Home/Volvo/S60/Volvo S60 I (2000-2004)/Repair manual/Seats, Interior Components - Removal, Replacement and Installation/Frame, replacing

Contents

Wiring diagrams Section: Seats, Interior Components - Removal, Replacement and Installation

Clips headlining, replacing

Method content

Preparatory work

Installing the clips

Clothes holder head restraint front seat

Ordering zip fastener catch

Removing clothes holder, head restraints

Floor carpet, front, replacing

Installing the sill trim panel

Soundproofing panel driver's side, replacing

The front sill trim panel

Removing the headlining

Installing the headlining

Grab handle

Installing the panel

Replacing the driver's side soundproofing panel

Replacing the passenger side soundproofing panel

Upholstery head restraint front

Removing the upholstery for the center head restraint

Installing the center head restraint upholstery

Upholstery outer head restraint rear

Installing the upholstery on folding head restraints

Floor carpet, rear, replacing

Headlining, replacing

Side panel, cargo compartment, replacing

Soundproofing panel, replacing

Upholstery middle head restraint rear

Removing the B-post panel

Removing the sill trim panel

Installing the B-post panel

B-post ventilation vent

Installing the B-post ventilation vent

Installing the C-post panel

Installing the rear side door side panel

Removing the parcel shelf

Installing the parcel shelf

Replacing the A-post panel

Removing the A-post panel

Installing the A-post panel

Replacing the front door side panel

Cable child seat

Removing the cable.

Installing cushion / upholstery

Release handle for the booster cushion

Control module heater pad, replacing

Electric motor backrest cushion, replacing

Heater pad, replacing

Replacing the height adjuster gas strut

Lifting the front seats in and out

Lumbar support backrest cushion, replacing

Power seat module (PSM), replacing

Replacing WHIPS

Removing the WHIPS system

Installing the WHIPS system

Seat rail

Replacing the side cushion

Seat cushion padding

Seat frame

Replacing seat rail

Removing the SIPS bag control module connector

Upholstery back rest, replacing

Upholstery, seat cushion, replacing

Installing the heater pad control module

Removing the front seat

Removing backrest cushion upholstery

Installing backrest cushion upholstery

Installing the front seat

Install the electric motor for the backrest cushion

Side panel, replacing

Removing the side panel from manual seats

Installing the side panel on manual seats

Installing the side panel on power seats

Preparations

Installing the lumbar support in the backrest cushion

Side panel

Finishing

Removing the electric motor for the backrest cushion

Install the electric motor

Electric motor cushion, replacing

Front seat, replacing

Heater pad backrest and cushion, replacing

Removing the front seat and important information

Removing upholstery

Installing upholstery and front seat

Installing the lumbar support

Removing the power seat module (PSM)

Installing the power seat module (PSM)

Ordering software

Seat heating module (SHM), replacing

Ignition off

Installing the seat heating module (SHM)

Seat rails front seat, replacing

Removing the seat rails

Removing rivet

Installing the seat rails

Side panel front seat, replacing

Installing the side panel, power front seat

Installing seat cushion upholstery

Whiplash unit, replacing

Installing the whiplash unit on non-folding seats

Installing the whiplash unit on folding seats

Electric motor, backrest rake

Occupant weight sensor (OWS), replacing

Important information

Storing the ID number for the occupant weight sensor (OWS)

Frame, replacing

Replacing backrest padding

Replacing bracket (cross stay)

Connector

Motors connector

Control panel

Replacing head restraint sleeves

Important

Types of heater pad

Foam filling with only front-rear channels

Foam filling with front-rear channels and one lateral channel

Foam filling with front-rear channels, one lateral channel and a design channel

Foam filling with front-rear channels, two lateral channels and a design channel

Foam filling with linked front-rear channels, two lateral channels and a design channel

Removing old heater pads

Positioning the heater pad

Positioning in relation to the channels in the foam filling

Finishing work after the heater pad has been bonded into place

Installing seats

Lifting seats in and out

The seat from the car

Preparation

Vehicles up to and including model year 2002 and a certain chassis number

Vehicles from and including Model year 2002 and a certain chassis number

Lumber support strap

Removing the control module

Installing the control module

Replacing protective pad

Replacing seat cushion padding

Seat rail drive end

Replacing SIPS bag

Removing components

Installing upholstery

Backrest (frame and mounting)

Backrest padding

Installing the bracket and crossmember

Installing the drive shaft

Head restraint front seat

Head restraint sleeves

Installing the connector

Protective pad

Removing power seats, tilting

Removing the power seat

Installing the power seat

Installing the seat belt buckle

Removing the seat rail, left hand side

SIPS airbag

Installing the tension spring

Installing the seat frame

Replacing backrest upholstery 1

Replacing backrest upholstery 2

Replacing the center armrest or integrated child seat

Replacing central head restraint sleeves

Center head restraint

Lock the hatch for long loads

Central head restraint sleeves

Backrest

Cushion, replacing

Upholstery, center armrest, replacing

Hatch for long loads

Upholstery, side cushion, replacing

All sections

Frame, replacing Volvo S60 I

Seats, Interior Components - Removal, Replacement and Installation

Frame, replacing

Cut the rear half moon clip attaching the upholstery to the cushion.

Remove two screws per side and the mounting.

Replace the backrest frame with mounting.

Install

In reverse order.