THEORY OF OPERATION
The objective of the Idle "Speed Rationality" is to monitor the ability to achieve and maintain a steady idle condition. The Engine Speed Error is calculated by comparing the difference between the Idle Set Speed from the Engine Speed and filtering the result. If engine speed does not come within a calibrated threshold of target idle speed, a timer is started. If the timer reaches its maximum threshold without the idle set speed returning inside of its calibrated threshold, a soft failure is generated.
The objective of the Idle "Speed Rationality" is to monitor the ability to achieve and maintain a steady idle condition. The Engine Speed Error is calculated by comparing the difference between the Idle Set Speed from the Engine Speed and filtering the result. If engine speed does not come within a calibrated threshold of target idle speed, a timer is started. If the timer reaches its maximum threshold without the idle set speed returning inside of its calibrated threshold, a soft failure is generated.
Spark adjustment during a cold start is intended to provide quick response to idle speed variations. The spark adjust diagnostics monitors spark advance on a cold start over a period of time, then compares the average spark advance to a threshold.
The brake switch rationality checks both failure modes of the brake switch. The brake switch stuck on test checks for a high vehicle speed condition where the brake switch is unexpectedly depressed. The brake switch stuck off test checks for repeated vehicle stop maneuvers without the brake switch depressed.
The brake switch rationality checks both failure modes of the brake switch. The brake switch stuck on test checks for a high vehicle speed condition where the brake switch is unexpectedly depressed. The brake switch stuck off test checks for repeated vehicle stop maneuvers without the brake switch depressed.
The brake switch rationality checks both failure modes of the brake switch. The brake switch stuck on test checks for a high vehicle speed condition where the brake switch is unexpectedly depressed. The brake switch stuck off test checks for repeated vehicle stop maneuvers without the brake switch depressed.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Speed Control Switch is hardwired to the Steering Column Control Module (SCCM). The SCCM is located near the top of the steering column below the steering wheel. The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The speed control messages are bussed to the Powertrain Control Module (PCM) via the Can Bus.
The Powertrain Control Module (PCM) stores in its EEPROM vehicle information data transmitted over the CAN Bus from the BCM. If the stored information in the PCM does not match the information obtained over the CAN Bus, the DTC will set.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.
MultiAir is an electronically controlled variable intake valve phase and lift system. Unlike conventional intake valve phase and lift system which controls all the cylinder intake valves simultaneously and in the same proportion; MultiAir, through the use of an electronically controlled " hydraulic link" between the camshaft and intake valve, allow for each intake valve to be controlled independently. The valve lift and timing can be adjusted infinitely.
The MultiAir valve train has a mechanical camshaft lobe acting on a hydraulic pump located between the camshaft intake lobe and the intake valve. The pump provides oil under pressure to a two-way electro-hydraulic solenoid valve called the Variable Valve Actuator (VVA) Solenoid. The VVA Solenoid is electronically controlled during the specific intake cam lobe event by the Powertrain Control Module (PCM). During the event the VVA Solenoid is commanded to either hold oil pressure or bleed oil. The Variable Valve Actuator (VVA) Solenoid is a normally open solenoid. The PCM provides 12 volts to close the solenoid. The position of the VVA Solenoid determines the intake valve timing and lift. This change on valve action is similar to creating a change in the camshaft lobe profile affecting lift and duration of the valve opening.