Home ReviewsRefund
Home/Nissan/Pathfinder/Nissan Pathfinder III рестайлинг (2010-2014)/Repair manual/Windows/Roof: Adjustments
Contents Section: Windows All sections

Roof: Adjustments Nissan Pathfinder III рестайлинг

Windows 2 illustrations ~431 words

Adjustment

Inspect then measure the gap and height difference between the glass lid assembly and roof panel; compare to specifications. Determine which procedure to follow based on results of measurements.

Scheme 102

Scheme 102: Adjustment
Scheme 102: Adjustment

GAP ADJUSTMENT

If a gap or minor height difference between glass lid assembly and roof panel is found, adjust in the following manner

  1. Open sunshade assembly and tilt glass lid assembly up.
  2. Loosen glass lid assembly screws (two each on left and right sides), then tilt glass lid assembly down.
  3. Manually adjust glass lid assembly from outside of vehicle so it is within specification "A-A" as shown.
  4. After adjustment, tilt glass lid assembly up and tighten screws.
  5. Tilt glass lid assembly up and down several times to check that it moves and seals properly.

HEIGHT DIFFERENCE ADJUSTMENT

If an excessive height difference between glass lid assembly and roof panel is found, adjust in the following manner

  1. Remove headlining. Refer to " «REMOVAL AND INSTALLATION»(ref-519822-S39057959832012122900000) ".
  2. Loosen sunroof unit nuts and sunroof bracket bolts.
  3. Add shims until gap is within specification "A-A" as shown. NOTE: Temporarily snug nuts and bolts to prevent movement between each adjustment.
  4. Tilt glass lid assembly up and down several times to check that it moves and seals properly.
  5. Tighten sunroof unit nuts and sunroof bracket bolts. NOTE: First tighten left front then right rear sunroof unit nuts to prevent uneven torque while tightening remaining sunroof bracket bolts.
  6. Install headlining. Refer to " «REMOVAL AND INSTALLATION»(ref-519822-S39057959832012122900000) ".

Scheme 103

Scheme 103: Removal and Installation
Scheme 103: Removal and Installation
CAUTIONAlways work with a helper. Handle glass lid assembly with care so not to cause damage. Before removal, fully close the glass lid assembly. Then, after removal, do not move the motor assembly. After installing the sunroof and glass lid assembly, check gap adjustment to ensure there is no malfunction.

Note. After any adjustment, check sunroof operation and glass lid assembly alignment. For easier installation, mark each point before removal.

Removal

CAUTIONWhen taking sunroof unit out, use shop cloths to protect the seats and trim from damage.
  1. Remove headlining. Refer to " «REMOVAL AND INSTALLATION»(ref-519822-S39057959832012122900000) ".
  2. Remove the glass lid assembly. Refer to «GLASS LID ASSEMBLY»(ref-519840-S24110233702012122900000) procedure in this article.
  3. Disconnect sunroof motor assembly, and remove the front roof console bracket.
  4. Disconnect the drain hoses.
  5. Remove front sunroof unit nuts.
  6. Remove the rear sunroof bracket bolts.
  7. Remove the side nuts, then lower the sunroof unit from the roof panel opening.
  8. Remove the sunshade assembly from the rear end of the sunroof unit. Refer to «SUNSHADE ASSEMBLY»(ref-519840-S33017191822012122900000) procedure in this article

Installation

  1. Install the sunshade assembly to the rear end of the sunroof unit. Refer to «SUNSHADE ASSEMBLY»(ref-519840-S33017191822012122900000) procedure in this article
  2. Position the sunroof unit and install the side nuts.
  3. Install the rear sunroof brackets and bolts.
  4. Install front sunroof unit nuts.
  5. Connect the drain hoses.
  6. Install the front roof console bracket, then connect the sunroof motor assembly.
  7. Install the glass lid assembly. Refer to «GLASS LID ASSEMBLY»(ref-519840-S24110233702012122900000) procedure in this article.
  8. Install headlining. Refer to " «REMOVAL AND INSTALLATION»(ref-519822-S39057959832012122900000) ".

More articles — Roof