A brief survey of engine and transmission availability for all Movano models in MY 2004 is given in the table below.
| Engine | Transmission |
|---|---|
| F9Q 774 | PK5 |
| G9T 750 | |
| G9U 750 | PK6 |
| G9U 754 | PK5 |
| PK6 |
Transmission
PK5 = 5 speed manual
PK6 = 6 speed manual
Home/Opel/Movano/Opel Movano A (1999-2011)/Repair manual/Diesel Engine/Engine and Transmission Availability
Contents
Wiring diagrams Section: Diesel Engine- Power Take-Off, F9Q 772
- Battery / Starter, Diesel (Current Measurement)
- Battery / Starter (Voltage Measurement)
- Compression 4-cylinder, Diesel
- Air Flow Restriction Indicator
- Engines Introduction
- Torque and Power Curves
- Survey of Engine Characteristic Data
- F9Q 774 Engine Survey
- Views of F9Q 774 Engine
- Diesel Glow Plugs (Current Measurement), 4 Cylinder
- Measuring Oil Consumption
- Engine and Transmission Availability
- Service Plan
- Engine Ventilation Oil Separator – Remove and Install
- Service Programmable System (Sps)
- Camshaft Sensor, F9Q, Y26SE, Y32SE, Z32SE, ZD3
- Air Mass Meter, F9Q, G9T, G9U
- Injector, Common Rail Diesel, G9T, G9U
- Exhaust Gas Recirculation Valve, G9T
- Injector, Common Rail Diesel, F9Q and Y25DT
- Crankshaft Impulse Sensor, F4R, F9Q, G9T
- Introduction
- Exhaust Gas Recirculation Valve, F9Q
- General Engine and Engine Attaching Parts
- Engine Identification S8U and S9W
- Survey of Engines S8U and S9W
- Location of Engine Number S8U and S9W
- Torque and Output Curves S8U
- Torque and Output Curves, S9W
- OHC Diesel Engine S8U
- Intake Tract S8U
- OHC Turbodiesel Engine S9W
- Intake Tract S9W
- Cylinder Head Valves Camshaft and Cam Followers S9W
- Pistons S9W
- Oil Circuit S8U and S9W
- Oil Cooler S8U and S9W
- Engine/transmission Damping Blocks and Brackets S8U and S9W
- General Inspection System
- Movano Inspection System
- Engine - Engine Attaching Parts Special Service Tools
- Engine Number (S9W 700 and 702)
- Compression Check (S9W 700 and 702)
- How to Check (S9W 700 and 702) the Engine Pressure Loss
- How to Measure (S9W 700 and 702) the Fuel Consumption
- How to Check and Adjust (S9W 700 and 702) the Valve Clearance
- How to Check (S9W 700 and 702) the Timing
- How to Remove and Install the Timing Belt Covers (Without Air Conditioning (S9W))
- How to Replace the Timing Belt (Without Air Conditioning (S9W 700 and 702))
- How to Replace (S9W 700 and 702) the Gaskets Intake Manifold to Cylinder Head
- How to Replace the Gaskets, Exhaust Manifold to Cylinder Head
- How to Replace (S9W 700 and 702) the Gasket, Cylinder Head Cover
- How to Remove and Install (S9W 700 and 702) the Valve Springs
- How to Replace (S9W 700 and 702) the Valve Stem Oil Seals
- How to Remove and Install (S9W 700 and 702) the Cylinder Head
- Cylinder Head, Disassemble and Assemble
- How to Check for Plane Surface (S9W 700 and 702) the Cylinder Head
- How to Check (S9W 700 and 702) the Valve Depth Below Cylinder Head
- Valve Seat, Cut (S9W 700 and 702)
- Valve, Grind-In (S9W 700 and 702)
- How to Check (S9W 700 and 702) the Valve Stem Protrusion
- How to Remove and Install (S9W 700 and 702) the Camshaft and Cam Followers
- How to Check (S9W 700 and 702) the Camshaft and Cam Followers
- How to Replace (S9W 700 and 702) the Camshaft Bearings
- How to Replace (S9W 700 and 702) the Camshaft Oil Seal
- How to Remove and Install (S9W 700 and 702) the Flywheel
- How to Replace (S9W 700 and 702) the Pilot Bearing, Crankshaft
- How to Check (S9W 700 and 702) the Flywheel
- How to Remove and Install (S9W 700 and 702) the Piston with Con-Rod
