22 11 011 Replacing left engine mount (S65)
Necessary preliminary tasks
- Secure «ENGINE IN INSTALLATION POSITION»(/bmw/m3/e90-2007-2013/remont/mechanical/#engine-repair-e90__11-00-670-securing-engine-in)
- «LOWER FRONT AXLE SUPPORT»(/bmw/m3/e90-2007-2013/remont/axle-shafts/#front-axle-repair-e90__31-11-506-loweringraising-front-axle)
Slacken nut (1).
Tightening torque 22 11 1AZ .
Installation
Replace nuts.
Scheme 699
Installation
Installation position of engine mount determined by locating pin.
Necessary preliminary tasks
- Remove «18 40 020 REMOVING AND INSTALLING/REPLACING RIGHT EXHAUST MANIFOLD (S65)»(/bmw/m3/e90-2007-2013/remont/exhaust/#exhaust-system-repair-e90__18-40-020-removing-and-installingreplacing)
Observe SAFETY INSTRUCTIONS on raising the vehicle.
Release screws (2).
Remove engine support arm.
Tightening torque 22 11 3AZ .
Note. Illustration similar
Scheme 700
22 11 001 Replacing right engine mount (S65)
Necessary preliminary tasks
- Remove «RIGHT ENGINE SUPPORT ARM»(/bmw/m3/e90-2007-2013/remont/mechanical/#engine-and-gearbox-suspension-repair-e90)
Slacken nut (1).
Tightening torque 22 11 1AZ .
Installation
Replace nuts.
Scheme 701
Installation
Installation position of engine mount determined by locating pin.
- Secure «ENGINE IN INSTALLATION POSITION»(/bmw/m3/e90-2007-2013/remont/mechanical/#engine-repair-e90__11-00-670-securing-engine-in)
- Release «TIE ROD ON STEERING GEAR»(/bmw/m3/e90-2007-2013/remont/manual-power-steering/#steering-and-wheel-alignment-repair-e90__32-21-231-replacing-removing-and)
Observe SAFETY INSTRUCTIONS on raising the vehicle.
Release screws (1).
Remove engine support arm (2).
Tightening torque 22 11 3AZ .
Note. Illustration similar
Scheme 702
22 31 050 Replacing crossmember for transmission mounting
Note. Operations are identical to Replacing RUBBER MOUNT for transmission mounting.
- Remove rear underbody protection.
- Support transmission with lifter.
Remove screws and nuts.
Remove transmission cross-member (1).
Remove rubber mount from transmission cross-member.
Tightening torque 22 32 3AZ/4AZ .
Scheme 703
- Remove «REAR UNDERBODY PROTECTION»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-47-491-removing-and-installingreplacing)
- Support transmission with hydraulic lifter.
Release screws (1) and nuts (2) and remove transmission cross-member.
Remove rubber mount from transmission cross-member.
Tightening torque 23 71 2AZ/5AZ .
Note. Illustration similar
Scheme 704
Note. Operations are identical to Replacing RUBBER MOUNT for transmission mounting.
- Remove «REAR UNDERBODY PROTECTION»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-47-491-removing-and-installingreplacing)
Support transmission with hydraulic jack.
Release screws (1).
Tightening torque: 22 32 4AZ .
Unscrew nuts (2).
Tightening torque: 22 32 3AZ .
Remove cross-member.
Scheme 705
- Remove rear underbody protection.
- Support transmission with lifter.
Remove screws and nuts.
Remove transmission cross-member (1).
Remove rubber mount from transmission cross-member.
Tightening torque 22 32 3AZ/4AZ .