FLUID CAPACITIES
| Application (1) | Refill - Qts. (L) | Dry-Fill - Qts. (L) |
|---|
| 01L | 3.7-4.2 (3.5-4.0) | 10.4 (9.8) |
| (1) Capacities are approximate. |
| (1) | Capacities are approximate. |
TRANSAXLE FLUID CAPACITIES
| Application | Qts. (L) |
|---|
| Front Final Drive | 1.4 (1.3) |
| Transfer Case | 0.93 (0.8) |
| Rear Final Drive | 1.6 (1.5) |
FINAL DRIVE & TRANSFER CASE FLUID CAPACITIES
Note. Transfer case may also be known as a distributor gear.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| ATF Inspection Plug | 59 (80) |
| ATF Cooler Line Bolt | (1) |
| Center Differential Fill Plug | 26 (35) |
| Clamping Sleeve Nut | 30 (40) |
| Differential Cover-To-Transmission Housing Bolt | 17 (23) |
| Drive Shaft-To-Rear Final Drive Bolt (2) | (3) 41 (55) |
| Drive Shaft-To-Transaxle Flange Bolt (2) | (3) 41 (55) |
| Drive Shaft Intermediate Bearing-To-Body Bolt | 18 (25) |
| Exhaust Clamp Sleeve | 30 (40) |
| Front Final Drive Fill Plug | 22 (30) |
| Front Crossmember (Below Exhaust System)-To-Body Bolt | 18 (25) |
| Heat Shield-To-Transmission Bolt | 17 (23) |
| Heat Shield (Drive Shaft - Torsen Differential) Bolt | 18 (25) |
| Left Drive Axle Flange Mounting Bracket Bolt | 17 (23) |
| Rear Final Drive Fill Plug | 26 (35) |
| Right Drive Axle Flange-To-Transmission Bolt | 18 (25) |
| Selector Lever Bracket-To-Transmission Bolt | 17 (23) |
| Selector Cable-To-Transmission Heat Shield Bolt |
| M6 | 80 INCH lbs. (9 N.m) |
| M8 | 17 (23) |
| Transfer Case Fill Plug | 26 (35) |
| Transmission Support-To-Transmission Bolt | 30 (40) |
| Transmission Support-To-Transmission Mount Bolt | 37 (50) |
| Transmission Mount-To-Subframe Bolt | 17 (23) |
| Wheel Lug Bolts | 89 (120) |
| INCH Lbs. (N.m) |
| ATF Drain Plug | 106 (12) |
| ATF Screen-To-Valve Body Bolt | 44 (5) |
| Front Center Console Bolt | 44 (5) |
| Multi-Function Transmission Range Switch (F125)-To-Transmission Bolt | 71 (8) |
| Oil Pan-To-Transmission Housing Bolt | (4) 89 (10) |
| Selector Cable-To-Bracket Bolt | 106 (12) |
| Selector Lever Mounting Bracket Cover Nut | 89 (10) |
| Transmission RPM Sensor-To-Valve Body Bolt | 44 (5) |
| Valve Body-To-Transmission Bolt | (5) 71 (8) |
| (1) For torques specifications (Схема №12) (2) Replace fastener with new part during installation. (3) Threaded holes for bolts in drive flanges must always be cleaned. (e.g. using a tap). (4) Tighten bolts diagonally. (5) Hand tighten in a pattern from inner bolts to outer first. |
| (1) | For torques specifications (Схема №12) |
| (2) | Replace fastener with new part during installation. |
| (3) | Threaded holes for bolts in drive flanges must always be cleaned. (e.g. using a tap). |
| (4) | Tighten bolts diagonally. |
| (5) | Hand tighten in a pattern from inner bolts to outer first. |
