4.7L Engine - Service Information: Component Locations RAM Pickup 2500

SPECIAL TOOLS

10101 - Fixture, Engine Lifting (Originally Shipped In Kit Number(s) 10100, 10109.) 10102 - Remover/Installer, Valve Spring (Originally Shipped In Kit Number(s) 10100, 10109.) 1023 - Puller (Originally Shipped In Kit Number(s) 8678.) 10368 - Set, Universal Protective Cap 6871 - Installer, A/C Hub (Originally Shipped In Kit Number(s) 6896.) 6958 - Wrench, Spanner (Originally Shipped In Kit Number(s) 6947, 6949, 6966, 8204, 8204CC, 8667.) 7700 - Tester, Cooling System (Originally Shipped In Kit Number(s) 7700-A.) 8346 - Pins, Adapter (Originally Shipped In Kit Number(s) 8503, 8510, 8520, 8520CC.) 8348 - Installer, Seal (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) 8349 - Installer, Crankshaft Rear Oil Seal (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC.) 8349-2 - Guide Crank Seal (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC.) 8428A - Holder, Camshaft (Originally Shipped In Kit Number(s) 10134, 10134, 9975.) 8429 - Holder, Secondary Camshaft Chain (Originally Shipped In Kit Number(s) 8703, 8703CC, 8712, 9975.) 8454 - 3-Jaw Puller (Originally Shipped In Kit Number(s) 8673, 8675, 8676, 8709, 8709CC.) 8506 - Remover, Seal (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC.) 8507 - Guides, Connecting Rod (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC.) 8511 - Remover, Seal (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) 8512A - Installer, Damper (Originally Shipped In Kit Number(s) 8283, 8527, 8575, 8575CC, 8660, 8661.) 8513A - Insert, Crankshaft (Originally Shipped In Kit Number(s) 8283, 8527, 8575, 8999, 8999CC.) 8514 - Pins, Tensioner (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) 8516A - Remover/Installer (Originally Shipped In Kit Number(s) 8283, 8527, 8534B, 8575, 9090, 9300, 9975.) 8517 - Remover (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) 8519 - Adapters, Valve Spring (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) 8534B - Fixture, Driveline Support (Originally Shipped In Kit Number(s) 8534, 8534B, 8849, 9565.) 9867 - Wedge, Locking (Originally Shipped In Kit Number(s) 9998, 9999.) C-119 - Cylinder Indicator C-3292A - Gauge, Pressure C-3339A - Set, Dial Indicator (Originally Shipped In Kit Number(s) 9202.) C-3422-D - Compressor, Valve Spring C-3501 - Hone W/Oil, AMMCO Cylinder C-3501-3810 - Stones, 220 Grit Honing C-3501-3880 - Oil, Honing C-3685-A - Bloc-Chek Kit C-4171 - Driver Handle, Universal (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202CC, 9299, 9299CC, 9299CC, 9300A-CAN.) C-823 - Hone, Cylinder

Scheme 246

Scheme 247

Scheme 248

Scheme 249

Scheme 250

Scheme 251

Scheme 252

Scheme 253

Scheme 254

Scheme 255

Scheme 256

Scheme 257

Scheme 258

Scheme 259

1. Loosen clamp (1) and disconnect air duct (2) at air cleaner cover (3).
2. Pry over 4 spring clips (5) from housing cover (3).
3. Release housing cover (3) from locating tabs on housing and remove cover.
4. Remove air cleaner element (filter) from housing.
5. Clean inside of housing before replacing element.