Home ReviewsRefund
Home/Nissan/Note/Nissan Note E12 (2012-2016)/Repair manual/Body Electrical/Power Control System (Power Distribution System): Diagnosis
Contents Wiring diagrams Section: Body Electrical All sections

Power Control System (Power Distribution System): Diagnosis Nissan Note E12

Body Electrical ~2509 words

DTC INDEX

DTCDescription
DTC U1000CAN COMM CIRCUIT
DTC U1010CONTROL UNIT (CAN)
DTC B2614ACC RELAY CIRCUIT
DTC B2615BLOWER RELAY CIRCUIT
DTC B2616IGNITION RELAY CIRCUIT
DTC B2618BCM
DTC B261APUSH-BUTTON IGNITION SWITCH
DTC B26F1IGNITION RELAY
DTC B26F2IGNITION RELAY
DTC B26F6BCM

DTC INDEX

SELF DIAGNOSTIC RESULT

Refer to " DTC INDEX ".

ACTIVE TEST

Test ItemDescription
INSIDE BUZZERThis test is able to check combination meter warning chime operation [Take Out/Knob/Key/Off].
LCDThis test is able to check combination meter display information [Off/LK WN/OUTKEY/NO KY/BATT/INSRT/SFT P/ROTAT/ID NG/B & P I/B & P N].
BATTERY SAVERThis test is able to check battery saver operation [On/Off].
ENGINE SW ILLUMIThis test is able to check push-button ignition switch START indicator operation [On/Off].
PUSH SWITCH INDICATORThis test is able to check push-button ignition switch indicator operation [On/Off].
INT LAMPThis test is able to check interior room lamp operation [On/Off].
INDICATORThis test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
FLASHERThis test is able to check hazard lamp operation [LH/RH/Off].
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer operation [On/Off].
HORNThis test is able to check horn operation [On].
P RANGEThis test is able to check CVT shift selector illumination operation [On/Off].

DTC DETECTION LOGIC

Note. U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result procedure.

CONSULT DisplayDTC Detection ConditionPossible Cause
CAN COMM CIRCUIT [U1000]When any listed module cannot communicate with CAN communication signal continuously for 2 seconds or more with ignition switch ONIn CAN communication system, any item (or items) of the following listed below is malfunctioning. Transmission Receiving (ECM) Receiving (VDC/TCS/ABS) Receiving (METER/M & A) Receiving (TCM) Receiving (IPDM E/R)

Diagnosis Procedure

  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch ON and wait for 2 second or more. Check "SELF-DIAG RESULTS". Is "CAN COMM CIRCUIT" displayed? YES: Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation manual. NO: Refer to " «INTERMITTENT INCIDENT»(ref-675571-S38824794042014120500000) ".
CONSULT DisplayDTC Detection ConditionPossible Cause
CONTROL UNIT (CAN) [U1010]BCM detected internal CAN communication circuit malfunction.BCM
  1. REPLACE BCM When DTC "U1010" is detected, replace BCM. : Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ".
CONSULT DisplayDTC detecting conditionPossible cause
ACC RELAY CIRCUIT [B2614]An immediate operation of accessory relay-2 is requested by BCM, but there is no response for more than 1 second.Harness or connectors. Accessory relay-2. BCM.

