Home ReviewsRefund
Home/Opel/Combo/Opel Combo C (2002-2011)/Repair manual/DOHC Petrol Engine/Special Service Tools
Contents Wiring diagrams Section: DOHC Petrol Engine All sections

Special Service Tools Opel Combo C

DOHC Petrol Engine 45 illustrations

Special Service Tools

KM-194-ESpark Plug Wrench
To remove/install spark plug
KM-235-DInstaller
To install crankshaft rear seal ring in conjunction with KM-658
KM-313Slide Hammer
To remove axle shafts in conjunction with KM-902
KM-412Engine Overhaul Stand
To hold removed engine
KM-412-3Adapter
To hold engine in conjunction with KM-412
KM-417Assembly Sleeve
Installation of oil pump and crankshaft front seal ring
KM-422Installer
To press seal ring in camshaft
KM-427Remover/Installer
To drive in cylindrical pins into cylinder block
KM-468-BHolding Wrench
To counterhold wheel hub when installing axle nut
KM-470-BAngular Torque Wrench
KM-471Adapter
To check pressurised cooling system in conjunction with cooling system tester
KM-498-BOil pressure gauge
To check engine oil pressure
KM-507-CRemover
Pressing out the tie rod heads
KM-527-AAdjustment pin
To lock steering column
MKM-558-10Closure Cap
MKM-571-BDial gauge
MKM-596-AMeasuring Instrument
To measure oil temperature
MKM-604-DTorx Bit and Socket Set
MKM-610Torque Wrench, 1/2"
Range 30 – 130 Nm / 22 – 96 lbf. ft.
MKM-611Torque Wrench, 3/8"
Range 10 – 60 Nm / 7 – 44 lbf. ft.
KM-652Locking Device
To lock flywheel or drive disc
KM-658Installer
To install crankshaft rear seal ring in conjunction with KM-235-1
MKM-669Torque Wrench, 1/2"
Range 30-500 Nm / 22-370 lbf. ft.
KM-726-AOil Filter Wrench
To remove/install the oil filter
KM-734Guide Drift
To centre clutch disc
KM-852Locking Tool
To lock the camshaft pulleys
MKM-883-1Engine Bridge
To remove/install engine damping blocks
KM-902Remover
To remove axle shafts in conjunction with KM-313
KM-904Base Frame
To remove/install engine and transmission with KM-6168
KM-911Flywheel Holder
To lock flywheel or drive disc
KM-913-AInstallation Wrench
To tension ribbed V-belt tension roller
KM-2358Wire Cable
To suspend engine
KM-6009Remover/Installer
To remove and install ignition module
KM-6010Assembly Sleeves
To install oil pump seal ring, crankshaft front seal ring
KM-6130Locating Pin
To fasten Ribbed V-belt tensioner
KM-6131Cam Lever
KM-6168Centring Tool
To remove and install front axle (with drive unit) in conjunction with KM-904
KM-6169Engine/Transmission Mount
Fixing of engine/transmission to front axle body
KM-6179Installation wrench, oxygen sensor
To remove and install oxygen sensors
KM-6181Locating Pin
Steering intermediate shaft adjustment
MKM-6182-1Pliers, straight
Removal/installation of compact clamps
MKM-6182-2Pliers, angled
Removal/installation of compact clamps
MKM-6182-3Pliers, flexible
Removal/installation of compact clamps
KM-6347Holder
For camshaft sprockets, torsional vibration damper
KM-J-34730-91Pressure Tester
To check fuel pressure

More articles — Engine and Engine Aggregates