DTC P0113: INTAKE AIR TEMPERATURE SENSOR VOLTAGE HIGH Dodge Ram Wagon B1500

Note. For connector terminal identification, see CONNECTOR IDENTIFICATION . For circuit identification and wiring diagram, see RAM VAN & RAM WAGON wiring diagram in WIRING DIAGRAMS article.

Note. DTC P0113: INTAKE AIR TEMPERATURE SENSOR VOLTAGE HIGH is monitored with ignition on and battery voltage more than 10.4 volts. DTC may be stored in Powertrain Control Module (PCM) when PCM senses Intake Air Temperature (IAT) sensor voltage is more than 4.9 volts. Possible causes are: defective IAT sensor, defective PCM, defective connectors or defective wiring.

1. Turn ignition on, with engine off. Using scan tool, read IAT sensor voltage. If voltage is more than 4.5 volts, go to next step. If voltage is 4.5 volts or less, go to step 7).
2. Turn ignition off. Disconnect IAT sensor connector. (Схема №20) Clean and/or repair connector as necessary. Connect a jumper wire between IAT sensor connector, signal circuit (Black/Red wire) and sensor ground circuit (Black/Light Blue wire). Turn ignition on, with engine off. Using scan tool, read IAT sensor voltage. If voltage is less than one volt, replace IAT sensor. Perform TEST VER-5A. If voltage is one volt or more, go to next step.
3. Turn ignition off. Ensure IAT sensor connector is still disconnected. Connect a jumper wire between ground and IAT sensor connector, sensor ground circuit (Black/Light Blue wire). Using scan tool, read IAT sensor voltage. If voltage is less than one volt, repair open in sensor ground circuit. Perform TEST VER-5A. If voltage is one volt or more, go to next step.
4. Turn ignition off. Ensure IAT sensor connector is still disconnected. Clean and/or repair connector as necessary. Turn ignition on, with engine off. Using a voltmeter, check voltage on IAT sensor connector, signal circuit (Black/Red wire). If voltage is more than 6 volts, repair signal circuit for short to voltage. Perform TEST VER-5A. If voltage is 6 volts or less, go to next step.
5. Ensure ignition is off. Ensure IAT sensor connector is still disconnected. Disconnect PCM connectors. PCM is located in engine compartment. See PCM LOCATION table under SYSTEM DIAGNOSTICS. Clean and/or repair connectors as necessary. Using an ohmmeter, check resistance of IAT sensor signal circuit (Black/Red wire) between IAT sensor and PCM. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open signal circuit. Perform TEST VER-5A.
6. At this time, PCM is assumed to be defective. Replace PCM. Perform TEST VER-5A.
7. Turn ignition on, with engine off. Wiggle IAT sensor connector and wiring harness while monitoring IAT sensor voltage. If voltage changes while wiggling connector and wiring harness, repair connector or wiring harness that caused voltage to change. Perform TEST VER-5A. If voltage does not change, go to next step.
8. Turn ignition off. Visually inspect related connectors and wiring harness for damage. Repair connectors and wiring harness as necessary. Perform TEST VER-5A. If connectors and wiring harness are okay, go to next step.
9. Ensure ignition is on, with engine off. Using scan tool, read and record FREEZE FRAME data. Ensure CAUSED BY DTC matches DTC on DTC screen. If DTC matches, road test vehicle under conditions in FREEZE FRAME data. Using scan tool, read DTCs. If DTC P0113: INTAKE AIR TEMPERATURE SENSOR VOLTAGE HIGH returns, visually inspect related connectors and wiring harness for damage. Repair connectors and wiring harness as necessary. Perform TEST VER-5A. If DTC P0113: INTAKE AIR TEMPERATURE SENSOR VOLTAGE HIGH does not return, see «INACTIVE DTC CONDITION»(ref-139160-S32382818132002042600000). Test is complete.