DTC CONFIRMATION PROCEDURE

  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ACC, and wait for 1 second or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B2614 detected? YES: Go to " «DIAGNOSIS PROCEDURE»(ref-675633-S08970634622014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK ACCESSORY RELAY-2 CONTROL SIGNAL VOLTAGE Disconnect accessory relay-2 connector. Check voltage between accessory relay-2 connector M39 and ground. Accessory relay-2 Ground Condition Voltage (Approx.) Connector Terminal M39 1 - Ignition: OFF 0 V Ignition: ACC or ON Battery voltage Is the inspection result normal? YES: GO TO 3 . NO: GO TO 2.
  2. CHECK ACCESSORY RELAY-2 CONTROL SIGNAL CIRCUIT Turn ignition switch OFF. Disconnect BCM connector M98. Check continuity between BCM connector M98 and accessory relay-2 connector M39. BCM Accessory relay-2 Continuity Connector Terminal Connector Terminal M98 96 M39 1 Yes Check continuity between BCM connector M98 and ground. BCM Ground Continuity Connector Terminal M98 96 No Is the inspection result normal? YES: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ". NO: Repair or replace harness or connectors.
  3. CHECK ACCESSORY RELAY-2 GROUND CIRCUIT Check continuity between accessory relay-2 connector M39 and ground. Accessory relay-2 Ground Continuity Connector Terminal M39 2 Yes Is the inspection result normal? YES: Replace accessory relay-2. NO: Repair or replace harness or connectors.
CONSULT DisplayDTC Detection ConditionPossible Cause
BLOWER RELAY CIRCUIT [B2615]An immediate operation of blower relay is requested by BCM, but there is no response for more than 1 second.Harness or connectors. Blower relay. Fuse block J/B. BCM.
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 1 second or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B2615 detected? YES: Go to " «DIAGNOSIS PROCEDURE»(ref-675633-S27868791472014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK BLOWER RELAY CONTROL SIGNAL VOLTAGE Remove blower relay. Check voltage between blower relay connector J-1 and ground. Blower relay Ground Condition Voltage (Approx.) Connector Terminal J-1 2 - Ignition: OFF 0 V Ignition: ACC or ON Battery voltage Is the inspection result normal? YES: GO TO 3 . NO: GO TO 2.
  2. CHECK BLOWER RELAY CONTROL SIGNAL CIRCUIT Turn ignition switch OFF. Disconnect BCM connector M98. Check continuity between BCM connector M98 and blower relay connector J-1. BCM Blower relay Continuity Connector Terminal Connector Terminal M98 106 J-1 2 Yes Check continuity between BCM connector M98 and ground. BCM Ground Continuity Connector Terminal M98 106 No Is the inspection result normal? YES: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ". NO: Repair or replace harness or connectors.
  3. CHECK BLOWER RELAY GROUND CIRCUIT Check continuity between blower relay connector J-1 and ground. Blower relay Ground Continuity Connector Terminal J-1 1 Yes Is the inspection result normal? YES: Replace blower relay. NO: Repair or replace harness or connectors.
CONSULT DisplayDTC Detection ConditionPossible Cause
IGNITION RELAY CIRCUIT [B2616]An immediate operation of ignition relay-2 is requested by BCM, but there is no response for more than 1 second.Harness or connectors. Ignition relay-2. Fuse block J/B. BCM.
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 1 second or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B2616 detected? YES: Refer to " «DIAGNOSIS PROCEDURE»(ref-675633-S27868791472014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK IGNITION RELAY-2 CONTROL SIGNAL VOLTAGE Remove ignition relay-2. Check voltage between ignition relay-2 connector J-3 and ground. Ignition relay-2 Ground Condition Voltage (Approx.) Connector Terminal J-3 1 - Ignition: OFF 0 V Ignition: ON Battery voltage Is the inspection result normal? YES: GO TO 3 . NO: GO TO 2.
  2. CHECK IGNITION RELAY-2 CONTROL SIGNAL CIRCUIT Turn ignition switch OFF. Disconnect BCM connector M98. Check continuity between BCM connector M98 and ignition relay-2 connector J-3. BCM Ignition relay-2 Continuity Connector Terminal Connector Terminal M98 99 J-3 1 Yes Check continuity between BCM connector M98 and ground. BCM Ground Continuity Connector Terminal M98 99 No Is the inspection result normal? YES: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ". NO: Repair or replace harness or connectors.
  3. CHECK IGNITION RELAY-2 GROUND CIRCUIT Check continuity between ignition relay-2 connector J-3 and ground. Ignition relay-2 Ground Continuity Connector Terminal J-3 2 Yes Is the inspection result normal? YES: Replace ignition relay-2. NO: Repair or replace harness or connectors.
CONSULT DisplayDTC Detection ConditionPossible Cause
BCM [B2618]An immediate operation of ignition relay-1 is requested by BCM, but there is no response for more than 1 secondHarness or connectors BCM IPDM E/R
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 1 second or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B2618 detected? YES: Refer to " «DIAGNOSIS PROCEDURE»(ref-675633-S15796391012014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK IGNITION RELAY-1 CONTROL SIGNAL VOLTAGE Check voltage between IPDM E/R connector E47 and ground. IPDM E/R Ground Condition Voltage (Approx.) Connector Terminal E47 90 - Ignition: ON Battery voltage Is the inspection result normal? YES: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ". NO: GO TO 2.
  2. CHECK IGNITION RELAY-1 CONTROL SIGNAL CIRCUIT Turn ignition switch OFF. Disconnect BCM connector M98 and IPDM E/R connector E47. Check continuity between BCM connector M98 and IPDM E/R connector E47. BCM IPDM E/R Continuity Connector Terminal Connector Terminal M98 98 E47 90 Yes Check continuity between BCM connector M98 and ground. BCM Ground Continuity Connector Terminal M98 98 No Is the inspection result normal? YES: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ". NO: Repair or replace harness or connectors.
CONSULT DisplayDTC Detection ConditionPossible Cause
