Home ReviewsRefund
Home/Opel/Combo/Opel Combo C (2002-2011)/Repair manual/OHC Petrol Engine/Special Service Tools
Contents Wiring diagrams Section: OHC Petrol Engine All sections

Special Service Tools Opel Combo C

OHC Petrol Engine 45 illustrations
KM-194-ESpark Plug Key
To remove/install spark plug
KM-235-DInstaller
To install crankshaft rear seal ring in conjunction with KM-658
KM-313Slide Hammer
To remove axle shafts in conjunction with KM-902
KM-412Engine Overhaul Stand
To hold removed engine
KM-412-10Adapter
To hold engine in conjunction with KM-412
KM-417Assembly Sleeve
Installation of oil pump and crankshaft front seal ring
KM-421-AAdjusting Wrench
KM-422Installer
To press seal ring in camshaft
KM-468-BHolding Wrench
Counterholding of wheel hub when installing axle nut
KM-470-BAngular Torque Wrench
KM-471Adapter
To check pressurised cooling system in conjunction with cooling system tester
KM-498-BOil pressure gauge
To check engine oil pressure
KM-507-CRemover
Pressing out of tie rods
KM-527-AAdjustment pin
Locking transmission shift linkage
KM-558-10Closure cover
KM-565-ARemover / Installer
To remove and install rocker arms and valve play compensator
MKM-596-ATemperature measuring instrument
To measure oil temperature
KM-604-DTorx Bit and Socket Set
MKM-610Torque wrench, 1/2"
Range 30 – 130 Nm / 22 – 96 lbf. ft.
MKM-611Torque wrench, 3/8"
Range 10 – 60 Nm / 7 – 44 lbf. ft.
KM-652Flywheel Holder
To lock flywheel or drive disc
KM-658Installer
To install rear crankshaft seal ring in conjunction with KM-235-1
MKM-669Torque wrench, 1/2"
Range 50 – 300 Nm / 37 – 221 lbf. ft.
KM-726-AOil Filter Wrench
KM-734Guide Drift
To centre clutch disc
KM-807Closure Plugs
KM-835-AInstaller
To install valve seals
KM-840Pliers
To remove valve stem seals
MKM-891Valve compressor
Camshaft removal and installation (cylinder head installed)
KM-902Remover
To remove axle shafts in conjunction with KM-313
KM-904Base Frame
To remove/install engine and transmission with KM-6168
KM-911Flywheel Holder
To lock flywheel or drive disc
KM-947Remover / Installer
Oil dipstick tube

Rear crankshaft sealing ring installation

KM-2358Wire Cable
To suspend engine
KM-6130Locating Pin
To fasten Ribbed V-belt tensioner
KM-6168Centring Tool
To remove and install front axle (with drive unit) in conjunction with KM-904
KM-6169Engine/Transmission Mount
Fixing of engine/transmission to front axle body
KM-6179Installation wrench, oxygen sensor
To remove and install oxygen sensor
KM-6181Arresting Steering Shaft
Steering intermediate shaft adjustment
KM-6182-1Pliers, straight
Removal/installation of compact clamps
KM-6182-2Pliers, curved
Removal/installation of compact clamps
KM-6182-3Pliers, flexible shaft
Removal/installation of compact clamps
KM-6347Holder
For removing/installing camshaft sprockets/torsional vibration damper
KM-J-7004Slide hammer

To tension ribbed V-belt tension roller

KM-J-34730-91Pressure Tester
To check fuel pressure

More articles — Engine and Engine Aggregates