- Engine oil temperature at least 60 ° C
- Vehicle must be level (horizontal)
- Wait a few minutes after switching off the engine to allow the oil to flow back into the sump.
Contents
Section: Mechanical- Engine Number
- Special Tools and Equipment
- Removing
- Work Sequence
- Installing
- Poly V-Belt, Component Overview
- Identifying Poly V-Belt Routing
- Special Tools and Equipment Required
- Tightening Torque
- Sealing Flanges and Flywheel, Removing and Installing
- Special Tools, Testers and Auxiliary Items Required
- Timing Chain Covers & Dual Mass Flywheel, Assembly Overview
- Upper Cover for Camshaft Timing Chain, Component Overview
- Timing Chain, Component Overview
- Special Tools, Equipment, and Material Required
- Crankshaft, Removing and Installing
- Crankshaft, Component Overview
- Removing and Installing Sensor Wheel
- Installed Location
- Tightening Torques
- Crankshaft Dimensions
- Pistons and Connecting Rods, Component Overview
- Checking Piston
- Checking Cylinder Bore
- Installing Piston with Tool T10147
- Piston and Cylinder Dimensions
- Cylinder Head, Removing and Installing
- Cylinder Head, Component Overview
- Checking Cylinder Head for Distortion
- Overview of Intake Manifold Components
- Cylinder Head, Removing
- Conditions
- Compression Pressure
- Valve Gear, Servicing
- Valve Gear, Component Overview
- Camshaft Identification
- Coat Surface of Bearing Caps 7 and 8 with Lubricating Paste
- Installed Position of Bearing Caps for Camshafts
- Disassembling and Assembling Valve Timing Housing
- Checking Filter of Valve Timing Housing for Dirt
- Valve Dimensions
- Valve Seats, Machining
- Calculating Maximum Permissible Machining Dimension
- Machining Intake Valve Seat
- Machining Exhaust Valve Seat
- Lubrication System Components, Removing and Installing
- Lubrication System, Component Overview
- Removing and Installing Oil Spray Jet
- Oil Filter Bracket, Component Overview
- Installed Position of Oil Seal and Plastic Element in Oil Cooler
- Oil Pump, Component Overview
- Checking Backlash
- Checking Axial Clearance
- Checking Oil Pressure Switch
- Checking Oil Pressure
- Assembling
- Engine Oil, General Information
- Viscosity Grades and Oil Specifications
- Oil Level, Checking
- 5 & 6-speed Manual Transmission (02m & 02y Awd)
- A/c Compressor
- Abbreviations
- Accessories Control Systems
- Accessory Drive Belts
- Airbag
- Anti-Lock/traction Control
- Automatic HVAC System
- Automatic Trans
- Axle Shafts
- Basic Trouble Shooting
- Blowers, Superchargers & Turbochargers
- Brakes
- Cabin Air Filter
- Charging System
- Check Lists
- Clutches Manual & Hydraulic
- Cooling Fan
- Cooling System (mechanical)
- Cruise Control Systems
- Diagnostic Connector Locations
- Differentials & Drive Axles
- Door Locks & Anti-Theft Systems
- Drive Cycles
- Driveline/axles
- Driveshaft & Universal Joints
- DTC Index
- Electrical Component Locations
- Emission Applications
- Engine
- Engine Performance
- Exhaust
- Exterior Body Panels
- Fuel System
- Fuses & Circuit Breakers
- Identification
- Ignition System
- Manual Trans
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Metric Conversions
- Procedures
- Reset Procedures
- Restraints
- Specifications
- Starter
- Steering
- Suspension Front
- Suspension Rear
- Suspension, Wheels, Steering
- Timing Belt
- Traction Control Disable
- Transmission
- Wheel & Tire System
- Wheel Alignment