Timing, Adjust
| .D. ICON01.tif | 0,75 | 0,75 | tiff;; Remove, Disconnect |
Ignition cable cover from cylinder head cover.
| Spark plug connectors - use accompanying tool (1). | |||
|---|---|---|---|
| .P. E5152.tif | 9 | 7,5 | tiff;; |
| .D. ICON01.tif | 0,75 | 0,75 | tiff;; Remove, Disconnect |
Crankcase ventilation hoses (1) and (2) from cylinder head cover.
Harness connector from camshaft sensor.
| Cylinder head cover from cylinder head - note seal rings. | |||
|---|---|---|---|
| .P. E5165.tif | 9 | 7,5 | tiff;; |
| .D. ICON01.tif | 0,75 | 0,75 | tiff;; Remove, Disconnect |
Skid plate.
| Torsional vibration damper - counterhold on fastening bolt of toothed belt drive gear. | |||
|---|---|---|---|
| .P. E5166.tif | 9 | 7,5 | tiff;; |
| .D. ICON08.tif | 0,75 | 0,75 | tiff;; Adjust |
| Loosen fastening bolt for toothed belt tension roller and turn adjustment eccentric in direction of arrow (clockwise) until pointer (1) is at left stop. | |||
| .P. E3577.tif | 9 | 7,5 | tiff;; |
| .D. ICON08.tif | 0,75 | 0,75 | tiff;; Adjust |
Remove toothed belt from camshaft gears.
| At hex of camshaft, turn camshaft gear (short way) to mark - lug (1) on guide bearing aligns with notch (2) on camshaft gear. | |||
|---|---|---|---|
| .P. E5271.tif | 9 | 7,5 | tiff;; |
| .D. ICON02.tif | 0,75 | 0,75 | tiff;; Install, Connect |
Toothed belt - ensure that tensioned side (I) is taut.
Note timing marks.
| Adjust toothed belt tension - see operation 'Toothed Belt Tension, Check and Adjust'. | |||
|---|---|---|---|
| .P. E5167.tif | 9 | 7,5 | tiff;; |
| .D. ICON02.tif | 0,75 | 0,75 | tiff;; Install, Connect |
Torsional vibration damper - counterhold on fastening bolt of toothed belt drive gear.
Torsional vibration damper to toothed belt drive gear.
Skid plate.
| .D. ICON09.tif | 0,75 | 0,75 | tiff;; Tighten (Torque) |
Damper to toothed belt drive gear - 20 Nm / 15 lbf ft.
| Skid plate bolts - 57 Nm / 42 lbf ft. | |||
|---|---|---|---|
| .P. E5166.tif | 9 | 7,5 | tiff;; |
| .D. ICON02.tif | 0,75 | 0,75 | tiff;; Install, Connect |
Cylinder head cover - note seal rings.
Cylinder head cover to cylinder head.
Crankcase ventilation hoses to cylinder head cover.
| .D. ICON09.tif | 0,75 | 0,75 | tiff;; Tighten (Torque) |
|---|---|---|---|
| Cylinder cover - 8 Nm / 6 lbf ft. | |||
| .P. E5168.tif | 9 | 7,5 | tiff;; |
| .D. ICON02.tif | 0,75 | 0,75 | tiff;; Install, Connect |
Spark plug connectors.
Harness connector (1) to camshaft sensor.
Ignition cable cover to cylinder head cover.
| .D. ICON09.tif | 0,75 | 0,75 | tiff;; Tighten (Torque) |
|---|---|---|---|
| Ignition cable cover - 3 Nm / 2 lbf ft. | |||
| .P. E5398.tif | 9 | 7,5 | tiff;; |
| .D. ICON02.tif | 0,75 | 0,75 | tiff;; Install, Connect |
Toothed belt front cover to rear toothed belt cover.
Ribbed V - belt - tension ribbed V - belt with ribbed V - belt tension roller.
Note running direction of ribbed V - belt.
| Ground cable to battery. | |||
|---|---|---|---|
| .P. U8093.tif | 9 | 7,5 | tiff;; |