PUSH-BUTTON IGNITION SWITCH [B261A]BCM detects a difference of signal for 1 second or more between the following information: Power supply position by push-button ignition switch. Power supply position from IPDM E/R (CAN).Harness or connectors Push-button ignition switch BCM
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 1 second or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B261A detected? YES: Refer to " «DIAGNOSIS PROCEDURE»(ref-675633-S32968396362014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL (PUSH-BUTTON IGNITION SWITCH) Disconnect push-button ignition switch connector. Check voltage between push-button ignition switch connector M25 and ground. Push-button ignition switch Ground Voltage (Approx.) Connector Terminal M25 8 - Battery voltage Is the inspection result normal? YES: GO TO 2. NO: GO TO 4 .
  2. CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R) Check voltage between IPDM E/R connector E47 and ground. IPDM E/R Ground Voltage (Approx.) Connector Terminal E47 81 - Battery voltage Is the inspection result normal? YES: GO TO 3. NO: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ".
  3. CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R) Turn ignition switch OFF. Disconnect IPDM E/R connector E47 and BCM connector M98. Check continuity between IPDM E/R connector E47 and push-button ignition switch connector M25. IPDM E/R Push-button ignition switch Continuity Connector Terminal Connector Terminal E47 81 M25 8 Yes Check continuity between IPDM E/R connector E47 and ground. IPDM E/R Ground Continuity Connector Terminal E47 81 - No Is the inspection result normal? YES: Refer to " «INTERMITTENT INCIDENT»(ref-675571-S38824794042014120500000) ". NO: Repair or replace harness or connectors.
  4. CHECK IGNITION SWITCH OUTPUT SIGNAL (BCM) Check voltage between BCM connector M98 and ground. BCM Ground Voltage (Approx.) Connector Terminal M98 76 - Battery voltage Is the inspection result normal? YES: GO TO 5. NO: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ".
  5. CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM) Turn ignition switch OFF. Disconnect BCM connector M98 and IPDM E/R connector E47. Check continuity between BCM connector M98 and push-button ignition switch connector M25. BCM Push-button ignition switch Continuity Connector Terminal Connector Terminal M98 76 M25 8 Yes Check continuity between BCM connector M98 and ground. BCM Ground Continuity Connector Terminal M98 76 - No Is the inspection result normal? YES: Refer to " «INTERMITTENT INCIDENT»(ref-675571-S38824794042014120500000) ". NO: Repair or replace harness or connectors.
CONSULT DisplayDTC detecting conditionPossible cause
IGN RELAY OFF [B26F1]BCM transmits the ignition relay control signal, but does not receive ignition switch ON signal (CAN) from IPDM E/R.Harness or connectors BCM IPDM E/R
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 2 seconds or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B26F1 detected? YES: Go to " «DIAGNOSIS PROCEDURE»(ref-675633-S42471505602014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK IPDM E/R SELF-DIAGNOSTIC RESULT Erase IPDM E/R DTCs. Turn ignition switch OFF. Turn ignition switch ON. Perform Self Diagnostic Result of IPDM E/R with CONSULT. Are any DTCs detected? YES: Refer to " «DTC INDEX»(ref-675597-S37601914522014120500000) ". NO: GO TO 2.
  2. CHECK IGNITION RELAY-1 CONTROL SIGNAL (IPDM E/R) Check voltage between BCM connector M98 and ground. BCM Ground Condition Voltage (Approx.) Connector Terminal M98 98 - Ignition: ON 0 V Is the inspection result normal? YES: GO TO 3. NO: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ".
  3. CHECK IGNITION RELAY-1 CONTROL SIGNAL CIRCUIT (IPDM E/R) Turn ignition switch OFF. Disconnect BCM connector M98 and IPDM E/R connector E47. Check continuity between BCM connector M98 and IPDM E/R connector E47. BCM IPDM E/R Continuity Connector Terminal Connector Terminal M98 98 E47 90 Yes Is the inspection result normal? YES: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ". NO: Repair or replace harness or connectors.
CONSULT DisplayDTC detecting conditionPossible cause
IGN RELAY ON [B26F2]BCM transmits the ignition relay control signal, but does not receive ignition switch ON signal (CAN) from IPDM E/R.Harness or connectors BCM IPDM E/R
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 2 seconds or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B26F2 detected? YES: Go to " «DIAGNOSIS PROCEDURE»(ref-675633-S04166803302014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK IPDM E/R SELF-DIAGNOSTIC RESULT Erase IPDM E/R DTCs. Turn ignition switch OFF. Turn ignition switch ON. Perform Self Diagnostic Result of IPDM E/R with CONSULT. Are any DTCs detected? YES: Refer to " «DTC INDEX»(ref-675597-S37601914522014120500000) ". NO: GO TO 2.
  2. CHECK IGNITION RELAY-1 CONTROL SIGNAL (IPDM E/R) Turn ignition switch OFF. Check voltage between IPDM E/R connector E47 and ground. IPDM E/R Ground Condition Voltage (Approx.) Connector Terminal E47 90 - Ignition: OFF Battery voltage Is the inspection result normal? YES: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ". NO: GO TO 3.
  3. CHECK IGNITION RELAY-1 CONTROL SIGNAL CIRCUIT (IPDM E/R) Turn ignition switch OFF. Disconnect BCM connector M98 and IPDM E/R connector E47. Check continuity between IPDM E/R connector E47 and ground. IPDM E/R Ground Continuity Connector Terminal E47 90 No Is the inspection result normal? YES: GO TO 4. NO: Repair or replace harness or connectors.
  4. CHECK IGNITION RELAY-1 CONTROL SIGNAL CIRCUIT VOLTAGE (IPDM E/R) Connect IPDM E/R connector E47. Check voltage between IPDM E/R connector E47 and ground. IPDM E/R Ground Condition Voltage (Approx.) Connector Terminal E47 90 - Ignition: OFF Battery voltage Is the inspection result normal? YES: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ". NO: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ".

