Home ReviewsRefund
Home/Opel/Agila/Opel Agila B (2008-2011)/Repair manual/Automatic Transmission - 80-40LS/Selector Lever Cable Adjust
Contents Wiring diagrams Section: Automatic Transmission - 80-40LS All sections

Selector Lever Cable Adjust Opel Agila B

Automatic Transmission - 80-40LS ~793 words

Remove

  1. 1. Disconnect battery negative lead • Release nut
  2. 2. Apply parking brake lever
  3. 3. Slide and tilt driver side seat rearward
  4. 4. Slide and tilt passenger side seat rearward
  5. 5. Release front section of centre console from vehicle • Remove 2x clip (1)
  6. 6. Slide and tilt driver side seat forward
  7. 7. Slide and tilt passenger side seat forward
  8. 8. Remove centre console from vehicle • Remove 2x clip (2) from rear of centre console • Disconnect 2x harness connector from 2x heater mat switch • Release harness for 2x heater mat switch from centre console – Release clip • Slide and tilt driver side seat rearward
  1. 9. Remove lower trim strip (1) from upper trim strip (3) and lower centre instrument trim panel • Prise off to release 6x clip, 3x locator, using suitable tool
  2. 10. Remove selector lever trim cover (2) from lower centre instrument trim panel • Prise off to release 6x clip, 2x locator, using suitable tool
  3. 11. Remove upper trim strip from instrument panel and lower centre instrument trim panel • Open upper storage compartment • Release upper trim strip from upper storage compartment – Remove clip • Remove 2x screw • Prise off to release 10x clip, using suitable tool
  1. 12. Remove lower centre instrument trim panel from vehicle • Remove 4x screw (2), 4x clip (1) • Release lower centre instrument trim panel from 2x side bracket and selector lever bracket • Release 9x locator
  1. 13. Remove side bracket (1) from instrument panel carrier and selector lever bracket, right side • Remove 4x bolt (2), then release locator
  1. 14. Shift selector lever to neutral "N" position • Turn ignition switch to "ON" position, then apply foot brake • Turn ignition switch to "OFF" position
  2. 15. Raise vehicle
  3. 16. Release 2x protective panelling from front panelling • Remove 4x clip (1)

Adjust

  1. 17. Check needle lock washer and reference line (1) on transmission selector position sensor (3) are aligned
  2. 18. Adjust transmission selector position sensor • Release 2x bolt (2) • Align needle lock washer and reference line on transmission selector position sensor • Secure 2x bolt 5.5 Nm

Install

  1. 19. Secure 2x protective panelling to front panelling • Install 4x clip (1)
  1. 20. Lower vehicle
  2. 21. Adjust selector lever cable (1) as necessary • Release lock from cable holder • Release cable holder from adjuster – Push out using suitable tool • Apply suitable lubricant to selector lever assembly • Secure selector lever cable and adjuster to selector lever assembly • Slide on to secure clip • Secure ball joint • Secure cable holder to adjuster – Push in • Secure lock to cable holder

Important. After adjusting selector lever cable, check the following.

  1. 22. Perform "P" range test • Check reverse light is turned ON when shifting selector lever to "R" range • Check A/T shift position indicator (in instrument display) is consistent with selector lever range • Check selector lever position light operation is consistent with selector lever range • Check engine starts at "P" and "N" ranges • Check engine does not start at other than "P" and "N" ranges
  2. 23. Install side bracket (1) to instrument panel carrier and selector lever bracket, right side • Secure locator, install 4x bolt 23 Nm
  1. 24. Install lower centre instrument trim panel to vehicle • Secure lower centre instrument trim panel to 2x side bracket and selector lever bracket – Secure 9x locator • Install 4x clip (1), 4x screw (2)
  1. 25. Install upper trim strip (3) to instrument panel and lower centre instrument trim panel • Push on to secure 10x clip • Install 2x screw • Secure upper trim strip to upper storage compartment – Install clip • Close upper storage compartment
  2. 26. Install selector lever trim cover (2) to lower centre instrument trim panel • Push on to secure 2x locator, 6x clip
  3. 27. Install lower trim strip (1) to upper trim strip and lower centre instrument trim panel • Push on to secure 3x locator, 6x clip
  1. 28. Install centre console to vehicle • Slide and tilt driver side seat forward • Connect 2x harness connector to 2x heater mat switch • Secure harness for 2x heater mat switch to centre console – Secure clip • Install 2x clip (2) to rear of centre console
  2. 29. Slide and tilt driver side seat rearward
  3. 30. Slide and tilt passenger side seat rearward
  4. 31. Secure front section of centre console to vehicle • Install 2x clip (1)
  1. 32. Slide and tilt driver side seat to original position
  2. 33. Slide and tilt passenger side seat to original position
  3. 34. Connect battery negative lead • Secure nut 11 Nm
  4. 35. Program all volatile memories – see operation “Program Volatile Memories”

More articles — Transmission/transaxle