APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|---|
| Work Support | Changes the setting for each system function. |
| Self Diagnostic Result | Displays the diagnosis results judged by BCM. |
| CAN Diag Support Monitor | Monitors the reception status of CAN communication viewed from BCM. |
| Data Monitor | The BCM input/output signals are displayed. |
| Active Test | The signals used to activate each device are forcibly supplied from BCM. |
| Ecu Identification | The BCM part number is displayed. |
| Configuration | Read and save the vehicle specification. Write the vehicle specification when replacing BCM. |
SYSTEM APPLICATION
BCM can perform the following functions for each system.
Note. It can perform the diagnosis modes except the following for all sub system selection items.
| X: Applicable item | ||||
|---|---|---|---|---|
| System | Sub system selection item | Diagnosis mode | ||
| Work Support | Data Monitor | Active Test | ||
| Door lock | DOOR LOCK | X | X | X |
| Rear window defogger | REAR DEFOGGER | X | X | |
| Warning chime | BUZZER | X | X | |
| Interior room lamp timer | INT LAMP | X | X | X |
| Exterior lamp | HEAD LAMP | X | X | X |
| Wiper and washer | WIPER | X | X | X |
| Turn signal and hazard warning lamps | FLASHER | X | X | X |
| Air conditioning system | AIR CONDITONER | X | X (1) | |
| Intelligent Key system Engine start system | INTELLIGENT KEY | X | X | X |
| Combination switch | COMB SW | X | ||
| Body control system | BCM | X | ||
| NVIS - NATS | IMMU | X | X | X |
| Interior room lamp battery saver | BATTERY SAVER | X | X | X |
| Back door open | TRUNK | X | ||
| Theft warning alarm | THEFT ALM | X | X | X |
| RAP | RETAINED PWR | X | ||
| Signal buffer system | SIGNAL BUFFER | X | X | |
| TPMS | AIR PRESSURE MONITOR | X | X | X |
| NOTE: (1) For models with automatic A/C, this diagnosis mode is not used. | ||||
| NOTE |
|---|
| (1) For models with automatic A/C, this diagnosis mode is not used. |
| (1) | For models with automatic A/C, this diagnosis mode is not used. |
CONSULT performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|---|
| Work Support | Changes the setting for each system function. |
| Self Diagnostic Result | Displays the diagnosis results judged by BCM. |
| CAN Diag Support Monitor | Monitors the reception status of CAN communication viewed from BCM. |
| Data Monitor | The BCM input/output signals are displayed. |
| Active Test | The signals used to activate each device are forcibly supplied from BCM. |
| Ecu Identification | The BCM part number is displayed. |
| Configuration | Read and save the vehicle specification. Write the vehicle specification when replacing BCM. |
BCM can perform the following functions for each system.
Note. It can perform the diagnosis modes except the following for all sub system selection items.
| X: Applicable item | ||||
|---|---|---|---|---|
| System | Sub system selection item | Diagnosis mode | ||
| Work Support | Data Monitor | Active Test | ||
| Door lock | DOOR LOCK | X | X | X |
| Rear window defogger | REAR DEFOGGER | X | X | |
| Warning chime | BUZZER | X | X | |
| Interior room lamp control | INT LAMP | X | X | X |
| Remote keyless entry system | MULTI REMOTE ENT | X | X | X |
| Exterior lamp | HEAD LAMP | X | X | X |
| Wiper and washer | WIPER | X | X | X |
| Turn signal and hazard warning lamps | FLASHER | X | X | |
| Air conditioning system | AIR CONDITONER | X | X | |
| Combination switch | COMB SW | X | ||
| Body control system | BCM | X | ||
| NATS | IMMU | X | X | |
| Interior room lamp battery saver | BATTERY SAVER | X | X | X |
| Back door open | TRUNK | X | ||
| Theft warning alarm | THEFT ALM | X | X | X |
| RAP system | RETAINED PWR | X | X | |
| Signal buffer system | SIGNAL BUFFER | X | X | |
| Panic alarm | PANIC ALARM | X | ||
| TPMS | AIR PRESSURE MONITOR | X | X | X |