Note. If DTC B26F6 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to " DTC LOGIC ". If DTC B26F6 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to " DTC LOGIC ".

CONSULT DisplayDTC Detection ConditionPossible Cause
BCM [B26F6]Ignition relay ON signal is not transmitted from IPDM E/R (CAN) when BCM turns ignition relay ON.BCM
  1. PERFORM SELF DIAGNOSTIC RESULT Turn ignition switch to ON, and wait for 0.5 second or more. Check Self Diagnosis Result of BCM with CONSULT. Is DTC B26F6 detected? YES: Go to " «DIAGNOSIS PROCEDURE»(ref-675633-S19858184262014120500000) ". NO: Inspection End.

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK SELF DIAGNOSTIC RESULT FOR IPDM E/R Erase IPDM E/R DTCs. Turn ignition switch OFF. Turn ignition switch ON. Perform Self Diagnostic Result of IPDM E/R with CONSULT. Are any DTCs detected? YES: Refer to " «DTC INDEX»(ref-675597-S37601914522014120500000) ". NO: GO TO 2
  2. CHECK IGNITION RELAY-1 POWER SUPPLY (IPDM E/R) Check voltage between IPDM E/R connector E47 and ground. IPDM E/R Ground Condition Voltage (Approx.) Connector Terminal E47 90 - Ignition: OFF 0 V Ignition: ON Battery voltage Is the inspection result normal? YES: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ". NO: GO TO 3.
  3. CHECK IGNITION RELAY-1 POWER SUPPLY (BCM) Check voltage between BCM connector M98 and ground. BCM Ground Condition Voltage (Approx.) Connector Terminal M98 98 - Ignition: OFF 0V Ignition: ON Battery voltage Is the inspection result normal? YES: Refer to " «INTERMITTENT INCIDENT»(ref-675571-S38824794042014120500000) ". NO: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ".

