Home ReviewsRefund
Home/Subaru/XV/Subaru XV GP (2011-2016)/Repair manual/Communication Devices/Body Control System (Diagnostics) (Except Wrx): Overview
Contents Wiring diagrams Section: Communication Devices All sections

Body Control System (Diagnostics) (Except Wrx): Overview Subaru XV GP

Communication Devices ~845 words

OPERATION

For details concerning the work procedure, refer to the "PC application help for Subaru Select Monitor".

Note. For details concerning DTC, refer to List of Diagnostic Trouble Code (DTC). < Refer to LIST OF DIAGNOSTIC TROUBLE CODE (DTC) . >

For details concerning the work procedure, refer to the "PC application help for Subaru Select Monitor".

For details concerning the work procedure, refer to the "PC application help for Subaru Select Monitor".

  1. On «Main Menu» display, select {Each System Check}.
  2. On «System Selection Menu» display, select {Integ. unit mode}.
  3. On «Integ. unit mode failure diag.» display, select {Work Support}.
  4. On «Work Support» display, select {Unit customizing}.
  5. Change the setting with UP/DOWN key and set with the [OK] key. LIST OF USER CUSTOMIZING ITEM Data Initial setting value Customize setting Remarks Off delay time 30s OFF Room light off delay time can be selected. 10 Sec 20 Sec 30s Auto Light Sensitivity Adjustment Normal Dull Slow response Normal Standard Sensitive Quick response Very sensitive Fairly quick response Power rear gate setting - ( (1) ) ON Fixed at OFF because this is not applicable. OFF Back auto rear wiper setting - ( (1) ) ON Fixed at OFF because this is not applicable. OFF TPMS Setting - ( (1) ) TPMS Set to "ON" for model with TPMS. No TPMS Rr defogger op. mode Normal Normal Automatically stops in 15 minutes after switch is turned to ON. Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF. Security Alarm Setup ON ON Security alarm (hazard, horn or siren) in active condition OFF Security alarm in inactive condition Impact Sensor Setup OFF ON Workable when Impact Sensor Setup is set to "ON". Impact sensor function becomes activated. OFF Impact sensor in inactive condition (Set to "OFF" in models without sensors.) Alarm delay setup ON After the keyless lock operation, the alarm monitor starts after the following delay time has passed. ON Delay time is 30 seconds. OFF Delay time is 0 seconds. Lockout prevention ON ON key lockout prevention function is activated. (The function does not operate if safety knob is locked by hand.) OFF Key lockout prevention function is deactivated. Impact sensor (OP) OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start).) OFF Vehicle is controlled in no impact sensor mode. Buzzer sounding setting ON ON When lock/unlock is selected by keyless entry system operation, buzzer operates. OFF When lock/unlock is selected by keyless entry system operation, buzzer does not operate. Abnormal warning lamp flashing setting ON ON When lock/unlock is selected by keyless entry system operation, hazard blinks. OFF When lock/unlock is selected by keyless entry system operation, hazard does not interlock. Passive Alarm OFF ON OFF Door open warning ON ON OFF Dome Light Alarm Setting OFF ON Room light illuminates interlocking with alarm. OFF Room light does not illuminate interlocking with alarm. Auto A/C ECU Setting - ON Diagnoses with auto A/C CM. OFF Diagnoses without auto A/C CM. wiperdeicer - ON Wiper deicer control is performed. OFF Wiper deicer control is not performed. Illumination Control On/Off ON ON OFF Sedan/Wagon Setting - Sedan Body control is performed by Sedan. Wagon Body control is performed by Wagon. MT/AT Setting - MT Body control is performed by MT. AT Body control is performed by AT. 6MT Setting - 6MT Body control is performed by 6MT. Other than 6MT Body control is performed by other than 6MT. Illumination Sensor Setting - ( (1) ) ON Set to "ON" for model with auto light. OFF Factory initial setting Market Market Customize setting is reset when mode is switched from Market to Factory. Factory (1) Customization item according to the actual vehicle equipment
  6. After setting, make sure that the setting changed in the {Current Data Display & Save} is same as vehicle equipment. CAUTION: the above settings must match the actual vehicle equipment. Do not change settings except for setting above while setting the functions. Be sure not to change Factory initial setting except when installing a new body integrated unit. NOTE: For detailed operation procedures, refer to "PC application help for Subaru Select Monitor".

Note. In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.

  1. On «Main Menu» display, select {Each System Check}.
  2. On «System Selection Menu» display, select {Integ. unit mode}.
  3. On «Integ. unit mode failure diag.» display, select {Work Support}.
  4. On «Work Support» display, select {Active Test}.
  5. Select an item to be operated on «Active Test» display, and press the [OK] button.
  6. Pressing [Next] starts, [End] cancels the operation and [OK] returns to the System Operation Check Mode display screen. NOTE: If not equipped (based on area or condition), process will not go on. For detailed operation procedures, refer to "PC application help for Subaru Select Monitor".

More articles — Body Control System (Diagnostics) (Except Wrx)