RADIO AND CD PLAYER ERROR CODES
If the radio and CD player detects any malfunction in itself or the inserted CD, the error codes below will be shown on the display.
| Error code | Cause | Cause of trouble and its solution |
|---|---|---|
| ERROR | Power supply error | This error code will be shown if there is any problem in the power supply system of the radio and CD player. Check the connectors and wiring harness of the power supply system, and check that the battery voltage is normal. Check that the same error does not appear. |
| ERROR 01 | Focus error | These error codes will be shown if there is any problem with the CD or there is excessive vibration on the vehicle. If the error codes are not displayed when the vehicle is stopped and another CD is inserted, there is a problem with the CD. Check if there is any of the following problems with the CD. Contamination, scratch, or deformation Formation of moisture or grease Repair the CD and insert it again. Then, check that no error appears. |
| ERROR 02 | Abnormal disk | |
| ERROR 03 | Mechanical error | This error codes will be shown if there is any internal mechanical or electrical problem in the radio and CD player. Replace the radio and CD player check that no error codes are shown. |
| ERROR HOT | Protection against high temperature | If the internal temperature is extremely high, this error code will be shown. Turn off the radio and CD player and wait until they cool down. Wait for a while, and then turn on the unit again. Check that the same error does not appear. |
| ERROR DC | Detection abnormal output to the speaker | This error code will be shown if the radio and CD player or the audio amplifier has an internal error or is contaminated with the foreign material, and there is a problem with output to the speaker. If it is contaminated with the foreign material, turn OFF the power. Dry the foreign material if it is liquid, and remove it if it is solid. Then, check if the error code is displayed. If the error code is displayed, replace the radio and CD player or the audio amplifier. |
| I NO SONG | No playable music file is found. | No playable music file is stored in the iPod. Store music files to the iPod. |
| I VER ERROR | IPod cannot be recognized | IPod itself or software is not supported. Use the supported iPod. |
| I CONNECT i RETRY | IPod cannot be authenticated. | IPod is not authenticated. Reconnect. If the error code is not erased after that, the USB box communication may have a problem. Carry out the troubleshooting of "The USB adapter data cannot be replayed". Refer to SYMPTOM PROCEDURES . |
| U NO SONG | No playable music file is found. | No playable music file is stored in the USB memory. Store music files to the USB memory. |
| U FILE ERROR | Playback of unplayable file (copyright protected file, etc.) is attempted. | Displayed when the playback of unplayable file such as a copyright protected file is attempted. The error code is displayed approximately for 3 seconds, and then a next playable file is played automatically. |
| UNSUPPORTED DEVICE | Unsupported device | The USB memory is not supported by the USB box. Use the supported USB memory. |
| UNSUPPORTED FORMAT | Unsupported format | The USB memory is not supported by the USB box. Use the supported USB memory. |
| USB BUS PWR | Overcurrent abnormality | There is a communication error with the USB box. Carry out the troubleshooting of "The USB adapter data cannot be replayed". (Refer to SYMPTOM PROCEDURES . |
| U CONNECT U RETRY | USB memory cannot be authenticated. | The USB memory is not authenticated. Reconnect. If the error code is not erased after that, the USB box communication may have a problem. Carry out the troubleshooting of "The USB adapter data cannot be replayed". Refer to SYMPTOM PROCEDURES . |
| U LSI ERROR | USB box internal error | This error code will be shown when there is a problem in the USB box. Replace the USB box. |
RADIO AND CD PLAYER ERROR CODES REFERENCE CHART
SATELLITE RADIO ERROR CODES
The display displays the error codes below if an abnormality related to the satellite radio is detected.
