Home/Honda/CR-V/Honda CR-V II (2001-2004)/Repair manual/Testing & Diagnostics/DTC P1106: BARO Sensor Range/ Performance Problem, DTC P222…

Contents

Wiring diagrams Section: Testing & Diagnostics

Pgm-Fi System: Overview
Pgm-Fi System: Diagnosis
DTC P1128: MAP Sensor Signal Lower Than Expected
DTC P1129: MAP Sensor Signal Higher Than Expected
DTC P0116: ECT Sensor Range/Performance Problem
DTC P1121: TP Sensor Signal Lower Than Expected
DTC P1122: TP Sensor Signal Higher Than Expected
DTC P0125: ECT Sensor Malfunction/Slow Response
DTC P0128: Cooling System Malfunction
DTC P0134: A/F Sensor (Sensor 1) Signal Stuck Lean
DTC P0139: Secondary HO2S (Sensor 2) Slow Response
DTC P0172: Fuel System Too Rich
DTC P0300: Random Misfire Detected and Any Combination of the Following: DTC P0301: No. 1 Cylinder Misfire Detected, DTC P0302: No. 2 Cylinder Misfire Detected, DTC P0303: No. 3 Cylinder Misfire Detected, DTC P0304: No. 4 Cylinder Misfire Detected
DTC P0335: CKP Sensor No Signal, DTC P0336: CKP Sensor Intermittent Interruption, DTC P0339: CKP Sensor Intermittent Interruption
DTC P1106: BARO Sensor Range/ Performance Problem, DTC P2227: BARO Sensor Range/ Performance Problem*
DTC P1107: BARO Sensor Circuit Low Voltage, DTC P1108: BARO Sensor Circuit High Voltage, DTC P2228: BARO Sensor Circuit Low Voltage*, DTC P2229: BARO Sensor Circuit High Voltage*
DTC P1158: A/F Sensor (Sensor 1) AFS-Terminal Low Voltage, DTC P2252: A/F Sensor (Sensor 1) AFS-Terminal Low Voltage*
DTC P1159: A/F Sensor (Sensor 1) AFS + Terminal Low Voltage, DTC P2238: A/F Sensor (Sensor 1) AFS + Terminal Low Voltage*
DTC P0133: A/F Sensor (Sensor 1) Slow Response*, DTC P1163: A/F Sensor (Sensor 1) Slow Response
DTC P1164: A/F Sensor (Sensor 1) Circuit Range/Performance Problem, DTC P2A00: A/F Sensor (Sensor 1)* Range/ Performance Problem*
DTC P0135: A/F Sensor (Sensor 1) Heater Circuit Malfunction*, DTC P1166: A/F Sensor (Sensor 1) Heater Circuit Malfunction
DTC P0365: CMP Sensor B No Signal*, DTC P0369: CMP Sensor B Intermittent Interruption*, DTC P1361: CMP Sensor B (TDC Sensor) Intermittent Interruption, DTC P1362: CMP Sensor B (TDC Sensor) No Signal*
DTC P0607: Malfunction in ECM/PCM Internal Circuit*, DTC P1607: Malfunction in ECM/PCM Internal Circuit
Pgm-Fi System: Removal & Installation

All sections

DTC P1106: BARO Sensor Range/ Performance Problem, DTC P2227: BARO Sensor Range/ Performance Problem* Honda CR-V II

Testing & Diagnostics ~152 words

Note. Information marked with an asterisk (*) applies to '04 model.

Reset the ECM/PCM (see «HOW TO RESET THE ECM/PCM»(ref-171385-S07999163522005020300000) ).
Start the engine. Hold the engine at 3,000 RPM with no load (in Park or neutral) until the radiator fan comes on, then let it idle.
Test-drive with the A/T in 2 position, or the M/T in 4th gear.
Accelerate for 5 seconds using wide open throttle.
Check for a Temporary DTC with the scan tool or the HDS. Is Temporary DTC P1106 (P2227)* indicated? YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/ PCM, then recheck (see «ECM/PCM UPDATING AND SUBSTITUTION FOR TESTING»(ref-171385-S32387647222005020300000) ). If the symptom/ indication goes away with a known-good ECM/PCM, replace the original ECM/PCM. NO -Intermittent failure, system is OK at this time.