- Disconnect battery. Remove intake cover. Partially drain coolant from radiator. Remove oil dipstick. Disconnect upper radiator hose at water crossover. Note location and disconnect left side spark plug wires. Remove left and right torque struts.
- Remove right fan. Disconnect battery cable at generator. Disconnect cable harness cup at camshaft cover and position aside. Disconnect PCV fresh air tube from camshaft cover. Remove EGR pipe.
- Disconnect water pump drive belt. Using Pulley Remover (J-38825), remove water pump pulley. Remove camshaft seal retainer screws and remove seal. Disconnect battery cable retainer at front of camshaft cover. Remove camshaft cover screws.
- Remove camshaft cover by moving camshaft drive end of cover up and then pivot entire cover around water pump drive shaft. Continue moving cover upward and pivoting so that edge of cover closely follows left edge of intake manifold cover. (Схема №3) Discard cover seal if there is any evidence of damage or if seal comes out of groove in cover during removal. Spark plug seals may be reused if undamaged.
Contents
Wiring diagrams Section: Mechanical- Engine Identification
- Valve Clearance Adjustment
- Trouble Shooting
- Removal & Installation
- Fuel Pressure Release
- Cooling System Bleeding
- Removal (Preferred Method)
- Installation (Preferred Method)
- Removal (Alternate Method)
- Installation (Alternate Method)
- Removal & Installation (Left)
- Removal & Installation (Right)
- Cylinder Head
- Timing Chain Tensioner
- Removal (Left)
- Installation (Left)
- Removal (Right)
- Installation (Right)
- Setting Camshaft Timing
- Thermostat
- Valve Stem Oil Seal & Valve Spring
- Cylinder Head Gasket Surface
- Valve Springs
- Valve Stem Oil Seals
- Valve Guides
- Valve Seat
- Valves
- Valve Seat Correction Angles
- Fitting Pistons
- Piston Rings
- Rod Bearings
- Crankshaft & Main Bearings
- Thrust Bearing
- Cylinder Block Deck Surface
- Engine Lubrication System
- Crankcase Capacity
- Oil Pressure
- Removal & Disassembly
- Reassembly & Installation
- Torque Specifications
- General Specifications
- Camshaft Specifications
- Engine Valves & Valve Springs Specifications
- Cylinder Block Specifications
- Connecting Rods Specifications
- Cylinder Head Specifications
- Crankshaft, Main Bearings & Connecting Rod Bearings Specifications
- Pistons, Piston Pins & Piston Rings Specifications
- Valve Lifters Specifications
- Abbreviations
- Accessory Drive Belts
- Adjustments
- Airbag
- Anti-Lock/traction Control
- Application
- Automatic HVAC System
- Automatic Trans
- Axle Shafts
- Basic Trouble Shooting
- Body, Cab Control Systems
- Brakes
- Charging System
- Check Lists
- Computer Relearn
- Cooling Fan
- Cruise Control Systems
- Diagnostic Connector Locations
- Door Locks & Anti-Theft Systems
- Drive Cycles
- Driveline/axles
- DTC Index
- Electrical
- Electrical Component Locations
- Electronic Suspension
- Emission Applications
- Engine
- Engine Performance
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- General Servicing - All Makes
- Headlights
- Heated Glass/defoggers
- Identification
- Manual & Power Steering
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Memory Modules
- Metric Conversions
- Mirrors
- Mode 6
- Procedures
- Removal & Installation
- Reset Procedures
- Restraints
- Rpo Codes
- Seats
- Sensor Range Charts
- Specifications
- Starter
- Steering
- Steering Column
- Steering Column Switches
- Sun Roof/t-Top/convertible Top
- Suspension Front
- Suspension Rear
- Testing & Diagnostics
- Theory & Operation
- Traction Control Disable
- Transmission
- Wheel Alignment
- Windows
- Wiper/washer Systems
- Wiring Diagrams - Engine Performance