- How to Remove and Install (S9W 700 and 702) the Piston Rings
- How to Replace (S9W 700 and 702) the Con-Rod Bearing
- How to Check and Replace (S9W 700 and 702) the Con-Rod or Piston
- How to Replace (S9W 700 and 702) the Con-Rod Bushing
- How to Remove and Install (S9W 700 and 702) the Crankshaft
- How to Check (S9W 700 and 702) the Crankshaft Axial Play
- How to Replace (S9W 700 and 702) the Crankshaft Oil Seal, Front
- How to Replace (S9W 700 and 702) the Crankshaft Oil Seal Assembly, Rear
- How to Remove and Install (S9W 700 and 702) the Ancillary Drive Unit
- How to Remove and Install (S9W 700 and 702) the Ancillary Drive Gear
- How to Replace (S9W 700 and 702) the Front Cover Oil Seal, Ancillary Drive Unit
- How to Replace (S9W 700 and 702) the Gasket, Front Cover to Ancillary Drive Unit
- How to Remove and Install (S9W 700 and 702) the Vacuum Pump
- How to Check (S9W 700 and 702) the Vacuum Pump
- How to Replace (S9W 700 and 702) the Oil Filter Cartridge
- How to Replace (S9W 700 and 702) the Gasket, Oil Pan
- How to Remove and Install (S9W 700 and 702) the Oil Pick-Up and Filter
- How to Remove and Install (S9W 700 and 702) the Sensor, Minimum Oil Capacity
- How to Check (S9W 700 and 702) the Oil Pump
- How to Replace (S9W 700 and 702) the Oil Pump Pressure Relief Valve
- How to Replace (S9W 700 the Engine Damping Block, Right (S9W 702))
- How to Replace (S9W 700 the Engine Damping Block, Left (S9W 702))
- How to Replace (S9W 700 and 702) the Damping Block, Rear Torque Stabilizer
- How to Remove and Install (S9W Without Air Conditioning) the Engine with Transmission
- How to Check (S9W 700 and 702) the Cylinder Liner
- How to Replace (S9W 700 and 702) the Cylinder Liner
- How to Check for Plane Surface (S9W 700 and 702) the Cylinder Block
- Special Service Tools (S9W 700, S9W 702)
- Technical Data (Group J)
- Engine Number – S8U 772
- How to Check and Adjust (S8U 772) the Ribbed V-Belt, Tension
- How to Check (S8U 772) the Compression
- How to Check (S8U 772) the Engine Pressure Loss
- How to Measure the Fuel Consumption (S8U)
- How to Check and Adjust the Valve Clearance (S8U)
- How to Check the Timing (S8U)
- How to Remove and Install the Timing Belt Covers (S8U)
- How to Remove and Install the Timing Belt (S8U)
- How to Replace the Gaskets, Intake Manifold to Cylinder Head (S8U)
- How to Replace the Gaskets, Exhaust Manifold to Cylinder Head (S8U)
- How to Replace the Gasket, Cylinder Head Cover (S8U)
- How to Remove and Install the Valve Springs (S8U)
- Coolant Temperature Gauge in Red Zone, Warning Lamp Illuminates
- How to Replace the Valve Stem Oil Seals (S8U)
- How to Remove and Install the Cylinder Head (S8U)
- How to Overhaul the Cylinder Head (S8U)
- How to Check and Replace the Swirl Chamber (S8U)
- How to Check for Plane Surface the Cylinder Head (S8U)
- How to Replace the Valve Guide (S8U)
- How to Check the Valve Depth Below Cylinder Head (S8U)
- Valve Seat, Cut (S8U)
- Valve, Grind-In (S8U)
- How to Check the Valve Stem Protrusion (S8U)
- How to Remove and Install the Camshaft and Cam Followers (S8U)
- How to Check the Camshaft and Cam Followers (S8U)
- How to Replace the Camshaft Bearings (S8U)
- How to Replace the Camshaft Oil Seal (S8U)
- How to Remove and Install (S8U 772) the Flywheel
- How to Replace (S8U 772) the Pilot Bearing, Crankshaft
- How to Check (S8U 772) the Flywheel
- How to Remove and Install the Piston with Con-Rod (S8U)
- How to Remove and Install the Piston Rings (S8U)
