Home ReviewsRefund
Home/Lexus/HS/Lexus HS I (2009-2012)/Repair manual/Airbag/Occupant Classification System (Diagnostic Codes): Other
Contents Wiring diagrams Section: Airbag All sections

Occupant Classification System (Diagnostic Codes): Other Lexus HS I

Airbag ~2000 words

PROCEDURE

  1. PERFORM ZERO POINT CALIBRATION Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NG --> See step 3 OK: Go to next step
  2. CHECK DTC Turn the power switch on (IG). Clear the DTCs stored in the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . Clear the DTCs stored in the center airbag sensor assembly. Refer to «DTC CHECK / CLEAR»(ref-398246-S01125415292011051600000) . Turn the power switch off. Turn the power switch on (IG). Check for DTCs of the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . OK DTC B1785 is not output. HINT: Codes other than DTC B1785 may be output at this time, but they are not related to this check. RESULT Result Proceed to NG A OK B B --> See step 5 A: Go to next step
  3. REPLACE FRONT SEAT ASSEMBLY RH Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Replace the front seat assembly RH. Refer to «REMOVAL»(ref-398249-S33005380292011051600000) . NEXT: Go to next step
  4. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  5. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  1. PERFORM ZERO POINT CALIBRATION Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NG --> See step 3 OK: Go to next step
  2. CHECK DTC Turn the power switch on (IG). Clear the DTCs stored in the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . Clear the DTCs stored in the center airbag sensor assembly. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . Turn the power switch off. Turn the power switch on (IG). Check for DTCs of the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398246-S01125415292011051600000) . OK DTC B1786 is not output. HINT: Codes other than DTC B1786 may be output at this time, but they are not related to this check. RESULT Result Proceed to NG A OK B B --> See step 5 A: Go to next step
  3. REPLACE FRONT SEAT ASSEMBLY RH Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Replace the front seat assembly RH. Refer to «REMOVAL»(ref-398249-S33005380292011051600000) . NEXT: Go to next step
  4. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  5. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  1. PERFORM ZERO POINT CALIBRATION Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NG --> See step 3 OK: Go to next step
  2. CHECK DTC Turn the power switch on (IG). Clear the DTCs stored in the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . Clear the DTCs stored in the center airbag sensor assembly. Refer to «DTC CHECK / CLEAR»(ref-398246-S01125415292011051600000) . Turn the power switch off. Turn the power switch on (IG). Check for DTCs of the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . OK DTC B1787 is not output. HINT: Codes other than DTC B1787 may be output at this time, but they are not related to this check. RESULT Result Proceed to NG A OK B B --> See step 5 A: Go to next step
  3. REPLACE FRONT SEAT ASSEMBLY RH Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Replace the front seat assembly RH. Refer to «REMOVAL»(ref-398249-S33005380292011051600000) . NEXT: Go to next step
  4. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  5. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  1. PERFORM ZERO POINT CALIBRATION Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NG --> See step 3 OK: Go to next step
  2. CHECK DTC Turn the power switch on (IG). Clear the DTCs stored in the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . Clear the DTCs stored in the center airbag sensor assembly. Refer to «DTC CHECK / CLEAR»(ref-398246-S01125415292011051600000) . Turn the power switch off. Turn the power switch on (IG). Check for DTCs of the occupant classification ECU. Refer to «DTC CHECK / CLEAR»(ref-398103-S42135564202011051600000) . OK DTC B1788 is not output. HINT: Codes other than DTC B1788 may be output at this time, but they are not related to this check. RESULT Result Proceed to NG A OK B B --> See step 5 A: Go to next step
  3. REPLACE FRONT SEAT ASSEMBLY RH Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Replace the front seat assembly RH. Refer to «REMOVAL»(ref-398249-S33005380292011051600000) . NEXT: Go to next step
  4. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. OK: Go to next step
