Ignition Key Interlock Cable Replacement Opel Agila B

Remove

1. 1. Disconnect battery negative lead • Release nut
2. 2. Apply parking brake lever
3. 3. Slide and tilt driver side seat rearward
4. 4. Slide and tilt passenger side seat rearward
5. 5. Release front section of centre console from vehicle • Remove 2x clip (1)
6. 6. Slide and tilt driver side seat forward
7. 7. Slide and tilt passenger side seat forward
8. 8. Remove centre console from vehicle • Remove 2x clip (2) from rear of centre console • Disconnect 2x harness connector from 2x heater mat switch • Release harness for 2x heater mat switch from centre console – Release clip • Slide and tilt driver side seat rearward

9. 9. Remove lower trim strip (1) from upper trim strip (3) and lower centre instrument trim panel • Prise off to release 6x clip, 3x locator, using suitable tool
10. 10. Remove selector lever trim cover (2) from lower centre instrument trim panel • Prise off to release 6x clip, 2x locator, using suitable tool
11. 11. Remove upper trim strip from instrument panel and lower centre instrument trim panel • Open upper storage compartment • Release upper trim strip from upper storage compartment – Remove clip • Remove 2x screw • Prise off to release 10x clip, using suitable tool

12. 12. Remove lower centre instrument trim panel from vehicle • Remove 4x screw (2), 4x clip (1) • Release lower centre instrument trim panel from 2x side bracket and selector lever bracket • Release 9x locator

13. 13. Remove side bracket (1) from instrument panel carrier and selector lever bracket, left side • Remove 4x bolt (2), then release locator

14. 14. Remove lower trim panel (1) from instrument panel • Release 10x clip
15. 15. Remove 2x canopy (2) from steering column • Remove 3x screw (3) • Remove ignition key • Release lower canopy from upper canopy – Release 7x clip

16. 16. Release key interlock cable from steering and ignition lock assembly • Turn ignition lock cylinder to "ACC" position • Release clip and slide out, using suitable tool • Turn ignition lock cylinder to "LOCK" position
17. 17. Release key interlock cable (2) from selector lever assembly • Release ball joint, using suitable tool • Release clip, then slide off – Use suitable tool
18. 18. Remove key interlock cable (1) from vehicle • Release key interlock cable from brake pedal mounting bracket and instrument panel harness – Release from 2x clip

Install

19. 19. Install new key interlock cable (1) to vehicle • Secure key interlock cable to brake pedal mounting bracket and instrument panel harness – Secure to 2x clip
20. 20. Secure key interlock cable to steering and ignition lock assembly • Turn ignition lock cylinder to "ACC" position • Slide in to secure clip • Turn ignition lock cylinder to "LOCK" position
21. 21. Shift selector lever to neutral "N" position • Turn ignition lock cylinder to "ACC" position, then apply foot brake
22. 22. Adjust key interlock cable as necessary • Release lock from key interlock cable and adjuster – Push out using suitable tool • Apply suitable lubricant to selector lever assembly • Secure key interlock cable (2) and adjuster to selector lever assembly – Slide on to secure clip • Secure ball joint • Secure lock to key interlock cable and adjuster – Push in
23. 23. Shift selector lever to park "P" position and check following conditions • With knob button released, ignition lock cylinder can be turned from "ACC" position to "LOCK" position • With knob button pressed, ignition lock cylinder cannot be turned from "ACC" position to "LOCK" position • Turn ignition lock cylinder to "LOCK" position

24. 24. Install 2x canopy (2) to steering column • Secure lower canopy to upper canopy – Secure 7x clip • Install ignition key • Install 3x screw (3)
25. 25. Install lower trim panel (1) to instrument panel • Secure 10x clip

26. 26. Install side bracket (1) to instrument panel carrier and selector lever bracket, left side • Secure locator, then install 4x bolt (2) 23 Nm

27. 27. Install lower centre instrument trim panel to vehicle • Secure lower centre instrument trim panel to 2x side bracket and selector lever bracket – Secure 9x locator • Install 4x clip (1), 4x screw (2)

28. 28. Install upper trim strip (3) to instrument panel and lower centre instrument trim panel • Push on to secure 10x clip • Install 2x screw • Secure upper trim strip to upper storage compartment – Install clip • Close upper storage compartment
29. 29. Install selector lever trim cover (2) to lower centre instrument trim panel • Push on to secure 2x locator, 6x clip
30. 30. Install lower trim strip (1) to upper trim strip and lower centre instrument trim panel • Push on to secure 3x locator, 6x clip

31. 31. Install centre console to vehicle • Slide and tilt driver side seat forward • Connect 2x harness connector to 2x heater mat switch • Secure harness for 2x heater mat switch to centre console – Secure clip • Install 2x clip (2) to rear of centre console
32. 32. Slide and tilt driver side seat rearward
33. 33. Slide and tilt passenger side seat rearward
34. 34. Secure front section of centre console to vehicle • Install 2x clip (1)

35. 35. Slide and tilt driver side seat to original position
36. 36. Slide and tilt passenger side seat to original position
37. 37. Connect battery negative lead • Secure nut 11 Nm
38. 38. Program all volatile memories – see operation “Program Volatile Memories”