GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| Weight | |
| Engine and transaxle assembly weight | 251 kg (554 lb) |
| Transaxle weight | 130 kg (287 lb) |
GENERAL SPECIFICATIONS
TORQUE SPECIFICATIONS
| Description | Nm |
|---|---|
| A/C compressor connector retainer | 25 |
| All-wheel drive link shaft assembly bracket bolt (6 required) | 47 |
| Auxiliary coolant pump bolts | 10 |
| Catalytic converter bracket bolt (2 required) | 25 |
| Catalytic converter bracket nut (2 required) | 25 |
| DC-to-DC converter nuts | 12 |
| Drain plug | 40 |
| Engine control harness retainer nut (2 required) | 6 |
| Engine support crossmember bolt (2 required) | 90 |
| Engine support crossmember nut | 90 |
| Fill plug | 40 |
| Front insulator bolt | 90 |
| Front insulator bolt (2 required) | 90 |
| Front insulator through bolt | 115 |
| Front roll restrictor bolt | 115 |
| Front wheel drive link shaft assembly bracket (4 required) | 47 |
| Lateral support crossmember bolt (4 required) | 115 |
| LH support through bolt | 103 |
| Link shaft bearing assembly-to-bracket nut (2 required) | 28 |
| Lower support insulator mount bolt (late build) | 80 |
| Lower support insulator nut (2 required) (late build) | 80 |
| Lower support insulator stud (2 required) (late build) | 12 |
| Lower support insulator through bolt (late build) | 115 |
| Manual control lever retaining nut | 10 |
| Motor electronics coolant pump bolt (2 required) | 20 |
| Motor electronics coolant temperature sensor | 20 |
| Motor electronics cooler bolt (2 required) | 6 |
| Power transfer unit (PTU) heat shield bolts | 14 |
| PTU housing assembly-to-transaxle bolt (3 required) | 70 |
| PTU housing assembly-to-transaxle bolt (10 m bolt) (1 required) | 47 |
| PTU-to-engine support bracket bolts | 40 |
| Rear insulator mount bracket bolt (3 required) | 25 |
| Rear insulator bolt | 90 |
| Rear mount heat shield nut (2 required) | 38 |
| Rear mount nut (4 required) | 38 |
| Rear roll restrictor-to-lateral support crossmember bolt | 90 |
| Rear roll restrictor bracket bolts | 55 |
| Rear transaxle mount bolt | 90 |
| Rear transaxle mount nut | 90 |
| RH engine mount bracket nut (2 required) | 90 |
| Selector lever bolt (4 required) | 25 |
| Shift cable bracket nut (2 required) | 23 |
| Shift cable grommet nut (2 required) | 11 |
| Steering coupling pinch bolt | 40 |
| Subframe bolts | 175 |
| Subframe nuts | 150 |
| Transaxle control cable nut (2 required) | 22 |
| Transaxle control splash shield bolt (2 required) | 15 |
| Transaxle coolant tube fittings (inlet/outlet) | 50 |
| Transaxle damper bolts (6 required) | 29 |
| Transaxle ground cable nut | 20 |
| Transaxle harness retainer bolt | 25 |
| Transaxle-to-engine bolt (10 required) | 47 |
| Upper insulator support bolt (2 required) | 25 |
| Upper support nut (2 required) | 90 |
TORQUE SPECIFICATIONS
See also:
• JACKING AND LIFTING