Home ReviewsRefund
Home/Mazda/Tribute/Mazda Tribute II (2007-2011)/Repair manual/Automatic Trans/Technical Data (Transaxle) - Tribute Except Hybrid: Specifi…
Contents Wiring diagrams Section: Automatic Trans All sections

Technical Data (Transaxle) - Tribute Except Hybrid: Specifications Mazda Tribute II

Automatic Trans

General Specifications

ItemSpecification
Fill Capacity8.5L (9 qt)
Multi-Purpose GreaseXG-4 and/or XL-5 ESB-M1C93-B
Thread Sealant with PTFE TA-24WSK-M2G350-A2
Transaxle weight86 kg (189 1b)
Fluid
Automatic Transaxle/Power Steering Dye164-R3701 or equivalent
MERCON® V Automatic Transaxle FluidXT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V

GENERAL SPECIFICATIONS CHART

CAUTIONAutomatic transmission fluids are not interchangeable. The use of any fluid other than what is recommended for this transaxle will cause transaxle damage. Refer to the information under SPECIFICATION for the correct fluid. This transaxle is a fill for life and the transmission fluid should be changed every 241,402 km (150,000 mi) regardless of normal or special operating conditions.
CAUTIONDo not use water-based cleaners to clean or flush the cooler tubes or transmission damage will occur. Mineral spirits can be used to clean the cooler tubes, providing the cooler tubes are flushed with clean automatic transmission fluid and blown dry with shop air. Use only clean automatic transmission fluid designated for the transmission and torque converter being serviced.
Differential
Preload0.15-0.21 mm (0.0059-0.0083 in)
Adjustment shim thicknessSee TRANSAXLE ASSEMBLY for adjustment shim selection procedure.
Side gear and pinion gear backlash0.02-0.08 mm (0.0079-0.0031 in)
Gear Clearance
1st gear end play0.20-0.30 mm (0.0078-0.0118 in)
2nd gear end play0.06-0.16 mm (0.0024-0.0063 in)
3rd gear thrust clearance0.18-0.31 mm (0.0071-0.0122 in)
4th gear end play0.20-0.30 mm (0.0078-0.0118 in)
5th gear thrust clearance0.06-0.16 mm (0.0024-0.0063 in)
Input Shaft
End play0.00-0.06 mm (0.00-0.0024 in)
Adjustment shim thicknessSee TRANSAXLE ASSEMBLY for shim selection procedure.
Main Shaft
End play0.00-0.06 mm (0.00-0.0024 in)
Adjustment shim thicknessSee TRANSAXLE ASSEMBLY for shim selection procedure.
Reverse idler gear
End play0.04-0.14 mm (0.0016-0.0055 in)
Adjustment shim thicknessSee TRANSAXLE ASSEMBLY for shim selection procedure.
Input shaft thrust washer thicknessSee INPUT SHAFT DISASSEMBLY/ASSEMBLY for thrust washer thickness chart.
Input shaft snap ring thicknessSee INPUT SHAFT DISASSEMBLY/ASSEMBLY for snap ring thickness chart.
4th gear adjustment shim thicknessSee OUTPUT SHAFT DISASSEMBLY/ASSEMBLY for 4th gear adjustment shim thickness chart.
5th gear snap ring thicknessSee OUTPUT SHAFT DISASSEMBLY/ASSEMBLY for 5th gear snap ring thickness chart.
Mainshaft C-ring thicknessSee OUTPUT SHAFT DISASSEMBLY/ASSEMBLY for C-ring thickness chart.
Synchronizer ring clearance
1st gear clearance (outer ring-to-synchronizer cone)0.60-1.10 mm (0.0236-0.0433 in)
1st gear clearance (inner ring-to-synchronizer cone)0.60-0.80 mm (0.0236-0.0314 in)
Differential
2nd gear clearance (middle synchronizer ring-to-gear)0.60-1.20 mm (0.0236-0.0472 in)
2nd gear clearance (outer ring-to-synchronizer cone)0.60-1.10 mm (0.0236-0.0433 in)
2nd gear clearance (inner ring-to-gear)0.70-1.10 mm (0.0276-0.0433 in)
3rd gear0.90-1.45 mm (0.0354-0.0571 in)
4th gear0.90-1.45 mm (0.0354-0.0571 in)
5th gear0.95-1.40 mm (0.0374-0.0551 in)
Reverse idler gear0.95-1.40 mm (0.0374-0.0551 in)
Clutch Disc
Minimum allowable depth to rivet head0.3 mm (0.012 in)
Maximum runout0.7 mm (0.027 in)
Clutch Pressure Plate
Maximum runout0.5 mm (0.02 in)
Flywheel Runout
Maximum runout0.200 mm (0.008 in)
Pressure Plate Diaphragm Spring Fingers
Maximum depth0.5 mm (0.020 in)
Maximum clearance0.5 mm (0.020 in)
Clutch pedal free play5.0-13.0 mm (0.20-0.51 in)
Transaxle
Physical weight

GENERAL SPECIFICATIONS CHART

More articles — Technical Data (Transaxle) - Tribute Except Hybrid