Repair manual
Wiring diagrams
Honda CR-V II Repair Manual
Step-by-step repair and maintenance instructions for the Honda CR-V II (2001–2004): removal, installation, adjustment, diagnostics and parameter checks with illustrations.
80sections
582articles
ENManual language
- Automatic Transmission Diagnosis - Mcva & Mrva 30
- Automatic Transmission Overhaul - Mcva & Mrva 8
- Shift Interlock Systems 4
- Automatic Transmission Removal & Installation
- Automatic Transmission Diagnosis - Mcva (2WD) & Mrva (4WD) 24
- Automatic Transmission Servicing 3
- Automatic Transmission Interlock System 2
- Automatic Transmission Overhaul - Mcva (2WD) & Mrva (4WD) 4
- How to Check for DTCs with the SCS Mode (retrieving the flash codes)
- How to Substitute the PCM
- Electronic Control
- Hydraulic Control
- Shift Control Mechanism
- Lock-up Mechanism
- Gear Selection
- Automatic Transaxle (A/T) Gear Position Indicator
- Transfer Mechanism (4WD)
- Clutches
- 1st Clutch
- 2nd Clutch
- 3rd Clutch
- 4th Clutch
- Transmission Cutaway View
- P Position
- N Position
- 1st Gear
- Functional Diagram
- Shift Control
- Grade Logic Control: Ascending Control
- Grade Logic Control: Descending Control
- Clutch Pressure Control
- Lock-up Control
- PCM Inputs and Outputs
- Hydraulic Controls
- Main Valve Body
- Regulator Valve Body
- Regulator Valve
- Servo Body
- Accumulator
- Distribution of Hydraulic Pressure
- D Position: 1st gear shifting from the N position
- D Position: Driving in 1st gear
- D Position: Shifting between 1st gear and 2nd gear
- D Position: Driving in 2nd gear
- D Position: Shifting between 2nd gear and 3rd gear
- D Position: Driving in 3rd gear
- D Position: Shifting between 3rd gear and 4th gear
- D Position: Driving in 4th gear
- 2 Position
- 1 Position
- R Position: Shifting to the R position from the P or N position
- R Position: Driving in reverse gear
- Reverse Inhibitor Control
- Lock-up System
- No Lock-up
- Partial Lock-up
- Full Lock-up
- Idler Gear Shaft Bearing Replacement
- Control Shaft Oil Seal Replacement
- Control Shaft Bearing Replacement
- Bearing Removal
- Bearing Installation
- Valve Body and ATF Strainer Removal
- Shift Solenoid Valve Installation
- Mainshaft Bearing and Oil Seal Replacement
- Countershaft Bearing Replacement
- Secondary Shaft Bearing Replacement
- Countershaft Reverse Selector Hub Installation
- Secondary Shaft Ball Bearing, Idler Gear Removal and Installation
- Removal
- Installation
- Idler Gear/Idler Gear Shaft Replacement
- Valve Body and ATF Strainer Installation
- End Cover Installation
- Carrier Bearing Replacement
- Oil Seal Replacement
- Carrier Bearing Outer Race Replacement
- Engine Performance Diagnostic Routine Outline - General Information
- Engine Performance Safety Precautions
- Parasitic Load Explanation & Test Procedures - General Information 2
- Waveforms - Injector Pattern Tutorial - General Information 2
- Electrostatic Discharge Warning - General Information
- State Emission Standards - Diesel
- Diagnostic Trouble Code Definitions - General Information
- Intermittent Failures
- Opens and Shorts
- If the MIL did not stay on
- How to Update the ECM/PCM
- How to Substitute the ECM/PCM
- Electronic Control System
- Fail-safe Function
- Back-up Function
- Two Driving Cycle Detection Method
- ECM/PCM Data
- PGM-FI System
- Air Conditioning (A/C) Compressor Clutch Relay
- Air Fuel Ratio (A/F) Sensor
- Barometric Pressure (BARO) Sensor
- Camshaft Position (CMP) Sensor B (Top Dead Center (TDC) Sensor)
- Crankshaft Position (CKP) Sensor
- Engine Coolant Temperature (ECT) Sensor
- Ignition Timing Control
- Injector Timing and Duration
- Intake Air Temperature (IAT) Sensor
- Knock Sensor
- Malfunction Indicator Lamp (MIL) Indication (In relation to Readiness Codes)
- Manifold Absolute Pressure (MAP) Sensor
- Secondary Heated Oxygen Sensor (Secondary HO2S)
- Starting Control
- Throttle Position (TP) Sensor
- Vehicle Speed Sensor (VSS) (M/T)
- Camshaft Position (CMP) Sensor A
- Idle Control System
- Brake Pedal Position Switch
- Idle Air Control (IAC) Valve
- Power Steering Pressure (PSP) Switch
- Fuel Cut-off Control
- Fuel Pump Control
- PGM-FI Main Relay 1 and 2
- Intake Air System
- Intake Air Bypass Control Thermal Valve
- Intake Manifold Runner Control Valve Position Sensor
- Throttle Body
- Three Way Catalytic Converter (TWC)
- Positive Crankcase Ventilation (PCV) System
- Evaporative Emission (EVAP) Control System
- EVAP Canister
- EVAP Canister Purge Valve
- Fuel Tank Pressure (FTP) Sensor
- EVAP Two Way Valve and EVAP Bypass Solenoid Valve
- Idle Control System Diagram
- Intake Air System Diagram
- Intake Manifold Runner Control (IMRC) System
- Evaporative Emission (EVAP) Control Diagram
- Catalytic Converter Monitor and Readiness Code
- Enable Criteria
- When the HDS is used
- Evaporative Emission (EVAP) Control System Monitor and Readiness code
- Air/Fuel Ratio (A/F) Sensor Heater Monitor Readiness Code
- Procedure
- Misfire Monitor and Readiness Code
- Fuel System Monitor and Readiness Code
- Comprehensive Component Monitor and Readiness Code
- How to Retrieve a Diagnostic Trouble Codes
- Diagnostic Trouble Codes Troubleshooting
- DTC 7: An Open in the Air Mix Control Motor Circuit
- DTC 9: A Problem in the Air Mix Control Linkage, Door, or Motor
- DTC 11: A Problem in the Mode Control Linkage, Doors, or Motor
- Condenser Fan Circuit Troubleshooting
- Radiator and Condenser Fan Common Circuit Troubleshooting
- Compressor Clutch Circuit Troubleshooting
- A/C Pressure Switch Circuit Troubleshooting
- Refrigerant Leak Test
- Performance Test
- Engine Removal
- Vtec Rocker Arm Test
- Valve Clearance Adjustment
- Crankshaft Pulley Removal and Installation
- Cam Chain Removal
- Cam Chain Installation
- Chain Case Oil Seal Installation
- Cylinder Head Removal
- Rocker Arm and Shaft Disassembly/reassembly
- Camshaft Inspection
- Valve, Spring, and Valve Seal Removal
- Valve Guide Replacement
- Valve, Spring, and Valve Seal Installation
- Cylinder Head Installation
- Cylinder Honing
- Crankshaft Installation
- Transmission End Crankshaft Seal Installation - in Car
- Removal & Installation
- Torque Specifications