- How to Replace the Con-Rod Bearing (S8U)
- How to Check and Replace the Con-Rod or Piston (S8U)
- How to Replace the Con-Rod Bushing (S8U)
- How to Remove and Install the Crankshaft (S8U)
- How to Check the Crankshaft, Axial Play (S8U)
- How to Replace the Crankshaft Oil Seal Assembly, Front (S8U)
- How to Replace the Crankshaft Oil Seal Assembly, Rear (S8U)
- How to Remove and Install (S8U 772) the Ancillary Drive Unit
- How to Remove and Install (S8U 772) the Ancillary Drive Gear
- How to Replace the Front Cover Oil Seal, Ancillary Drive Unit (S8U)
- How to Remove and Install the Gasket, Front Cover to Ancillary Drive Unit (S8U)
- How to Remove and Install the Vacuum Pump (S8U)
- How to Check the Vacuum Pump (S8U)
- How to Replace (S8U 772) the Oil Filter Cartridge
- How to Replace the Gasket, Oil Pan (S8U)
- How to Remove and Install the Oil Pick-Up and Filter (S8U)
- How to Remove and Install the Sensor, Minimum Oil Capacity (S8U)
- How to Replace the Oil Pressure Switch (S8U)
- How to Check the Oil Pump (S8U)
- How to Replace the Oil Pressure Relief Valve (S8U)
- How to Replace (S8U 772) the Ribbed V-Belt
- How to Replace the Engine Damping Block, Right (S8U)
- How to Replace the Engine Damping Block, Left (S8U)
- How to Replace the Rear Torque Stabilizer, Damping Block (S8U)
- How to Remove and Install the Engine with Transmission (S8U)
- How to Check the Cylinder Liner (S8U)
- How to Replace the Cylinder Liner (S8U)
- How to Check for Plane Surface the Cylinder Block (S8U)
- Special Service Tools (Group J S8U 772)
- Toothed Belt Diagnosis - Possible Causes and Remedys
- How to Check (Plastigage Method) the Crankshaft Bearing Clearance (S8U)
- How to Check (Micrometer Method) the Crankshaft Bearing Clearance (S8U)
- Recommended Torque Values (Group J)
- How to Check the Crankshaft Bearing Clearance (Plastigage Method (S9W 700 and 702))
- How to Check the Crankshaft Bearing Clearance (Micrometer Method (S9W 700 and 702))
- Toothbelt - Service Intervall Overview
- How to Check and Adjust (S9W 700 and 702) the Actuator, Wastegate
- Engine Number (F9Q 770)
- Fuel Consumption Measure (F9Q 770)
- How to Check and Adjust (F9Q 770) the Valve Clearance
- How to Check (F9Q 770) the Timing
- How to Remove and Install the Timing Belt Covers
- How to Replace the Gaskets, Intake/exhaust Manifold to Cylinder Head
- How to Replace the Gasket, Cylinder Head Cover
- How to Remove and Install the Valve Springs
- How to Replace the Valve Stem Oil Seal
- How to Remove and Install the Cylinder Head
- How to Overhaul the Cylinder Head
- Valve Seat, Cut
- Valve Grind-In
- How to Remove and Install the Camshaft and Cam Followers
- How to Check the Camshaft and Cam Followers
- How to Replace the Camshaft Oil Seal
- How to Remove and Install the Flywheel
- How to Replace (F9Q 770) the Crankshaft Pilot Bearing
- How to Check (F9Q 770) the Flywheel
- How to Remove and Install (F9Q 770) the Piston with Con-Rod
- How to Remove and Install (F9Q 770) the Piston Rings
- How to Replace (F9Q 770) the Con-Rod Bearings
- How to Check and Replace (F9Q 770) the Con-Rod or Piston
- How to Remove and Install the Crankshaft
- How to Check the Crankshaft, Axial Play
- How to Check (Measure with Plastigage Method) (F9Q 770) the Crankshaft, Bearing Clearance
- How to Check (Measure with Micrometer Method) (F9Q 770) the Crankshaft, Bearing Clearance
- How to Replace (F9Q 770) the Crankshaft Front Oil Seal
- How to Replace (F9Q 770) the Crankshaft Rear Oil Seal
- How to Remove and Install the Vacuum Pump