exchanger oil pipes to temperature regulator housing (heat exchanger) | 30 |
| Oil pump to cylinder block | 8 |
| Oil pump cover to oil pump | 6 |
| Oil intake pipe to oil pump | 8 |
| Oil pan to transmission housing | 43 |
| Oil pan to cylinder block | 20 |
Recommended Torque Values
| Nm |
|---|
| Con�rod bearing cap to con�rod | 35 + 45� + 15� |
| Power steering pump to ancillary components main bracket | 20 |
| Wheel to wheel hub | 140 |
| Flywheel to crankshaft | 65 + 30� + 15� |
| Coolant temperature sensor to DIS ignition module adapter (coolant flange) | 11 |
| Tie rod end to steering knuckle | 30 + 115� |
| Intake manifold support to cylinder block and intake manifold | 25 |
| Alternator support to alternator and intake manifold | 20 |
| Thermostat housing to cylinder head | 15 |
| Temperature regulator blanking plug to temperature regulator housing (heat exchanger) | 20 + 60� + 30� |
Recommended Torque Values
| Nm |
|---|
| Safety valve blanking plug to oil pump | 30 |
| Front axle body to chassis | 160 |
| From toothed belt cover to rear toothed belt cover | 6 |
| Heat exchanger (coolant pipe) to cylinder block | 15 |
| Toothed belt tension roller to oil pump | 20 |
| Toothed belt guide roller to guide roller bracket | 25 |
| Toothed belt guide roller to cylinder block | 25 |
| Toothed belt pulley to crankshaft | 130 + 40� to 50� |
Recommended Torque Values
| Nm |
|---|
| Ignition cable cover to cylinder head cover | 3 |
| Spark plugs to cylinder head | 25 |
| Intermediate shaft to steering gear | 45 |
| Cylinder head to cylinder block | 25 + 90� + 90� + 90� + 15� |
| Cylinder head cover to cylinder head | 8 |
