Selector Lever Cable Replacement Opel Agila B

Remove

1. 1. Release front section of centre console from vehicle • Remove 2x clip (1)
2. 2. Slide and tilt 2x seat forward
3. 3. Remove centre console from vehicle • Remove 2x clip (2) from rear of centre console • Disconnect 2x harness connector from 2x heater mat switch • Release harness for 2x heater mat switch from centre console – Release clip

4. 4. Slide and tilt 2x seat backward
5. 5. Remove lower trim strip (1) from upper trim strip and lower centre instrument trim panel • Prise off to release 6x clip, 3x locator
6. 6. Remove selector lever trim cover (2) from lower centre instrument trim panel • Prise off to release 6x clip, 2x locator
7. 7. Remove upper trim strip (3) from instrument panel and lower centre instrument trim panel • Open upper storage compartment • Release upper trim strip from upper storage compartment – Remove clip • Remove 2x screw • Prise off to release 10x clip

8. 8. Remove lower centre instrument trim panel from vehicle • Remove 4x screw (1), 4x clip (2) • Release lower centre instrument trim panel from 2x side bracket and selector lever bracket • Release 9x locator

9. 9. Remove side bracket (1) from instrument panel carrier and selector lever bracket, right side • Remove 4x bolt (2), then release locator

10. 10. Shift selector lever to neutral "N" position • Turn ignition switch to "ON" position, then apply foot brake • Turn ignition switch to "OFF" position
11. 11. Release selector lever cable (1) from selector lever assembly • Release ball joint, using suitable tool • Release clip, then slide off – Use suitable tool
12. 12. Remove retaining clip from selector lever cable • Slide off

13. 13. Release selector lever cable from retaining clip on top of transmission assembly • Pull off
14. 14. Raise vehicle
15. 15. Release 2x protective panelling from front panelling • Remove 4x clip (1)

16. 16. Release selector lever cable (1) from manual selector lever on transmission selector position sensor • Remove clip, then pull off
17. 17. Release selector lever cable from support bracket for transmission assembly • Remove clip – Prise off using suitable tool

18. 18. Remove selector lever cable (2) from vehicle • Remove 2x bolt (1) • Withdraw selector lever cable through aperture in bulkhead panel and from transmission assembly

Install

19. 19. Install new selector lever cable (2) to vehicle • Position selector lever cable to transmission assembly and through aperture in bulkhead panel • Install 2x bolt (1) 5.5 Nm

20. 20. Secure selector lever cable (1) to support bracket for transmission assembly • Install clip – Push on using suitable tool
21. 21. Secure selector lever cable to manual selector lever on transmission selector position sensor • Push on, then install clip

22. 22. Check needle lock washer and reference line (1) on transmission selector position sensor (3) are aligned
23. 23. Adjust transmission selector position sensor • Release 2x bolt (2) • Align needle lock washer and reference line on transmission selector position sensor • Secure 2x bolt 5.5 Nm

24. 24. Secure 2x protective panelling to front panelling • Install 4x clip (1)

25. 25. Lower vehicle
26. 26. Secure selector lever cable to retaining clip on top of transmission assembly • Push on
27. 27. Install retaining clip to selector lever cable (1) • Slide on

28. 28. Adjust selector lever cable (1) as necessary • Release lock from cable holder • Release cable holder from adjuster – Push out using suitable tool • Apply suitable lubricant to selector lever assembly • Secure selector lever cable and adjuster to selector lever assembly • Slide on to secure clip • Secure ball joint • Secure cable holder to adjuster – Push in • Secure lock to cable holder

Important. After adjusting selector lever cable, check the following.

29. 29. Perform "P" range test • Check reverse light is turned ON when shifting selector lever to "R" range • Check A/T shift position indicator (in instrument display) is consistent with selector lever range • Check selector lever position light operation is consistent with selector lever range • Check engine starts at "P" and "N" ranges • Check engine does not start at other than "P" and "N" ranges
30. 30. Install side bracket (1) to instrument panel carrier and selector lever bracket, right side • Secure locator, install 4x bolt 23 Nm

31. 31. Install lower centre instrument trim panel to vehicle • Secure lower centre instrument trim panel to 2x side bracket and selector lever bracket – Secure 9x locator • Install 4x clip (2), 4x screw (1)

32. 32. Install upper trim strip (3) to instrument panel and lower centre instrument trim panel • Push on to secure 10x clip • Install 2x screw • Secure upper trim strip to upper storage compartment – Install clip • Close upper storage compartment
33. 33. Install selector lever trim cover (2) to lower centre instrument trim panel • Push on to secure 2x locator, 6x clip
34. 34. Install lower trim strip (1) to upper trim strip and lower centre instrument trim panel • Push on to secure 3x locator, 6x clip
35. 35. Slide and tilt 2x seat forward

36. 36. Install centre console to vehicle • Connect 2x harness connector to 2x heater mat switch • Secure harness for 2x heater mat switch to centre console – Secure clip • Install 2x clip (2) to rear of centre console
37. 37. Slide and tilt 2x seat rearward
38. 38. Secure front section of centre console to vehicle • Install 2x clip (1)