Transaxle/transmission Cooling: Removal & Installation Ford Fusion I рестайлинг

REMOVAL

Note. MERCON®, MERCON® V, MERCON® SP, Motorcraft Premium Automatic Transmission Fluid, Motorcraft Continuously Variable Chain Type Transmission Fluid and FNR5 Automatic Transmission Fluid are not interchangeable transmission fluids. The use of any transmission fluid other than what is recommended for this transaxle will cause transaxle damage.

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to «JACKING AND LIFTING»(ref-291849) article.
2. Disconnect the upper transmission fluid cooler tube from the radiator.
3. If equipped, remove the bolts and the splash shield.
4. Remove the front splash shield. Remove the 2 screws. Remove the 4 retainers. Remove the 4 bolts and the splash shield.
5. Disconnect the lower transmission fluid cooler tube from the radiator.
6. Disconnect the transmission fluid cooler hoses from the transmission fluid cooler tubes.
7. Remove the 2 bolts and remove the transmission fluid cooler tubes.
8. Remove the transmission fluid cooler tubes from the retainers.
9. Remove the transmission fluid cooler tube retainer and remove the transmission fluid cooler tubes.

INSTALLATION

1. Install new O-rings on the transmission fluid cooler tubes.
2. Install the transmission fluid cooler tubes. Tighten to 10 Nm (89 lb-in).
3. Position the transmission fluid cooler tubes in place and install the retainer.
4. Install the transmission fluid cooler tubes in the retainers.
5. Position the transmission fluid cooler hoses in place.
6. Connect the transmission fluid cooler hoses to the transmission fluid cooler tubes.
7. Install the lower transmission fluid cooler tube in the radiator. Tighten to 30 Nm (22 lb-ft).
8. Install the front splash shield. Position the splash shield in place and install the 2 screws. Install the 4 retainers. Install the 4 bolts.
9. If equipped, install the bolts and the splash shield.
10. Install the upper transmission fluid cooler tube in the radiator. Tighten to 30 Nm (22 lb-ft).
11. Remove the transmission fluid fill plug.
12. Check the transmission fluid level and add transmission fluid as necessary.
13. Install the transmission fluid fill plug. Tighten to 39 Nm (29 lb-ft).

Note. MERCON®, MERCON® V, MERCON® SP, Motorcraft Premium Automatic Transmission Fluid, Motorcraft Continuously Variable Chain Type Transmission Fluid and FNR5 Automatic Transmission Fluid are not interchangeable transmission fluids. The use of any transmission fluid other than what is recommended for this transaxle will cause transaxle damage.

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to «JACKING AND LIFTING»(ref-291849) article.
2. Disconnect the upper transmission fluid cooler tube from the radiator.
3. Remove the bolts and the splash shield.
4. Remove the front splash shield. Remove the 2 screws. Remove the 4 retainers. Remove the 4 bolts and the splash shield.
5. Disconnect the lower transmission fluid cooler tube from the radiator.
6. Disconnect the transmission fluid cooler hoses from the transmission.
7. Remove the transmission fluid cooler tubes from the retainers.
8. Remove the transmission fluid cooler tube retainer and remove the transmission fluid cooler tubes.

1. Position the transmission fluid cooler tubes in place and install the retainer.
2. Install the transmission fluid cooler tubes in the retainers.
3. Position the transmission fluid cooler hoses in place.
4. Connect the transmission fluid cooler hoses to the transaxle.
5. Install the lower transmission fluid cooler tube to the radiator. Tighten to 30 Nm (22 lb-ft).
6. Install the front splash shield. Position the splash shield in place and install the 2 screws. Install the 4 retainers. Install the 4 bolts.
7. Install the splash shield and the bolts.
8. Install the upper transmission fluid cooler tube to the radiator. Tighten to 30 Nm (22 lb-ft).
9. Check the transmission fluid level and add transmission fluid as necessary.