Regarding Wiring Diagram information, refer to " WIRING DIAGRAM ".

  1. CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL (PUSH-BUTTON IGNITION SWITCH) Turn ignition switch OFF. Disconnect push-button ignition switch connector and IPDM E/R connector E47. Check voltage between push-button ignition switch connector M25 and ground. Push-button ignition switch Ground Voltage (Approx.) Connector Terminal M25 8 - Battery voltage Is the inspection result normal? YES: GO TO 3 . NO: GO TO 2.
  2. CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM) Disconnect BCM connector M98. Check continuity between BCM connector M98 and push-button ignition switch connector M25. BCM Push-button ignition switch Continuity Connector Terminal Connector Terminal M98 76 M25 8 Yes Check continuity between BCM connector M98 and ground. BCM Ground Continuity Connector Terminal M98 76 - No Is the inspection result normal? YES: Replace BCM. Refer to " «REMOVAL AND INSTALLATION»(ref-675612-S22326735462014120500000) ". NO: Repair or replace harness or connectors.
  3. CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R) Check voltage between IPDM E/R connector E47 and ground. IPDM E/R Ground Voltage (Approx.) Connector Terminal E47 81 - Battery voltage Is the inspection result normal? YES: GO TO 5 . NO: GO TO 4.
  4. CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R) Disconnect BCM connector M98. Check continuity between IPDM E/R connector E47 and push-button ignition switch connector M25. IPDM E/R Push-button ignition switch Continuity Connector Terminal Connector Terminal E47 81 M25 8 Yes Check continuity between IPDM E/R connector E47 and ground. IPDM E/R Ground Continuity Connector Terminal E47 81 - No Is the inspection result normal? YES: Replace IPDM E/R. Refer to " «REMOVAL AND INSTALLATION»(ref-675597-S28632663882014120500000) ". NO: Repair or replace harness or connectors.
  5. CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT Check continuity between push-button ignition switch connector M25 and ground. Push-button ignition switch Ground Continuity Connector Terminal M25 4 - Yes Is the inspection result normal? YES: GO TO 6. NO: Repair or replace harness or connectors.
  6. CHECK PUSH-BUTTON IGNITION SWITCH Refer to " «COMPONENT INSPECTION»(ref-675633-S23054391212014120500000) ". Is the inspection result normal? YES: Refer to " «INTERMITTENT INCIDENT»(ref-675571-S38824794042014120500000) ". NO: Replace push-button ignition switch. Refer to " «REMOVAL AND INSTALLATION»(ref-675633-S19333351202014120500000) ".

Component Inspection

  1. CHECK PUSH-BUTTON IGNITION SWITCH Turn ignition switch OFF. Disconnect push-button ignition switch connector. Check continuity between push-button ignition switch terminals. Push-button ignition switch terminals Condition Continuity 4 - 8 Pressed Yes Not pressed No Is the inspection result normal? YES: Inspection End. NO: Replace push-button ignition switch.
  1. PERFORM WORK SUPPORT Perform INSIDE ANT DIAGNOSIS in Work Support of INTELLIGENT KEY with CONSULT. Refer to " «INTELLIGENT KEY: CONSULT FUNCTION (BCM - INTELLIGENT KEY)»(ref-675633-S09089998522014120500000) ". : GO TO 2.
  2. PERFORM SELF DIAGNOSTIC RESULT Perform Self Diagnostic Result of BCM with CONSULT. Are any DTCs detected? YES: Refer to " «DTC INDEX»(ref-675612-S32883553702014120500000) ". NO: GO TO 3.
  3. CHECK PUSH-BUTTON IGNITION SWITCH Check push-button ignition switch. Refer to " «COMPONENT INSPECTION»(ref-675633-S23054391212014120500000) ". Is the inspection result normal? YES: Refer to " «INTERMITTENT INCIDENT»(ref-675571-S38824794042014120500000) ". NO: Repair or replace malfunctioning parts.

More articles — Power Control System (Power Distribution System)