Recommended Torque Values
Nm
Alternator bracket to cylinder block 35
Alternator lower fastening block to alternator bracket 35
Auxiliary aggregate support to cylinder block 35
Bearing bridge and baffle plate to cylinder block 20
Brake servo vacuum line to intake manifold 20
Camshaft gear to camshaft 45
Camshaft housing cover to camshaft housing 8
Compressor bracket to cylinder block and auxiliary aggregate support 35
Con - rod bearing cover to con - rod 35 + 45° + 15° 4)
Coolant temperature sender to hose 11
Coolant temperature sensor to thermostat housing 10
Crankcase ventilation flange to cylinder block 25
Crankshaft bearing cover to cylinder block 50 + 45° + 15° 4)
Crankshaft pulse pick - up in cylinder block 6
Crankshaft pulse pick - up sensor disc to crankshaft 13
Cylinder head to cylinder block 25 + 90° + 90° + 90° 4)8)
Drive disc to crankshaft 60 1)
Dual - mass flywheel to crankshaft 65 + 30° + 15° 4)7)
Engine bracket to cylinder block 60
Engine front damping block to engine bracket 85
Engine front damping block to chassis 50
Engine rear damping block to transmission 80
Engine rear damping block to crossmember 50
Engine support to transmission and cylinder block 40
Engine transport shackle to camshaft housing 15
Exhaust manifold 22 2)
Flywheel to crankshaft 65 + 30° + 15° 4)4)7
Front exhaust pipe with catalytic converter to exhaust manifold and mufflers 25
Front fastening bolts to compressor to auxiliary aggregate support 35
Front toothed belt cover to rear toothed belt cover 4
Fuel distribution pipe to intake manifold 8
Ground cable to cylinder block 20
Heat sleeves in cylinder head 30 3)
Heat shield to exhaust manifold 9
Intake manifold to cylinder head 22
Knock sensor to cylinder block 20
Oil cooler lines to radiator 25
Oil drain bolt to oil pan 55
Oil filter to oil pump 15
Oil intake pipe bracket to cylinder block 6
Oil intake pipe to oil pump 8 1)6)
Oil pan to oil pump and cylinder block (up to MY 97) 15 1)6)
Oil pan to oil pump and cylinder block (as of MY 97) 20
Oil pressure switch to oil pump 40
Oil pump cover to oil pump 6
Oil pump to cylinder block 6
Oxygen sensor to front exhaust pipe 30 5)
Power steering pump shackle to support 20
Power steering pump to auxiliary aggregate support 25
Rear fastening bolts to compressor bracket 18
Ribbed V - belt tension roller to auxiliary aggregate support 18
Safety valve to oil pump 30
Shackle to intake manifold and alternator 18
Skid plate bolts 57
Spark plug to cylinder head 25
Starter bracket to cylinder block 25
Starter to cylinder block 60
Support to intake manifold and alternator 18
Thermostat housing to cylinder head 15
Toothed belt drive gear to crankshaft 30 + 40° to 50° 4)
Toothed belt rear cover to oil pump and camshaft housing 6
Toothed belt tension roller to oil pump 25
Torsion vibration damper to toothed belt drive gear 20
Water pump to cylinder block 25
Wiring trough to camshaft housing 8
Wiring trough to front toothed belt cover 4
1) Recut bolts before reuse and insert with Locking Compound 15 10 177 (90 167 347)
2) Use new nuts
3) Insert with Molycote Paste 19 48 525 (90 513 211)
4) Use new bolt(s)
5) Insert with Special Grease 19 48 602 (5 613 695)
6) Maximum installation time including torque check is 10 min.
7) Maximum installation time including torque check is 5 min.
8) No retightening required