Home ReviewsRefund
Home/Opel/Agila/Opel Agila B (2008-2011)/Repair manual/Automatic Transmission - 80-40LS/Selector Lever Position Switch Replacement
Contents Wiring diagrams Section: Automatic Transmission - 80-40LS All sections

Selector Lever Position Switch Replacement Opel Agila B

Automatic Transmission - 80-40LS ~603 words

Remove

  1. 1. Slide and tilt 2x seat backward
  2. 2. Release front section of centre console from vehicle • Remove 2x clip (1)
  3. 3. Slide and tilt 2x seat forward
  4. 4. Remove centre console from vehicle • Remove 2x clip (2) from rear of centre console • Disconnect 2x harness connector from 2x heater mat switch • Release harness for 2x heater mat switch from centre console – Release clip
  1. 5. Slide and tilt 2x seat backward
  2. 6. Remove lower trim strip (1) from upper trim strip and lower centre instrument trim panel • Prise off to release 6x clip, 3x locator
  3. 7. Remove selector lever trim cover (2) from lower centre instrument trim panel • Prise off to release 6x clip, 2x locator
  4. 8. Remove upper trim strip (3) from instrument panel and lower centre instrument trim panel • Open upper storage compartment • Release upper trim strip from upper storage compartment – Remove clip • Remove 2x screw • Prise off to release 10x clip
  1. 9. Remove lower centre instrument trim panel from vehicle • Remove 4x screw (1), 4x clip (2) • Release lower centre instrument trim panel from 2x side bracket and selector lever bracket • Release 9x locator
  1. 10. Remove side bracket (1) from instrument panel carrier and gearshift lever bracket, right side • Remove 4x bolt (2), then release locator
  1. 11. Disconnect harness connector (1) from selector lever lock solenoid, selector lever position switch and illumination lamp harness connector
  2. 12. Release 2x terminal for selector lever position switch from harness connector • Use Harness Repair Kit MKM-923
  3. 13. Remove selector lever position switch from selector lever assembly • Release harness from 4x clip, then withdraw through aperture in selector lever assembly • Release switch (2) from selector lever assembly – Prise out to release 3x clip

Install

  1. 14. Install new selector lever position switch to selector lever assembly • Secure switch (2) to selector lever assembly – Push in to secure 3x clip • Position harness through aperture in selector lever assembly, then secure to 4x clip
  2. 15. Secure 2x terminal for selector lever position switch to harness connector • Use Harness Repair Kit MKM-923
  3. 16. Connect harness connector (1) to selector lever lock solenoid, selector lever position switch and illumination lamp harness connector
  1. 17. Install side bracket (1) to instrument panel carrier and selector lever bracket, right side • Secure locator, then install 4x bolt (2) 23 Nm
  1. 18. Install lower centre instrument trim panel to vehicle • Secure lower centre instrument trim panel to 2x side bracket and selector lever bracket – Secure 9x locator • Install 4x clip (2), 4x screw (1)
  1. 19. Install upper trim strip (3) to instrument panel and lower centre instrument trim panel • Push on to secure 10x clip • Install 2x screw • Secure upper trim strip to upper storage compartment – Install clip • Close upper storage compartment
  2. 20. Install selector lever trim cover (2) to lower centre instrument trim panel • Push on to secure 2x locator, 6x clip
  3. 21. Install lower trim strip (1) to upper trim strip and lower centre instrument trim panel • Push on to secure 3x locator, 6x clip
  4. 22. Slide and tilt 2x seat forward
  1. 23. Install centre console to vehicle • Connect 2x harness connector to 2x heater mat switch • Secure harness for 2x heater mat switch to centre console – Secure clip • Install 2x clip (2) to rear of centre console
  2. 24. Slide and tilt 2x seat backward
  3. 25. Secure front section of centre console to vehicle • Install 2x clip (1)

More articles — Transmission/transaxle