  5. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  1. REPLACE OCCUPANT CLASSIFICATION ECU Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Replace the occupant classification ECU. Refer to «REMOVAL»(ref-398090-S12538163052011051600000) . NEXT: Go to next step
  2. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  3. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  1. REPLACE OCCUPANT CLASSIFICATION ECU Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Replace the occupant classification ECU. Refer to «REMOVAL»(ref-398090-S12538163052011051600000) . NEXT: Go to next step
  2. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  3. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  1. CHECK SRS WARNING LIGHT Turn the power switch on (IG), and check the SRS warning light condition. HINT: If this trouble occurs, the SRS warning light is off. If the light is on, a DTC is output. Troubleshoot for the output DTC. OK After the primary check period, the SRS warning light goes off. HINT: The primary check is performed for approximately 6 seconds after the power switch is turned on (IG). NG --> See step 16 OK: Go to next step
  2. PERFORM ZERO POINT CALIBRATION Turn the power switch off. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NG --> See step 4 OK: Go to next step
  3. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NG --> See step 4 OK --> END
  4. RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT Turn the power switch off. Loosen the 4 installation bolts of the front seat assembly RH. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque. Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf) NEXT: Go to next step
  5. PERFORM ZERO POINT CALIBRATION Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NG --> See step 7 OK: Go to next step
  6. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NG --> See step 7 OK --> END
  7. READ VALUE USING PASSENGER SIDE BUCKLE SWITCH Turn the power switch on (IG). Using the Techstream, read Data List. Refer to «DATA LIST / ACTIVE TEST»(ref-398103-S03744302012011051600000) . Read the display when the passenger side buckle switch is operated. OCCUPANT DETECTION Tester Display Measurement Item / Range Normal Condition Diagnostic Note Passenger Buckle SW Passenger side buckle switch/ Set: The seat belt is fastened Unset: The seat belt is not fastened NG: Data is not determined Unset/Set - OK The Techstream display changes correctly in accordance with the operation of the buckle switch. NG --> See step 12 OK: Go to next step
  8. CHECK CONNECTORS Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Disconnect the connectors from the occupant classification ECU and 4 occupant classification sensors. Check that the terminals of the connectors are not damaged. OK The terminals are not deformed or damaged. NG --> REPLACE FRONT SEAT WIRE RH OK: Go to next step
  9. REPLACE OCCUPANT CLASSIFICATION ECU Connect the connectors to the 4 occupant classification sensors. Replace the occupant classification ECU. Refer to «REMOVAL»(ref-398090-S12538163052011051600000) . NEXT: Go to next step
  10. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  11. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  12. CHECK CONNECTORS Turn the power switch off. Disconnect the cable from the negative (-) battery terminal. Disconnect the connectors from the occupant classification ECU and front seat inner belt assembly RH. Check that the terminals of the connectors are not damaged. OK The terminals are not deformed or damaged. NG --> REPLACE FRONT SEAT WIRE RH OK: Go to next step
  13. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH Connect the connector to the occupant classification ECU. Replace the front seat inner belt assembly RH. Refer to «REMOVAL»(ref-398091-S30529843822011051600000) . NEXT: Go to next step
  14. PERFORM ZERO POINT CALIBRATION Connect the cable to the negative (-) battery terminal. Connect the Techstream to the DLC3. Turn the power switch on (IG). Using the Techstream, perform Zero Point Calibration. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . OK "Zero Point Calibration is complete." is displayed. NEXT: Go to next step
  15. PERFORM SENSITIVITY CHECK Using the Techstream, perform Sensitivity Check. Refer to «INITIALIZATION»(ref-398103-S03414413432011051600000) . Standard 27 to 33 kg (59.5 to 72.8 lb) NEXT --> END
  16. GO TO DTC CHART. Refer to «DIAGNOSTIC TROUBLE CODE CHART»(ref-398246-S23494487152011051600000)

More articles — Occupant Classification System (Diagnostic Codes)