Home ReviewsRefund
Home/Opel/GT/Opel GT II (2007-2009)/Repair manual/Engine Controls and Fuel - 2.0L/DTC p2261
Contents Section: Engine Controls and Fuel - 2.0L All sections

DTC p2261 Opel GT II

Engine Controls and Fuel - 2.0L ~532 words

DTC p2261

Diagnostic Instructions

•Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
•Review Strategy Based Diagnosis for an overview of the diagnostic approach.
•Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P2261:

Turbocharger Bypass Valve Stuck Closed

System Description

The BorgWarner dual-scroll turbocharger (TC) incorporates a wastegate that is controlled by a pressure differential, that is determined by the engine control module (ECM) by means of a PWM solenoid, in order to regulate the pressure ratio of the compressor. A charge air bypass valve is integrated within the unit, and is also controlled by the ECM by utilizing a remotely mounted solenoid to prevent compressor surging and damage from vibrations by opening during abrupt closed throttle conditions. When the bypass valve is commanded open during closed throttle deceleration conditions, the bypass valve allows the air to recirculate in the TC and maintain compressor speed. Within a calibrated range during the closed throttle event, or upon a wide open throttle command, the bypass valve will then close to optimize TC response.

The purpose of this diagnostic is to determine if the charge air bypass valve is stuck closed. The ECM will first verify the integrity of the following sensors. The ECM then compares the actual measured mass air flow (MAF) to a modeled airflow that is derived from these inputs:

•The throttle position (TP)
•The engine speed
•The boost pressure sensor
•The manifold absolute pressure (MAP) sensor

Conditions for Running the DTC

•DTCs P0033, P0034, P0035, P0096, P0097, P0098, P0099, P0100, P0101, P0102, P0103, P0106, P0107, P0108, P0121, P0122, P0123, P0221, P0222, P0223, P0234, P0236, P0237, P0238, P0299, P2227, P2228, or P2229, is not set.
•The boost pressure versus the BARO pressure ratio is between 1.1-3.3.
•The charge air bypass valve has been commanded ON for greater than 1 second immediately after an abrupt closed throttle has occurred and the resulting pressure ratio across the compressor exceeds the calibrated pressure ratio limit.
•The battery voltage is between 10-18 volts.
•This DTC runs continuously within the enabling conditions.

Conditions for Setting the DTC

The ECM by comparing the measured MAF to the modeled MAF has detected a series of pulsations in the induction system that exceed a calibrated threshold.

Action Taken When the DTC Sets

DTC P2261 is a Type B DTC.

Conditions for Clearing the Mil/dtc

DTC P2261 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

•Turbocharger System Description
•Boost Control System Description

Electrical Information Reference (Except Opel Gt)

•Circuit Testing
•Connector Repairs
•Testing for Intermittent Conditions and Poor Connections
•Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information.

Circuit/system Verification

  1. Verify that DTC P0033, P0034, or P0035 is not set.
  2. Use the scan tool output controls to command the TC Bypass Solenoid ON and OFF. An audible click should be heard and felt.
  3. Set up the scan tool for a snapshot of the induction data list. With the emergency brake on, the vehicle transmission in neutral, and the engine idling, perform a wide open throttle and then quickly release the accelerator. Review the Boost Pressure Sensor parameter. There should not be any abnormal pulsations of the parameter.
  4. With the parking brake ON and the engine idling in neutral, perform an audible test of the valve by depressing the throttle wide open, then quickly releasing it to a closed throttle position. A valve that is stuck shut will generate a turkey gobble sound. There should not be any unusual noise.
  5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/system Testing

  1. Inspect for any damage, restrictions, improper routing or connecting of the vacuum hoses on the charge air bypass valve solenoid and the charge air bypass valve.
  2. Clear the DTC and operate the vehicle within the Conditions for Running the DTC.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

•Charge Air Bypass Valve Solenoid Replacement
•Charge Air Bypass Valve Replacement
•Control Module References for ECM replacement, setup, and programming

More articles — Engine