| Error code | Cause | Cause of trouble and its solution |
|---|---|---|
| ANTENNA ERROR | Antenna error | This code is displayed when there is a failure, improper connection, or open circuit in the satellite antenna base and the satellite radio tuner cannot receive normal voltage value or current value. Check the satellite radio tuner, the satellite antenna base and the antenna feeder cable, and replace if necessary. (Refer to TROUBLE SYMPTOM CHART ). |
| ACQUIRING SIGNAL | Cannot pick up signal | This code is displayed when the signal is too weak and it cannot be received. Move to a place where the signal can be received easily, or check if there is foreign material that interferes with signal reception on the satellite antenna base, and remove if necessary. |
| CALL 888-539-SIRIUS | Unauthorized channel | This code is displayed when the channel to be received is not included in the contract with SIRIUS™ satellite radio. Contact SIRIUS™ satellite radio and make a contract for the channel. |
| NO CHANNEL | There is no selectable channel | There is no channel that can be selected. Cancel the SKIP settings so that the channels can be selected. |
| INVALID CHANNEL | Channel is invalid | No program is broadcast on this channel now, or this channel cannot be received. Ask SIRIUS™ satellite radio. |
| SAT ERROR | Mechanical fault or bad connection | This code is displayed when the satellite radio tuner has a mechanical problem or when an error occurs in the communication with radio and CD player. Check the radio and CD player, the satellite radio tuner, and each harness and connector, and replace if necessary. (Refer to TROUBLE SYMPTOM CHART ). |
| OFF AIR | OFF AIR | This code is displayed when this channel is not broadcast at this moment, or broadcast of the satellite radio is interrupted. Check the airtime and the broadcast conditions of SIRIUS™ satellite radio. |
| NOT ACTIVATED | ID not registered | This code is displayed when the SIRIUS ID is not written to the satellite radio tuner. Replace the satellite radio tuner. |
| READING | Data reading in progress | This code is displayed when the data received is being read. Wait until reading of the data received is completed. |
| UPDATING | Channel data updating in progress | This code is displayed when SIRIUS™ satellite radio is updating the channel data. Wait until update is completed. |
| SUB UPDATING PRESS ANY KEY | Contract status updating complete | This code is displayed when the contract status is updated. This code disappears when any of the audio switch is pressed. |
SATELLITE RADIO ERROR CODES REFERENCE CHART
CHECK OF FREEZE FRAME DATA
The freeze frame data can be checked by using scan tool MB991958.
When detecting fault and storing the diagnostic trouble code, the ECU connected to CAN bus line obtains the data before the determination of the diagnostic trouble code and the data when the diagnostic trouble code is determined, and then stores the ECU status of that time. By analyzing each data from scan tool MB991958, the troubleshooting can be performed more efficiently. The displayed items are as the table below.
Display item list
| Item No. | Item name | Data item | Unit |
|---|---|---|---|
| 1 | Odometer | Total driving distance after the diagnostic trouble code is generated | Mile |
| 2 | Ignition cycle | Number of times the ignition switch is turned "ON" or "LOCK (OFF)" after the past failure transition | Number of counts is displayed. |
| 4 | Accumulated minute | Cumulative time for current malfunction of diagnostic trouble code | Min |
DISPLAY ITEM LIST
PROBABLE CAUSES
- Malfunctions of radio and CD player
- Malfunction of CAN bus line wiring harness and connector
JUDGEMENT CRITERIA
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communication with ETACS-ECU cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system voltage between 10-16 volts (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communication with SRS-ECU cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communications with occupant classification-ECU cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communications with combination meter cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
With the ignition switch in the ON position, system voltage between 10-16 volts (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communication with A/C-ECU cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
With the ignition switch in the ON position, system voltage between 10 - 16 V (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communication with KOS-ECU or WCM cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse (IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communications with satellite radio tuner cannot be established for 2, 500 ms or more, the radio and CD player determines that a problem has occurred.
- The CAN bus line may be defective.
- The radio and CD player may be defective.
- The radio and CD player may be defective
- The ETACS-ECU may be defective
- Option coding information inconsistency
- Damaged harness wires and connectors
- The radio and CD player may be defective
- The audio amplifier may be defective
- Option coding information inconsistency
- Damaged harness wires and connectors
- The speaker may be defective
- The radio and CD player may be defective
- Damaged harness wires and connectors
- The speaker may be defective
- The radio and CD player may be defective
- The audio amplifier may be defective
- Option coding information inconsistency
- Damaged harness wires and connectors
- The radio and CD player may be defective.
- The center panel unit may be defective.
- Damaged harness wires and connectors
- The combination meter may be defective.
- The radio and CD player may be defective.
- The center panel unit may be defective.
- Damaged harness wires and connectors
- The audio adapter may be defective.
- The radio and CD player may be defective.
- Damaged harness wires and connectors
- Damaged wiring harness or connector
- Malfunction of the radio and CD player
SERVICE DATA
| Item No. | Scan tool display | Check condition | Normal condition |
|---|---|---|---|
| 1 | RADIO remoto SW (SEEK-) | When the "CH down" switch is pushed | ON |
| 2 | RADIO remoto SW (SEEK+) | When the "CH up" switch is pushed | ON |
| 3 | RADIO remoto SW (MODE) | When the "Mode" switch is pushed | ON |
| 4 | RADIO remoto SW (VOL-) | When the "VOL down" switch is pushed | ON |
| 5 | RADIO remoto SW (VOL+) | When the "VOL up" switch is pushed | ON |
| 10 | On hook switch | When the "Hang-up" switch is pushed | ON |
| 11 | Off hook switch | When the "Pick-up" switch is pushed | ON |
| 13 | VR switch | When the "Speech" switch is pushed | ON |
SERVICE DATA REFERENCE CHART